CyberPower Standby CP550SL Handleiding
CyberPower
UPS
Standby CP550SL
Lees hieronder de đź“– handleiding in het Nederlandse voor CyberPower Standby CP550SL (2 pagina's) in de categorie UPS. Deze handleiding was nuttig voor 25 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/2
CP550SL / AE550
User’s Manual
K01-AE55000
IMPORTANT SAFETY WARNINGS
(SAVE THESE INSTRUCTIONS)
This manual contains important safety instructions. Please read and follow all instructions carefully during installation and operation of the
unit. Read this manual thoroughly before attempting to unpack, install, or operate your UPS.
CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity controlled indoor area free of conductive
contaminants. (Please see specifications for acceptable temperature and humidity range).
CAUTION! To reduce the risk of electric shock, do not remove the cover except to service the battery. No user serviceable parts inside
except for battery.
CAUTION! Hazardous live parts inside can be energized by the battery even when the AC input power is disconnected.
CAUTION! UPS must be connected to an AC power outlet with fuse or circuit breaker protection. Do not plug into an outlet that is not
grounded. If you need to de-energize this equipment, turn off and unplug the unit.
CAUTION! To avoid electrical shock, turn off the unit and unplug it from the AC power source before servicing the battery or installing a
computer component.
DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT! CyberPower Systems does not sell products for life support or medical
applications. DO NOT use in any circumstance that would affect operation or safety of any life support equipment or with any medical
applications or patient care.
DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of fire or electric shock, do not use with or near an aquarium.
Condensation from the aquarium can cause the unit to short out.
DO NOT USE WITH LASER PRINTERS! The power demands of these devices will overload and possibly damage the unit.
INSTALLING YOUR UPS SYSTEM
UNPACKING
Inspect the UPS upon receipt. The box should contain the following:
(1) UPS unit; (1) User’s manual; (1) PowerPanel™ Personal Edition software CD; (1) USB device cable; (1) Telephone cable; (1) Warranty
registration card
HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT
1. Make sure that the total Volt-Amp (VA) requirements of your computer, monitor and peripheral equipment does not exceed 1440VA.
2. Ensure that the equipment plugged into the four battery power-supplied outlets does not exceed the UPS unit’s rated capacity
(550VA/330W for CP550SL / AE550). If rated unit capacities are exceeded, an overload condition may occur and cause the UPS unit to
shut down or the circuit breaker to trip.
3. If the power requirements of your equipment are listed in units other than Volt-Amps (VA), convert Watts (W) or Amps (A) into VA by
doing the calculations below. Note: The below equation only calculates the maximum amount of VA that the equipment can use, not
what is typically used by the equipment at any one time. Users should expect actual usage values to be approximately 60% of the
calculated values. To estimate power requirements:
Watts (W) x 1.67 = VA or Amps (A) x 120 = VA
Add the totals up for all pieces of equipment and multiply this total by .6 to calculate actual power requirements.
There are many factors that can affect the amount of power that your computer system will require. The total load that you will be
placing on the battery-powered outlets should not exceed 80% of the unit’s capacity.
HARDWARE INSTALLATION GUIDE
1. Your new UPS may be used immediately upon receipt. However, recharging the battery
for at least 16 hours is recommended to insure that the battery’s maximum charge
capacity is achieved. A loss of charge may occur during shipping and storage. To
recharge the battery, simply leave the unit plugged into an AC outlet. The unit will charge
in both the ON as well as the OFF position. If you wish to use the software, use the enclosed
USB device cable to connect the UPS to your computer. If you are not going to use the
software, you do not need to connect the cable.
2. With the UPS unit turned off and unplugged, connect your computer, monitor and any externally powered data storage device (Zip drive,
Jazz drive, Tape drive, etc…) into the battery power supplied outlets. Plug your peripheral equipment (printer, scanner, speakers) into
the full-time surge protection outlets. DO NOT plug a laser printer, paper shredder, copier, space heater, vacuum or other large
electrical device into the UPS. The power demands of these devices will overload and possibly damage the unit.
3. To protect a fax, phone or modem, connect a telephone cable from the wall jack outlet to the in jack of the UPS.
Connect a telephone cable from the out jack with the CPU icon to the modem port on your computer. The out jack
with the telephone icon can be used to protect a telephone or fax machine.
