CyberPower VALUE2200E-GP Handleiding

CyberPower UPS VALUE2200E-GP

Lees hieronder de 📖 handleiding in het Nederlandse voor CyberPower VALUE2200E-GP (2 pagina's) in de categorie UPS. Deze handleiding was nuttig voor 16 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

1200E/1500E/2200E

User’s Manual K01-0000032-01

SAFETY WARNINGS

(SAVE THESE INSTRUCTIONS)

This manual contains important safety instructions. Please read and follow all instructions carefully

during installation and operation of the unit. Read this manual thoroughly before attempting to unpack,

install, or operate your UPS.

This equipment can be operated by any individuals with no previous training.

The socket-outlet shall be installed near the equipment and easily accessible.

During the installation of this equipment it should be assured that the sum of the leakage currents of the

UPS and the connected loads does not exceed 3.5mA.

Attention, hazardous through electric shock. Also with disconnection of this unit from the mains,

hazardous voltage still may be accessible through supply from battery. The battery supply should be

therefore disconnected in the plus and minus pole at the quick connectors of the battery when

maintenance or service work inside the UPS is necessary.

Do not dispose of batteries in a fire, the battery may explode.

Do not open or mutilate the battery or batteries, released electrolyte is harmful to the skin and eyes.

INSTALLING YOUR UPS SYSTEM

UNPACKING

Inspect the UPS upon receipt. The box should contain the following:

UPS Unit¯1; IEC Power Cord¯1;USB Cable¯ ¯1;User Manual 1; Management software Disk¯1

HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT

1. Insure that the equipment plugged into the battery power-supplied outlets does not exceed the UPS

unit’s rated capacity (1200VA/720W for Value 1200E, 1500VA/900W for Value 1500E,

2200VA/1320W for Value 2200E). If rated unit capacities are exceeded, an overload condition may

occur and cause the UPS unit to shut down or the fuse blow.

2. If the power requirements of your equipment are listed in units other than Volt-Amps (VA), convert

Watts (W) or Amps (A) into VA by doing the calculations below. Note: The below equation only

calculates the maximum amount of VA that the equipment can use, not what is typically used by the

equipment at any one time. Users should expect usage requirements to be approximately 60% of

below value.

TO ESTIMATE POWER REQUIREMENTS

1. Watts (W) x 1.67 = VA or Amps (A) x 230 = VA

2. Add the totals up for all pieces of equipment and multiply this total by 0.6 to calculate actual

requirements. There are many factors that can affect the amount of power that your computer system

will require. The total load that you will be placing on the battery-powered outlets should not exceed

80% of the unit’s capacity.

HARDWARE INSTALLATION GUIDE

Before installation, please read and understand the following instructions:

1. Placement

The UPS must be installed in a protected environment away from heat- emitting appliances such

as a radiator or heat register. Do not install this product where excessive moisture is present.

2. Ventilation

The location should provide adequate air flow around the UPS with one inch minimum clearance

on all sides for proper ventilation.

3. Charge the Battery

Your new UPS may be used immediately upon receipt. However charge loss may occur during

shipping and storage. So charging the battery for at least 8 hours is recommended to insure that

the battery is fully charged. (To recharge the battery, simply leave the unit plugged into an AC

outlet.)

This UPS can be charged even when UPS is not turn on.

4. Connect to AC

Use German power cord to connect the UPS to a wall

outlet. Please avoid using extension cords and

adapter plugs. (To maintain optimal battery charge,

leave the UPS plugged in at all times.)

5. Connect the Load

Connect the equipment to your UPS outlets. The IEC

power cord coming with the unit are used to connect

your computer and monitor to the UPS. Items such

as copiers, laser printers, vacuums, space heaters,

or other large electrical devices SHOULD NOT be connected to the UPS. Please make sure

that the total loads of your equipments are less than the maximum total power load of your UPS.

6. Connect to Computer:

Install your software and accessories. To use the software, simply use the enclosed serial interface

or USB cable to connect the UPS unit and your computer.

BASIC OPERATION

FRONT PANEL DESCRIPTION

1. Power Switch

Press the power switch to turn the UPS ON or OFF.

2. LCD Function Selected Switch

The switch can be used to select the LCD display contents Including input/output voltage

and estimated run time, etc.

REAR PANEL DESCRIPTION

1. AC Inlet

Connect to utility power through the input power cord

2. Input Circuit Breaker

The circuit breaker provides optimal overload protection.

3. AC outlet

The UPS provides 6 outlets for connected equipment to insure temporary uninterrupted operation

during a power failure and against surges and spikes.

4. Serial Port to PC

This port allows connection and communicates

from the DB-9 serial on the computer to the

UPS unit. The UPS communicates its status to

the PowerPanel® Personal Edition software. This

interface is also compatible with the UPS service

provided by Windows 98, Windows ME,

Windows NT, Windows 2000, Windows XP,

Windows Server 2003, Windows Vista.

