Da-Lite Da-Tex (Rear) Handleiding

Da-Lite Projectiescherm Da-Tex (Rear)

Lees hieronder de 📖 handleiding in het Nederlandse voor Da-Lite Da-Tex (Rear) (8 pagina's) in de categorie Projectiescherm. Deze handleiding was nuttig voor 75 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

DA-LITE SCREEN COMPANY, INC.

3100 North Detroit Street

Post Office Box 137

Warsaw, Indiana 46581-0137

Phone: 574-267-8101

800-622-3737

Fax: 574-267-7804

Toll Free Fax: 877-325-4832

www.da-lite.com

e-mail: info@da-lite.com

Instruction Book for

TENSIONED ADVANTAGE® ELECTROL®

The Da-Lite Difference.

1. Remove 2 screws to open junction box.

2. Hang case and attach to support structure with threaded rod. See suggested methods of installation on page 5.

3. Tighten bolts until trim flange is flush with ceiling.

NOTE: For proper operation, screen assembly must be level after installation.

4. Install electrical connections that applies to your unit. Make sure to review the wiring diagram for proper hook up.

NOTE: Must be installed in accordance with the requirements of the Local Building Codes, the Canadian Electrical Code (CEC),

CAN/CSA C22.1 and the National Electric Code (NEC), NFPA 70.

5. Replace junction box cover and secure with 2 screws.

6. If screen and case are purchased together, remove slat retainer brackets from the screen case and back of slat.

PRE-INSTALLATION

1. Carefully unpack case from shipping carton. DO NOT unpack fabric and roller assembly yet.

2. Make sure to recheck measurement of case for proper installation clearance.

3. Remove any protective foam or tape from case.

CASE INSTALLATION

IMPORTANT SAFETY INSTRUCTIONS

When using your video equipment, basic safety precautions should always be followed, including the

following:

1. Read and understand all instructions before using.

2. Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.

3. If an extension cord is necessary, a cord with a current rating at least equal to that of the appliance

should be used. Cords rated for less amperage than the appliance may overheat.

4. To reduce the risk of electric shock, do not disassemble this appliance. Contact an authorized

service dealer when repair work is required. Incorrect reassembly can cause electric shock when

the appliance is used subsequently.

5. The use of an accessory attachment not recommended by the manufacturer may cause a risk of

fire, electric shock, or injury to persons.

SAVE THESE INSTRUCTIONS

If your screen was shipped with the motor and roller already installed, proceed to step 6.

1. Remove access door. First, remove the 2 screws from the ends. Be sure to support the door during this

step to avoid injury. Then lift the door slightly and pull away from the edge of the case.

2. Carefully unpack screen and roller assembly. Leave packing paper on roller.

3. To install screen and roller assembly, insert the motor end into the motor mount bracket as shown in Fig. 1.

4. Loosen (but do not remove) two 1/4-20 nuts securing pin end bracket (stage left) to the case housing. Slide the

bracket towards the end of the case. Insert the motor end square shaft into the motor end bracket and secure with

the clip.Insert the tip of the roller pin end into the bracket and position. Tighten the 1/4-20 nuts securely.

5. Complete electrical hook-up by snapping motor wire connector into case connector.

6. Carefully remove paper and tape from roller assembly. use a knife or sharp object to cut tape; you will DO NOT

damage the screen.

7. Test installation by running screen up and down a few times. Be prepared to stop screen. Standard Duty Cycle: 1

MIN. ON / 3 MIN. OFF.

8. Re-install access door. Procedure is reverse of removal (step 1).

SCREEN AND ROLLER ASSEMBLY INSTALLATION

ADVANTAGE® ELECTROL® INSTALLATION

7-3/4"

6-1/16" 3/8" THREADED ROD

(NOT INCLUDED)

ATTACHED TO

MOUNTING BRACKET

SELF-TRIMMING

FLANGE

6-3/8"

7-3/4"

FINISHED

CEILING

6.42"

3/8" THREADED ROD

(NOT SUPPLIED)

HANGER BRACKET

SEE DETAIL A

7.75"

DETAIL A

7.95"

3.41"

ELECTRICAL

JUNCTION BOX

MOTOR END

VARIABLE POSITION

MOUNTING BRACKET

AUDIENCE

SIDE

6-1/16"

6-7/16"

FIGURE 1

Product specificaties

Merk:	Da-Lite
Categorie:	Projectiescherm
Model:	Da-Tex (Rear)
Kleur van het product:	Black, White
Gewicht:	10886 g
Oorspronkelijke beeldverhouding:	4:3
Montagewijze:	Muur
Zichtbare schermhoogte (h):	1220 mm
Zichtbare schermbreedte (b):	910 mm
Diagonaal:	60 "
Totale grootte van het scherm (hoogte x breedte):	91 x 122 cm
Formaat:	Video