4. Plug the UPS into a 2 pole, 3 wire grounding receptacle (wall outlet). Make sure the wall branch outlet is protected
by a fuse or circuit breaker and does not service equipment with large electrical demands (e.g. refrigerator, copier,
etc…). The warranty prohibits the use of extension cords, outlet strips, and surge strips.
5. Press the power switch to turn the unit on. The power on indicator light will illuminate and the unit will “beep” once.
6. If an overload is detected, an audible alarm will sound and the unit will emit one long beep. To correct this, turn the UPS off and unplug
at least one piece of equipment from the battery power supplied outlets. Wait 10 seconds. Make sure the circuit breaker is depressed
and then turn the UPS on.
7. Your UPS is equipped with an auto-charge feature. When the UPS is plugged into an AC outlet, the battery will automatically recharge.
8. To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times.
9. To store your UPS for an extended period, cover it and store with the battery fully charged. While in storage recharge the battery every
three months to insure battery life.
BASIC OPERATION
DESCRIPTION
Battery and Surge Protected Outlets
The unit has four battery powered/surge protected outlets for
connected equipment and ensures temporary uninterrupted
operation of your equipment during a power failure.
Full-Time Surge Protection Outlets
The unit has four always on surge suppression outlets.
Power Switch
Can be used as a master on/off switch for equipment
connected to the battery power supplied outlets.
Power On Indicator
This LED is illuminated when the utility condition is normal and the UPS outlets are providing power, free of surges and spikes.
Electrical Wiring Fault Indicator
This LED indicator will illuminate to warn the user that a wiring problem exists, such as bad ground, missing ground or reversed wiring.
If this is illuminated, user is advised to disconnect all electrical equipment from the outlet and have an electrician check to ensure the
outlet is properly wired. The unit will not provide surge protection without being plugged into a grounded and properly wired wall outlet.
Communication Protection Ports
Communication protection ports will protect any standard modem, fax or telephone line.
Circuit Breaker
Located on the side of the UPS, the circuit breaker serves to provide overload and fault protection.
Serial/USB Ports to PC
The ports allow connection and communication from the USB or DB-9 serial port on the computer to the UPS unit. The UPS
communicates its status to the PowerPanel™ Personal Edition software. This interface is also compatible with the Power
Management UPS control provided by Windows
â—‹
â—‹
â—‹
â—‹â—‹
R 2000 and Windows
â—‹
â—‹
â—‹
â—‹â—‹
R XP.
Note: Only one of these two ports can be used to communicate with your computer at one time.
Note: To install PowerPanel™ Personal Edition Software the computer will need Microsoft
â—‹
â—‹
â—‹
â—‹â—‹
R Internet Explore 5.0 or higher
installed.
Note: If using the Serial Port, users need to download Power Panel
â—‹
â—‹
â—‹
â—‹â—‹
R software from our website
http://www.cyberpowersystems.com and order the standard serial cable. If you have any questions email CyberPower
technical support for help. tech@cyberpowersystems.com
Outlets Designed for AC Adapters
The unit has four outlets spaced to allow AC power adapter blocks to be plugged into the UPS without blocking adjacent outlets.
Vertical Use
The unit can be placed on it’s end in a vertical orientation.
Note: We recommend you place the unit next to the wall when standing the unit vertically.
REPLACING THE BATTERY
CAUTION! Read and follow the IMPORTANT SAFETY INSTRUCTIONS before servicing the battery. Service the battery under the
supervision of personnel knowledgeable of batteries and their precautions.
CAUTION! Use only the specified type of battery. See your dealer for replacement batteries.
CAUTION! The battery may present a risk of electrical shock. Do not dispose of battery in a fire as it may explode. Follow all local
ordinances regarding proper disposal of batteries. Almost any retailer that sells lead-acid batteries collects used batteries for recycling, as
required by most state laws.
CAUTION! Do not open or mutilate the batteries. Released electrolyte is harmful to skin and eyes and may be toxic.
CAUTION! A battery can present a high risk of short circuit current and electrical shock. Take the following precautions before replacing
the battery:
1. Remove all watches, rings or other metal objects.
2. Only use tools with insulated handles.
3. Do not lay tools or metal parts on top of battery or any terminals.
4. Wear rubber gloves and boots.
5. Determine if the battery is inadvertently grounded. If grounded, remove the source of ground. CONTACT WITH GROUNDED BATTERY
CAN RESULT IN ELECTRICAL SHOCK!