5. USB Port to PC

This port allows connection and communication

from the USB port on the computer to the UPS

unit. The UPS communicates its status to the

PowerPanel® Personal Edition software. This

interface is also compatible with the UPS service

provided by Windows 98, Windows ME,

Windows NT, Windows 2000, Windows XP,

Windows Server 2003, Windows Vista.

NOTE: Only one of these two ports

can be used as communication and

control of the UPS unit at one time.

6. Communication Protection Ports RJ11/RJ45

Communication protection ports will protect any standard modem, fax, telephone line, or network

cable.

Functional Test

AC Mode

The UPS delivers power to the loads derived from the utility and maintains proper battery charge. It also

regulates the output voltage to within a narrow range.

On-Battery Mode

The UPS operates on battery when the line voltage or frequency has fallen outside the limits. Local

users are alerted to this mode of operation by visual and audible indicators. The UPS provides power to

the load from the battery and through its inverter and the output voltage and frequency of the UPS are

regulated within a narrow range

1. Switch On

Press the power switch on the front panel then the status LCD will light up.

2. Switch Off

Press again the power switch, the status LCD on the front panel will go off.

3. Cold Start / Start on Battery:

This UPS can be turned on even when AC is not present.

Press the power switch on the front panel then the status LCD will light up.

ROUTINE MAINTENANCE AND STORAGE

ROUTINE MAINTENANCE

1. Use dry soft clothes to clean the front panel and plastic parts. Do not use any detergent that

contains alcoholic ingredient.

2. The expected lifetime of the battery is around 3 years. Improper operation and harsh environment

will reduce the actual lifetime.

3. Unplug the UPS from power inlet if the UPS will not operate for long period of time.

STORAGE

1. First turn off your UPS and disconnect its power cord from the wall outlet. Disconnect all cables

connected the UPS to avoid battery drain.

2. The UPS should be stored in a cool dry location.

3. Make sure the battery is fully charged before the UPS is stored.

4. For extended storage in moderate climates, the battery should be charged for 12 hours every 3

months by plugging the power cord into the wall receptacle and turning on the main switch. Repeat

it every 2 months in high temperature locations.

TROUBLE SHOOTING

Problem Possible Cause Solution

Batteries are not fully

charged. Recharge the battery by leaving the UPS

plugged in.

The UPS does

not perform

expected

runtime. Battery is slightly worn out. Contact CyberPower Systems at

service@cyberpower-eu.com

The on/off switch is

designed to prevent

damage by rapidly turning it

off and on.

Turn the UPS off. Wait 10 seconds and

then turn the UPS on.

The unit is not connected to

an AC outlet. The unit must be connected to a

220-240V 50/60Hz outlet.

The battery is worn out. Contact CyberPower Systems at

service@cyberpower-eu.com

The UPS will not

turn on.

Mechanical problem. Contact CyberPower Systems at

service@cyberpower-eu.com

Circuit breaker is tripped

due to overload

Turn the UPS off and unplug at least one

piece connected equipment. Unplug the

power cord of the UPS then press the

circuit breaker knob.

Batteries are discharged Allow the unit to recharge for at least 4

hours.

Outlets do not

provide power to

equipment

Unit has been damaged by

a surge or spike. Contact CyberPower Systems at

service@cyberpower-eu.com

The serial/USB cable is not

connected.

Connect the serial/USB cable to the UPS

unit and an open serial port on the back

of the computer. You must use the cable

that came with the unit.

The serial/USB cable is

connected to the wrong

port.

Try another serial/USB port of your

computer.

The unit is not providing

battery power.

Shutdown your computer and turn the

UPS off. Wait 10 seconds and turn the

UPS back on. This should reset the unit.

PowerPanel®

Personal Edition

is inactive (all

icons are gray).

The serial cable is not the

cable that was provided with

the unit.

You must use the cable included with the

unit for the software.

CyberPower warrants to you, the original purchaser, that CyberPower UPS will be free from defects in

design, assembly, materials and workmanship for two years ( battery is only one year) from the date of

original purchase. Any warranty services, please contact your local dealers or distributors.

