CyberPower RT650EI Handleiding

CyberPower UPS RT650EI

Lees hieronder de 📖 handleiding in het Nederlandse voor CyberPower RT650EI (2 pagina's) in de categorie UPS. Deze handleiding was nuttig voor 10 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

RT650EI / RT500EI

User’s Manual

K01-0000540

-00

Thank you for purchasing a CyberPower product. Please take a few minutes to

www.c

yberpower.com/registration. Registration certifies your product's warranty, confirms your

ownership

in the event of a product loss or theft

and entitles you to free technical support.

(SAVE THESE INSTRUCTIONS)

This manual contains important instructions that should be followed during installation and maintenance of

the UPS and batteries.

CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity controlled

indoor area free of conductive contaminants. (Please see specifications for acceptable temperature and

humidity range).

CAUTION! To reduce the risk of electric shock, do not remove the cover except to service the battery.

There are no user serviceable parts inside, except for thebattery.

CAUTION! Hazardous live parts inside can be energized by the battery even when the AC input power is

disconnected.

CAUTION! The UPS must be connected to an grounded AC power outlet with fuse or circuit breaker

protection. Do not plug into an outlet that is not grounded. If you need to de-energize this equipment, turn off

and unplug the unit.

CAUTION! To avoid electrical shock, turn off the unit and unplug it form the AC power source before

servicing the battery or installing a computer component.

CAUTION! Do not dispose of batteries in a fire. The batteries may explode.

CAUTION! Do not open or mutilate batteries. Released electrolyte is harmful to the skin and eyes. It may

be toxic.

DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT! CyberPower Systems does not sell

products for life support or medical applications. DO NOT use in any circumstance that would affect

operation and safety of life support equipment, any medical applications or patient care.

DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of fire or electric shock, do not use with

or near an aquarium. Condensation from the aquarium can cause the unit to short out.

DO NOT USE THE UPS ON ANY TRANSPORTATION! To reduce the risk of fire or electric shock, do not

use the unit on any transportation such as airplanes or ships. The effect of shock or vibration caused during

transit and the damp environment can cause the unit to short out.

UNPACKING

Inspect the UPS upon receipt. The box should contain the following:

(a) UPS unit (b) User’s manual (c) USB device cable (d) IEC to IEC power cord

*PowerPanel® Personal Edition software is available on our website. Please visit

www.cyberpower.com and go to the Software Section for free download.

HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT

1. Ensure that the equipment plugged into the UPS does not exceed the UPS unit’s rated capacity

(650VA/400W for RT650EI and 500VA/300W for RT500EI). If the rated capacities of the unit are

exceeded, an overload condition may occur and cause the UPS unit to shut down or the circuit breaker to

trip.

2. There are many factors that can affect the amount of power that your electronic equipment will require.

For optimal system performance keep the load below 80% of the unit’s rated capacity.

DESCRIPTION

1. LED Indicators

The LED indicators will illuminate to show the status of power: on line, on battery, overload, replace

battery.

2. Power Switch

To turn the UPS ON, press the power button for approximately 2 seconds - you will hear a constant tone

and release after a short beep.

To turn the UPS OFF, press the power button for approximately 2 seconds - you will hear a constant

tone and release after two short beeps.

Mute mode: The audible alarm can be turned Off or On by quickly pressing the POWER button twice.

The default setting is for the Alarm On. To turn the Alarm Off, quickly press the power button twice. You

will hear two short beeps when the Alarm is turned Off. To turn the Alarm back On, quickly press the

power button twice. You will hear a single short beep when the Alarm is turned On. *When the Alarm is

turned Off, there will be no audible notification when the UPS goes to Battery mode or reaches a low

battery state.

3. Communication Protection Ports

Communication protection ports will protect any standard modem, fax, telephone line, network or

Ethernet connection (RJ11/RJ45).

4. USB Port to PC

The USB port allows connection and communication between the USB port on the computer and the

UPS unit. The UPS communicates its status to the PowerPanel® Personal Edition software.