TO REPLACE THE BATTERY
1. Turn off and unplug all connected equipment.
2. Turn the UPS off and unplug it from the AC power source.
3. Turn the UPS upside down.
4. Remove the 1 retaining screw.
5. Slide the battery compartment cover completely off of the unit.
6. Remove the battery from the compartment.
7. Disconnect the battery wires from the battery.
8. Install the replacement battery by connecting the red wire and black wire to the positive (+) and negative (-) terminal of the battery.
9. Put the battery back into the compartment.
10. Slide back the battery compartment cover and tighten the retaining screw.
11. Recharge the unit for 4 – 8 hours to fully charge the battery.
REMINDER: Batteries are consider HAZARDOUS WASTE and must be disposed of properly. Almost any retailer that sells lead-acid
batteries collects used batteries for recycling, as required by most state laws.
TROUBLE SHOOTING
Problem Possible Cause Solution
Full-time surge protection outlets
stop providing power to
equipment. Circuit breaker
button is projecting from the side
of the unit.
Circuit breaker has tripped due to an
overload.
Turn the UPS off and unplug at least one piece of equipment.
Wait 10 seconds, reset the circuit breaker by depressing the
button, and then turn the UPS on.
Battery not fully charged. Recharge the battery by leaving the UPS plugged in.
The UPS does not perform
expected runtime.
Battery is slightly worn out. Contact CyberPower Systems about replacement batteries at
tech@cyberpowersystems.com
The on/off switch is designed to
prevent damage by rapidly turning it
off and on.
Turn the UPS off. Wait 10 seconds and then turn the UPS on.
The unit is not connected to an AC
outlet. The unit must be connected to a 110/120v 60Hz outlet.
The battery is worn out. Contact CyberPower Systems about replacement batteries at
tech@cyberpowersystems.com
The UPS will not turn on.
Mechanical problem. Contact CyberPower Systems at
tech@cyberpowersystems.com
The USB / serial cable is not
connected.
Connect the USB / serial cable to the UPS unit and an open
USB / serial port on the back of the computer. You must use
the cable that came with the unit.
The USB / serial cable is connected
to the wrong port.
Check the back of the computer for an additional USB / serial
port. Move the cable to this port.
The unit is not providing battery
power.
Shutdown your computer and turn the UPS off. Wait 10
seconds and turn the UPS back on. This should reset the unit.
PowerPanel™ Personal Edition
is inactive (all icons are gray).
The serial cable is not the cable that
was included with the UPS unit.
If you are using a serial cable you must use a CyberPower serial
cable. If you need this cable please contact technical support.
tech@cyberpowersystems.com
Additional troubleshooting information can be found at
www.cyberpowersystems.com/support.htm
TECHNICAL SPECIFICATIONS
Model CP550SL / AE550
Capacity 550VA / 330W
Input Voltage on Utility 100V to 140V
Input Frequency 57 Hz to 63 Hz
On-Battery Output Voltage 120Vac ± 5%
Transfer Time 4ms Typical
Max. Load for UPS Outlets (4 Outlets) 550VA / 330W
Max. Load for Full-Time Surge Protection outlets (8 Outlets) 12 Amps
On-Battery Output Wave Form Simulated Sine Wave Form
Operating Temperature + 32°F to 95° F / 0° C to 35° C
Operating Relative Humidity 0 to 95% NON-CONDENSING
Size (L x W x H) 10 2/3” x 6 1/2” x 3 1/2” / 27.1cm x 16.5cm x 8.7cm
Net Weight 12.5 lbs
Typical Battery Recharge Time 8 hours typical from total discharge
Typical Battery Life 3 to 6 years, depending on number of discharge/recharge cycles
Battery Type 12V / 8.0AH
Recommended Battery Spill-proof, Maintenance-free, sealed lead-acid
Safety Approvals UL1778(UPS), cUL107., FCC/DoC Class B
EXPECTED RUNTIME IN MINUTES
(Due to differences in computer components, the runtime will vary.)
Model iMac G4 Desktop PC with
LCD Monitor
Desktop PC
with 15” Monitor
Desktop PC
with 17” Monitor
Desktop PC
with 21” Monitor
CP550SL
AE550 60 minutes 43 minutes 24 minutes 20 minutes 15 minutes
DEFINITIONS FOR ILLUMINATED LED INDICATORS
Power ON
Wiring Fault
Alarm
CONDITION
On Off Off Normal
On On/Off Two Beeps Utility Failure- The UPS is providing power to battery power-supplied
outlets from its battery.