TECHNICAL SPECIFICATIONS

Model Value 1200E Value 1500E Value 2200E

Capacity (VA) 1200VA 1500VA 2200VA

Capacity (Watts) 720W 900W 1320W

Input

Input Voltage Range 160VAC~270VAC

Frequency Range 50/60Hz +/-3Hz(Auto Sensing)

Output

On Battery Output

Voltage Simulated Sine Wave at 230Vac +/-7%

On Battery Output

Frequency 50/60 Hz

Overload Protection On Utility: Circuit Breaker, On Battery: Internal Current Limiting

Physical

Total # of UPS

Receptacles (6) IEC 320 C13

Maximum Dimensions 32.6cm(L)

14.cm(W)

18cm(H)

Weight 13.0 kg / 28.6 Lbs 14.3 kg / 31.5 Lbs 15.4 kg / 33.9 Lbs

Battery

Sealed Maintenance

Free Lead Acid Battery 12V / 7Ah p2-x2 12V / 8.5Ah p2-x2 12V / 9Ah p2-x2

Typical Recharge Time 8 Hours

Warning Diagnostics

Indicators Power On, UPS Status Display, Capacity Display, Digital Value

Display

Audible Alarms On Battery, Low Battery, Overload

Environmental

Operating Temperature +32°F to 104°F ( 0°C to 40°C )

Operating Relative

Humidity 0 to 95% NON-CONDENSING

Communication

PowerPanel® Personal

Edition Software Windows 98/ME/2000/NT/XP/Vista

Management

Auto-Charger Yes

Auto-Restart Yes

USB Yes

DEFINITIONS FOR ILLUMINATED LCD INDICATORS

LCD Indication

Line mode

UPS Status Display Capacity Display Digital Value Display

Select SW

Press Load

Cap.

Battery

Cap.

Input

Voltage

Output

Voltage

Run

Time

of Load

of Batt.

Initial V X -- X V X V

1st V X -- X V X V

2nd V X -- X V X V

3rd V X -- X X V V

4th V X -- X V X V

5th(Return) V X -- X V X V

Press >3sec

(Sound Disable) V X V X -- -- -- -- -- -- --

Press >3sec

again

(Sound Enable)

V X X X -- -- -- -- -- -- --

(Overload) V X -- V -- -- -- -- -- -- --

“V” : Illuminated, “X” : Not Illuminated, “--“ : Either

Battery mode

UPS Status Display Capacity Display Digital Value Display

Select SW

Press Load

Cap.

Battery

Cap.

Input

Voltage

Output

Voltage

Run

Time

of Load

of Batt.

Initial X V -- X X V V

1st X V -- X X V V

2nd X V -- X V X V

3rd X V -- X X V V

4th X V -- X X V V

5th(Return) X V -- X X V V

Press >3sec

(Sound Disable) X V V X -- -- -- -- -- -- --

Press >3sec

again

(Sound Enable) X V X X -- -- -- -- -- -- --

(Overload) X V -- V -- -- -- -- -- -- --

“V” : Illuminated, “X” : Not Illuminated, “--“ : Either

For more information, visit eu.cyberpowersystems.com or contact

CyberPower Systems B.V.

Flight Forum 3545 5657DW Eindhoven The Netherlands

Tel: +31 40 2348170, E-MAIL: sales@cyberpower-eu.com

CyberPower Systems Inc. (USA) 4241 12th Avenue East, Suite 400, Shakopee, MN 55379, U.S.A.

Tel: +1 952 4039500, Fax: +1 952 4030009, E-MAIL: sales@cyberpowersystems.com

or in part without permission is prohibited. PowerPanel

and PowerPanel® Plus are trademarks of

CyberPower Systems (USA) Inc.

Product specificaties

Merk:	CyberPower
Categorie:	UPS
Model:	VALUE2200E-GP
Kleur van het product:	Zwart
Gewicht:	15100 g
Breedte:	140 mm
Diepte:	326 mm
Hoogte:	160 mm
LED-indicatoren:	Power, Battery replacement
Vormfactor:	Compact
Aantal USB 2.0-poorten:	1
Aantal Ethernet LAN (RJ-45)-poorten:	1
Geluidsalarm(en):	Ja
Responstijd:	4 ms
Meegeleverde software:	PowerPanel Personal
Uitgangsvermogen:	1320 W
Accu/Batterij oplaadtijd:	8 uur
Stroomspanning bescherming:	Overbelasting
Frequentie:	50/60 Hz
Overbelastingsprotectie:	Ja
Seriële poort(en):	1
Modem (RJ-11) poort:	1
Stekker:	C14 stekker
Batterijtechnologie:	Sealed Lead Acid (VRLA)
Type beeldscherm:	LCD
Aantal AC uitgangen:	6 AC-uitgang(en)
Golf protectie functies:	Fax, Modem, Network, Telephone
Output power capacity:	2.2 kVA
Ingang operation voltage (min):	160 V
Ingang operation voltage (max):	265 V
Uitgang operation voltage (min):	230 V
Uitgang operation voltage (max):	230 V
Typische backup tijd op halve lading:	7 min
Typische backup tijd op volledige lading:	1 min
Hoorbare alarmstanden:	Batterijvervanging
Spanningsbeveiliging:	Ja