Da-Lite Scenic Roller 40380 Handleiding

Da-Lite Projectiescherm Scenic Roller 40380

Lees hieronder de 📖 handleiding in het Nederlandse voor Da-Lite Scenic Roller 40380 (4 pagina's) in de categorie Projectiescherm. Deze handleiding was nuttig voor 36 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

INSTRUCTION BOOK FOR

Scenic Roller

Pre-Installation Installation

Having decided on hooks, chains, cables or other mounting

method, have mounting prepared before opening box.

Do not mount screen against walls that might rub fabric.

1. Remove screen from box by lifting roller at the ends. Be

careful not to permit lid or any tools to fall on screen. During

installation handle unit only by ends of roller and top header.

Do not grasp around fabric –do not rest unit on fabric.

2. Remove wrapping paper and unwind ropes.

3. With the screen lying on the loor, install the clamps on the

reinforcement tape on the header as shown in Figure 2.

Clamp assembly is shown in Figure 1. Drop the closed loop of

the turnbuckle in the slot of the clamp before inserting bolt.

Each clamp uses three bolts and nuts. Do not tighten nuts

any more than inger tight. Make sure the ends of clamps do

not push into the fabric. Pulleys at each end of header must

be in the vertical position, when hung for proper operation.

4. Adjust top header in fabric pocket to the 21/4" and 33/4"

position shown on the drawing.

5. Hang the screen in place at three, ive, or seven points.

CAUTION! When this screen is shipped from the factory,

there are 2-1/2 turns of rope around each end of the roller.

Make certain that this is left unchanged to insure good

operation.

CAUTION! Before dropping fabric make certain ropes

at end of bottom roller do not overlap. Overlapping of

ropes will cause rope to work inward and thus damage

the fabric.

Figure 1 – Clamp Assembly

1. Lower screen slowly by gradually releasing ropes.

2. With screen in the “Down” position, turn the header in the

fabric pocket carefully to adjust the pulleys to a vertical end

position. Check the 21/4" and 33/4" end tube dimensions.

Adjust the clamps on the reinforcement tape. Clamps are not

to push into fabric pocket. Tighten nuts on all bolts.

3. Total screen drop may be controlled by adjusting rope clamp.

Do not adjust for more drop.

4. With unit in completely unrolled position, examine the screen

carefully. If slight sag appears in center of fabric, adjust

turnbuckles at the eye bolts until fabric hangs lat.

5. Screen may be raised by pulling on ropes. Tie of ropes to

keep screen in raised position.

6. Protect your screen against damage and it will give many

years of enjoyment.

a. When lowering screen, do so gently. Never allow it to

drop uncontrolled.

b. Before raising screen, be sure both front and back sides

are free from insects or any foreign matter.

c. Form the habit of looking in space between fabric and

roller for foreign matter before raising screen.

d. Caution stage hands and others to avoid bumping

screen with ladders, scenery, etc.

Screen Adjustment

Don't Adjust

Rope Clamp

Already Set

for Proper

Full Screen

Opening

Mount Header

Tube Level

Locate Clamps on

Reinforcement Tape

Mount at These Points Only

Turnbuckle – Adjust

for Flat Fabric Hang

Do Not Handle Unit by

Fabric Area

Pulley Must be Installed

in The Vertical Position

Check Here for Foreign

Matter Before Raising

Screen

Center Line of Screen

Handle Unit Only

by Top Header and

Roller Ends During

Installation

Figure 2

2 ¼" 3 ¾"

6" 6"

Product specificaties

Merk:	Da-Lite
Categorie:	Projectiescherm
Model:	Scenic Roller 40380
Kleur van het product:	Black, White
Oorspronkelijke beeldverhouding:	1:1
Montagewijze:	Muur
Zichtbare schermhoogte (h):	5486 mm
Zichtbare schermbreedte (b):	7315 mm
Diagonaal:	360 "
Type aandrijving:	Handmatig
Formaat:	Vierkant