On On/Off Rapid Beeps Utility Failure- The UPS is providing battery power. Rapid beeps
indicate the unit will run out of power shortly.
Off On/Off Long Beep
Battery Overload- Occurs when connected equipment exceeds the rating
of battery outlets of the unit. Turn the UPS off, unplug at least one piece
of equipment from battery outlets, wait 10 seconds, reset the circuit
breaker and turn the unit on.
On/Off On None
Electrical Wiring Fault- This indicates a wiring problem with the AC
outlet such as bad ground, missing ground or reversed wiring. User is
advised to disconnect all electrical equipment from the outlet and have an
electrician check the outlet to insure proper wiring.
Limited Warranty and Connected Equipment Guarantee
In purchasing a CP550SL / AE550 in the United States or Canada, the original end user receives a Limited Warranty and Connected
Equipment Guarantee from Cyber Power Systems (USA), Inc. (for ease of reading, referred to as "CyberPower"). The Limited Warranty and
the Connected Equipment Guarantee are intended to be the original end-user's exclusive rights and remedies. The Limited Warranty and
the Connected Equipment are separate, all though they are related.
Limited Warranty. The original end user (referred to as the "Initial Customer") receives an express limited warranty (referred to as the
"Limited Warranty") for the CP550SL / AE550 purchased from CyberPower (referred to as the "Product"). The Limited Warranty is for the
Product itself. The terms of the Limited Warranty are explained below.
Connected Equipment Guarantee. CyberPower also provides the Initial Customer with protection in the event that the Product is not free
from defects in materials and workmanship, and certain equipment connected to the Product is damaged (the "Connected Equipment
Guarantee"). The Connected Equipment Guarantee protects the Initial Customer for damage to equipment plugged into the Product. The
terms of the Connected Equipment Guarantee are explained below.
The Limited Warranty and the Connected Equipment Guarantee are subject to the terms set forth below. Additionally, State or Provincial law
may adjust the terms of the Limited Warranty or the Connected Equipment Guarantee or the State or Province may impose additional
obligations, or additional "implied warranties." To the extent necessary to comply with those laws, the terms of the Limited Warranty and the
Connected Equipment Guarantee should be read to adjust to those requirements only to the extent necessary to comply with such local law.
If you are an Initial Customer, you are asked to read the following terms and conditions carefully before using the Product. By using the
Product you consent to be bound by and become a party to the Limited Warranty and Connected Equipment Guarantee. If you do not agree
to the terms and conditions of the Limited Warranty and Connected Equipment Guarantee, you should return the Product for a full refund
prior to using it.
REGISTRATION
CyberPower requests that you complete and return the Warranty Registration Card enclosed with the Product or register the Product at its
website (www.cyberpowersystems.com) to establish that you are the Initial Customer of the Product, and therefore entitled coverage under
the Limited Warranty and the Connected Equipment Guarantee. (Registration is not required for Limited Warranty coverage, but note, if you
do not complete a registration card you will be required to provide proof of purchase, as described below, to have the benefits of this Limited
Warranty.)
LIMITED WARRANTY
CyberPower warrants to you, the Initial Purchaser, that the Product will be free from defects in material and workmanship for three years
from the date of original purchase, subject to the terms of this Limited Warranty.
Any Implied Warranty of Merchantability or for Fitness for a Particular Purpose, if applicable to the Product, is limited in duration to the period
of ownership by the Initial Customer. This provision shall NOT create any Implied Warranty or Merchantability or of Fitness for a Particular
Purpose that would not otherwise apply to the Product. NOTE: Some States do not allow limitations on how long an implied warranty
lasts, so the above limitation may not apply to you.
To be covered you must still be the owner of the Product at the time of the failure that results in the claim made under this Limited Warranty.
Exclusive Remedies Under Limited Warranty.
Your exclusive remedy and CyberPower's' sole obligations are as follows for the Product:
If (a) the CyberPower Product you purchased and still own is defective in material or workmanship under this Limited Warranty or any
applicable warranty imposed by law, and
(b) all Limited Warranty requirements have been met, CyberPower will repair or replace the
Product if it proves to be defective in material or workmanship during the Warranty Period.
Making a Limited Warranty Claim.
To make a Limited Warranty claim on a Product, you must do the following:
1. Complete and return the CyberPower Warranty Registration Card, or provide reasonable proof of purchase (for example, a sales receipt)
that establishes you as the Initial Customer (the original end-user consumer purchaser) of the Product and prove that the Product was
purchased within three (3) years of the event for which you want to make a claim for warranty service.