5. Communication Port to PC

This port allows connection and communication between the UPS and computer. The UPS

communicates its status to the PowerPanel® Personal Edition software. For information regarding

ordering a serial cable for the unit, please contact technical support at CyberPower System.

NOTE: Only one of communication port and USB port can be used as communication and control of the

UPS unit at one time.

6. Battery and Surge Protected Outlets

The unit has battery powered/surge suppression outlets to ensure temporary uninterrupted operation of

your equipment during a power failure. (DO NOT plug a laser printer, paper shredder, copier, space

heater, vacuum cleaner, sump pump, or other large electrical device into the “Battery and Surge

Protected Outlets.” The power demands of these devices will overload and possibly damage the

unit.)

7. Circuit Breaker

Located on the back of the UPS, the circuit breaker serves to provide overload and fault protection.

8. AC Input

Connect the AC Power cord to a properly wired and grounded outlet.

1. Your new UPS may be used immediately upon receipt. However, after receiving a new UPS, to ensure

the battery’s maximum charge capacity, it is recommended that you charge the battery for at least 8

hours. Your UPS is equipped with an auto-charge feature. When the UPS is plugged into an AC outlet,

the battery will automatically charge when it’s turned on or turned off.

Note: This UPS is designed with a safety feature to keep the system from being turned on during

shipment. The first time you turn the UPS on, you will need to have it connected to AC power or it

will not power up.

2. With the UPS unit turned off and unplugged, connect your computer, monitor, and any other peripherals

requiring battery backup from the SURGE & BATTERY outlets. DO NOT plug a laser printer, paper

shredder, copier, space heater, vacuum cleaner, sump pump, or other large electrical device into

the “Battery and Surge Protected Outlets”. The power demands of these devices will overload

and possibly damage the unit.

3. To protect a fax, phone, or modem line, connect a telephone cable from the wall jack outlet to the IN jack

of the UPS. Connect a telephone cable from the UPS OUT jack to protect a modem port on the computer,

a telephone, or fax machine.

4. Plug the UPS into a 2 pole, 3 wire grounded receptacle (wall outlet). Make sure the wall branch outlet is

protected by a fuse or circuit breaker and does not service equipment with large electrical demands (e.g.

air conditioner, refrigerator, copier, etc.). The warranty prohibits the use of extension cords, outlet strips,

and surge strips in conjunction with the UPS unit.

5. If an overload is detected, an audible alarm will sound and the unit will emit one long beep. To correct this,

turn the UPS off and unplug at least one piece of equipment from the battery power supplied outlets.

Make sure the circuit breaker is depressed and then turn the UPS on.

6. To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times.

7. To store the UPS for an extended period of time, cover it and store with the battery fully charged. While in

storage, recharge the battery every three months to ensure optimal battery life.

8. Ensure the wall outlet and UPS are located near the equipment being attached for

proper accessibility.

9. The UPS can lie down on the left direction during operation. DO NOT lie down on

the other side which may block the ventilation hole and hinder the heat dissipation.

CAUTION! Read and follow the IMPORTANT SAFETY INSTRUCTIONS before servicing the battery.

Service the battery under the supervision of personnel knowledgeable of batteries and their

precautions.

CAUTION! Use only the specified type of battery. See your dealer for replacement batteries.

CAUTION! The battery may present the risk of electrical shock. Do not dispose of batteries in a fire, as they

may explode. Follow all local ordinances regarding proper disposal of batteries.

CAUTION! Do not open or mutilate the batteries. Released electrolyte is harmful to the skin and eyes and

may be toxic.