2. Call CyberPower at (952) 403-9500 or (877) 297-6937 (toll free), write to CyberPower at 5555 12th Ave. East, Suite 110, Shakopee, MN
55379, or e-mail CyberPower at claims@cyberpowersystems.com, within ten (10) days of the event for which you want to make a claim.
3. When you contact CyberPower, identify the Product, the Purchase Date, and request Return Materials Authorization (RMA) information
from CyberPower.
4. Pack and ship the Product to CyberPower as instructed in your RMA. Show the RMA code on the shipping label or include it with the
Product. You MUST prepay all shipping costs and you are responsible for packaging and shipment.
CyberPower will inspect and examine the Product within ten (10) days of receipt. If the Product is not as warranted, CyberPower will repair
or replace the Product and return it to you at CyberPower's expense, or, if CyberPower is unable to or decides not to repair or replace the
Product (if defective) within a reasonable time, CyberPower will refund to you the full purchase price you paid for the Product (purchase
receipt showing price paid is required).
CONNECTED EQUIPMENT GUARANTEE
If you are the Initial Purchaser and the Product is still covered by the Limited Warranty, the Connected Equipment Guarantee provides
protection for damage to equipment connected to the Product ("Connected Equipment"), subject to certain terms and limitations.
The Connected Equipment Guarantee is not "first dollar" coverage. It is secondary. If you have any other source of payment for your loss,
such as insurance, another warranty, or an extended warranty or purchase protection plan (“Primary Coverage”), CyberPower’ will pay only
to the extent that that the Primary Coverage does not cover the loss. CyberPower's obligation is reduced by any amounts that you are
entitled to recover from the Primary Coverage, whether or not you make a claim for recovery under any applicable Primary Coverage.
The Limited Warranty does not cover Connected Equipment, but as is explained below, to be covered under the Connected Equipment
Guarantee, the Connected Equipment must have been damaged due to a failure of the Product. The Connected Equipment must have been
damaged due to a defect in materials or workmanship of the Product.
In the event of damage to the Connected Equipment, your exclusive remedies, and CyberPower’s sole obligations, are as follows for
Connected Equipment. If (a) the Product purchased and owned by you is defective in material or workmanship; (b) the Limited Warranty
requirements have been met (except that the three year limitation of the Limited Warranty does not limit the Connected Equipment
Guarantee, which is for the lifetime of the Product), and; (c) none of the limitations or exclusions on warranty coverage apply (or than the
three year limit), CyberPower will (as CyberPower elects, as permitted by law), repair, replace, or pay the Agreed Damage Amount (defined
below) for, the item(s) of your electronic equipment directly and properly connected to the product (the "Connected Equipment") if that
Connected Equipment is (x) damaged by AC power line transients, spikes, or surges on properly installed, grounded, and code-compliant
120 volt power lines in the United States and Canada, or by transients, surges or spikes on standard telephone equipment lines, or Base
10/100T Ethernet lines that are properly installed and connected (a "Power Disturbance") and (y) is directly plugged into and properly
connected to a CyberPower Product in its original condition which is properly operated when a Power Disturbance passes through the
CyberPower Product and (y.1) exhausts the protection capacity of the CyberPower Product or (y.2) damages the CyberPower Product. This
provision sets out the only liability of any character of CyberPower for direct, indirect, special, consequential, and/or incidental damages
under our Limited Warranty, applies only to Connected Equipment, and all such Liability is limited to the Agreed Damage Amount.
Making a Connected Equipment Guarantee Claim.
To make a Warranty claim for damage to Connected Equipment under the Connected Equipment Guarantee, you must do the following:
1. Complete and return the CyberPower Warranty card or provide reasonable proof of purchase, for example, a sales receipt that
establishes you as the original end-user consumer purchaser of the Product.
2. Call CyberPower at (952) 403-9500 or (877) 297-6937 (toll free), write to CyberPower at 5555 12th Ave East, Suite 110, Shakopee, MN
55379, or e-mail CyberPower at claims@cyberpowersystems.com within ten (10) days of the date of the event for which you wish to make a
claim for warranty service.
3. When you contact CyberPower, identify the Product, the Purchase Date, and the item(s) of Connected Equipment. Have information on all
applicable insurance or other resources of recovery/payment that are available to the Initial Customer and the name of the power utility
supplier for the location of the Connected Equipment and Request a Claim Number.
4. Pack and ship the product to CyberPower and, if requested, the item(s) of Connected Equipment, a repair cost estimate for the damage to
the Connected Equipment, and all claim forms that CyberPower provides to you. Show the Claim Number on the shipping label or include it
with the product. Initial Customer shall prepay all shipping costs, must pay the cost of the repair estimate, and is responsible for
packaging and shipment.
CyberPower’s Duties.
CyberPower will inspect and examine the Product and the item(s) of Connected Equipment (or at CyberPower's election, your written
statement and repair cost estimate for those item(s)). You must return the product for inspection.
If the damage to Connected Equipment is covered by the Connected Equipment Guarantee, CyberPower will (in addition to Limited
Warranty remedies for the CyberPower Product itself) repair (or pay the costs of repair) or replace the Connected Equipment or, at the option
of CyberPower, as permitted by law, pay to the Initial Customer the "Agreed Damage Amount" (up to the aggregate limits stated below) for
all item(s) of Initial Customer's Connected Equipment. The "Agreed Damage Amount" for all items of Initial Customer's Connected
Equipment shall be the lesser of the amount determined under Clause (1) or (2) below, reduced by any amounts described in Clause (3)
below:
1. The fair market value of the Connected Equipment as established by the lower of (a) the price list of Orion Blue Book on the date of
occurrence (or if such price list is no longer published, a published or announced price list reasonably selected by CyberPower), or (b) the
average price the same or similar items are being sold for on
E-bay, or (c) the lowest price the same or similar items can be purchased for in the United States; or
2. The aggregate ceiling amount for all Connected Equipment: CyberPower CP550SL / AE550 - $75,000.00.
3. The amount(s) of all payment you have or are entitled to receive from insurance, other warranties, extended warranties, or from other
sources or persons for the Connected Equipment or damage to such equipment so that CyberPower’s maximum liability shall be reduced to
reflect all such other payments or sources of recovery
If CyberPower replaces the connected equipment or pays to the Initial Customer the Agreed Damage Amount, the Initial Customer shall
transfer ownership of all item(s) to CyberPower without warranty by the Initial Customer, but free of lien or other interest.
CONDITIONS COMMON TO THE LIMITED WARRANTY AND THE CONNECTED EQUIPMENT GUARANTEE
The Limited Warranty and the Connected Equipment Guarantee are the only and the exclusive express warranty of CyberPower with
respect to the Product. This exclusion of other express warranties applies to written and oral express warranties.
LIMITATION: THE LIMITED WARRANTY AND THE CONNECTED EQUIPMENT GUARANTEE DOES NOT COVER
The Limited Warranty and the Connected Equipment Guarantee are intended to exclusive rights and remedies and replace any other rights,
to the extent allowed by law.
1. As to the CyberPower Product, the limited warranty does not cover or apply to: misuse, modification, operation or storage outside
environmental limits for the Products, in transit, in shipment, or in storage, damage or deterioration, improper operation or maintenance, or
use with items or equipment not designed or intended for use with the product.
2. As to Connected Equipment, the Connected Equipment Guarantee covers only damage within the specific terms of the Connected
Equipment Guarantee to Connected Equipment (and only up to the applicable aggregate ceiling amount).
3. The Connected Equipment Guarantee does not cover damage to Connected Equipment or apply if the Product has been operated in a
failure mode or not in compliance with CyberPower operating instructions and manuals, or if the Connected Equipment has been operated in
a failure mode or not in compliance with the instructions and manuals of its manufacturer/vendor.
The Limited Warranty and the Connected Equipment Guarantee Do Not Apply Unless The Initial Customer:
1. Has properly connected the Product and the Connected Equipment to properly wired and grounded outlets (including compliance with
electrical and safety codes of the most current electrical code (ANS/NFPA 70), without the use of any adapters, extension cords or other
connectors.
2. Has provided a suitable and proper environment for use and installation of the Product and Connected Equipment.
3. Has properly installed and operated the CyberPower Product and Connected equipment.
4. Has operated the Product at all times within the limitations on the Product’s VA capacity as stated in this User Manual.
CyberPower Does Not Cover or Undertake Any Liability in Any Event for Any of the Following:
1. Loss of or damage to data, records, or software or the restoration of data or records, or the reinstallation of software.
2. Damage from causes other than AC Power Line Transients, spikes, or surges on properly installed, grounded and code-compliant 120
volt power lines in the United States and Canada; transients, surges or spikes on standard telephone land lines, PBX telephone equipment
lines or Base 10T Ethernet lines, when properly installed and connected. (This exclusion applies, for example, to fluctuations in data
transmission or reception, by CATV or RF transmission or fluctuations, or by transients in such transmission.
3. Damage from any circumstance described as excluded above with respect to the product.
4. Damages from fire, flood, wind, rain, rising water, leakage or breakage of plumbing, abuse, misuse or alteration of either the product or
the Connected Equipment.
Exclusion of Consequential and Other Damages.
The sole and exclusive remedies of the Initial Customer are those provided by the Limited Warranty and Connected Equipment Guarantee.
CyberPower excludes any liability for personal injury under the Limited Warranty and Connected Equipment Guarantee. CyberPower
excludes any liability for direct, indirect, special, incidental or consequential damages, whether for damage to or loss of property [EXCEPT
FOR (AND ONLY FOR) the specific limited agreement of CYBERPOWER to provide certain warranty benefits regarding "Connected
Equipment" under the "CYBERPOWER Connected Equipment Guarantee"], loss of profits, business interruption, or loss of information or
data. NOTE: Some States or Provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation may not apply to you.
DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT OR OTHER HIGH RISK ACTIVITIES.
CyberPower does not sell the Products for use in high-risk activities. The Product is not designed or intended for use in hazardous
environments requiring fail-safe performance, including the operation of nuclear facilities, aircraft navigation or communication systems, air
traffic control, weapons systems, life support or medical applications or for use in any circumstance in which the failure of the Product could
lead directly to death, personal injury, or severe physical or property damage, or that would affect operation or safety of any medical or life
support device (collectively, "High Risk Activities"). CyberPower expressly disclaims any express or implied warranty of fitness for High Risk
Activities. CyberPower does not authorize use of any of its products use in any High Risk Activities.
ANY SUCH USE IS IMPROPER AND IS A MISUSE OF CYBERPOWER PRODUCTS.
The Limited Warranty and the Connected Equipment Guarantee are governed by the laws of the United States and the State of Minnesota,
without reference to conflict of law principles. The application of the United Nations Convention of Contracts for the International Sale of
Goods is expressly excluded.
Contact Information: CyberPower's address is 5555 12th Ave East, Suite 110, Shakopee, MN 55379 and its phone number is (952)
403-9500 or Toll-free: (877) 297-6937. CyberPower is the warrantor under this Limited Warranty. You may also contact CyberPower on the
Internet at www.cyberpowersystems.com.
Product specificaties
| Merk: | CyberPower |
| Categorie: | UPS |
| Model: | Standby CP550SL |
Heb je hulp nodig?
Als je hulp nodig hebt met CyberPower Standby CP550SL stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding UPS CyberPower
15 November 2024
7 November 2024
7 November 2024
24 September 2024
24 September 2024
24 September 2024
24 September 2024
24 September 2024
24 September 2024
24 September 2024
Handleiding UPS
- UPS HP
- UPS IKEA
- UPS AEG
- UPS Siemens
- UPS Apc
- UPS Dell
- UPS Digitus
- UPS Eaton
- UPS Emerson
- UPS Furman
- UPS Gembird
- UPS Gys
- UPS Lenovo
- UPS LevelOne
- UPS Riello
- UPS Schneider
- UPS Voltcraft
- UPS Jung
- UPS Steren
- UPS Conceptronic
- UPS Tripp Lite
- UPS Approx
- UPS Block
- UPS LC-Power
- UPS Energenie
- UPS Adj
- UPS East
- UPS Equip
- UPS Liebert
- UPS Avocent
- UPS Minute Man
- UPS Minuteman
- UPS Maruson
- UPS V7
- UPS Phoenix Contact
- UPS Puls Dimension
- UPS Vanson
- UPS Salicru
- UPS SurgeX
- UPS Murr Elektronik
- UPS Altronix
- UPS Ditek
- UPS Bxterra
- UPS Middle Atlantic
- UPS FSP
- UPS Atlantis Land
- UPS PowerWalker
- UPS FSP/Fortron
- UPS Online USV
Nieuwste handleidingen voor UPS
18 November 2024
17 November 2024
17 November 2024
17 November 2024
16 November 2024
15 November 2024
14 November 2024
14 November 2024
12 November 2024
22 Oktober 2024