CAUTION! A battery can present a high risk of short circuit current and electrical shock. Take the following

precautions before replacing the battery:

1. Remove all watches, rings or other metal objects.

2. Only use tools with insulated handles.

3. DO NOT lay tools or other metal parts on top of battery or any battery terminals.

4. Wear rubber gloves and boots.

5. Determine if the battery is inadvertently grounded. If inadvertently grounded, remove source of ground.

CONTACT WITH A GROUNDED BATTERY CAN RESULT IN ELECTRICAL SHOCK! The likelihood of

such shock will be reduced if such grounds are removed during installation and maintenance (applicable to a

UPS and a remote battery supply not having a grounded circuit)

 TO REPLACE THE BATTERY

1. Turn off and unplug all connected equipment.

2. Unplug it from the AC power source.

3. Turn the UPS on its side.

4. Remove the retaining screw.

5. Slide the battery compartment cover completely off of the unit.

6. Remove the battery from the compartment.

7. Disconnect the battery wires from the battery.

8. Install the replacement battery by connecting the red wire and black wire to the positive (+) and

negative (-) terminal of the battery.

9. Put the battery back into the compartment.

10. Slide back the battery compartment cover and tighten the retaining screw.

11. Charge the unit for 8 hours to fully charge the battery.

BASIC OPERATION

INSTALLING YOUR UPS SYSTEM

IMPORTANT SAFETY INSTRUCTIONS

PRODUCT REGISTRATION

HARDWARE INSTALLATION GUIDE

REPLACING THE BATTERY

DEFINITIONS FOR ILLUMINATED LED INDICATORS

Line

Battery

Overload

Replace

Battery

Alarm

CONDITION

Off

Off Off

Off

Normal

Off

Off Off

Beep twice

every 30

seconds

Utility Failure- The UPS is providing

power to battery protected outlets

from its battery.

Off

Flash

Off Off

Rapid

Beeping

every 1/2

second

Utility Failure - The UPS is

providing battery power. Rapid

beeping indicates the unit will run out

of power shortly.

Off

One Flash

every 5

seconds

Off

Constant

tone

Overload Fault - Occurs when

connected equipment exceeds the

listed capacity of the UPS. Turn the

UPS off, unplug at least one piece of

equipment from battery outlets, wait

10 seconds, reset the circuit breaker

and turn the unit on.

Off

On/Flash

Off

onstant

tone

Short Fault (two flashes every 5

seconds

) -

Unplug at least one piece

of equipment from battery outlets

and turn the UPS on again.

UPS Fault

(constantly illuminate)

Contact CyberPower Systems for

support.

On/Off

Off/On

Flash

Off

Beep every

one second

Charger Fault (three flashes every 5

seconds

) - Contact CyberPower

Systems for support.

Off

Flash

Beep every

two

seconds in

30 seconds

Battery is worn out or

disconnected

– Make sure the

battery is connected or replace a

new battery.

CyberPower’s Green Commitment

CyberPower is dedicated to the development of green products, and has adopted

Green practices throughout its business, including: membership in Climate Savers

Computing Initiative (CSCI), accordance with the Restriction on Hazardous Substances

(RoHS), Waste Electrical and Electronic Equipment (WEEE) protocols, as well as ISO

14001 and IECQ QC080000. CyberPower pledges to provide the advanced energy

solution for the environment and become a leading eco-friendly organization in the UPS

industry.

Reduce Energy Cost with GreenPower UPSTM Technology

CyberPower’s goal is not only to provide eco-friendly products but also to bring the best value for consumers.

The advanced energy-saving design improves the operating efficiency and eliminates waste energy

consumption. As a result, consumers will enjoy significant energy cost savings with the adoption of

GreenPower UPSTM

technology.

In line mode, the AC input voltage may not be stable all the time, to prevent the connected equipment

from damage caused by the unexpected voltage fluctuations, please adjust the sensitivity of the unit

by the steps as follows:

1. Please make sure that the UPS is in LINE MODE.

2. To Enter the Sensitivity Setup mode, press the Power Button for 10 seconds until all indicators flash 2

seconds rapidly.

3. The unit will show the current sensitivity setting, as shown in the following table.

4. To select Low Sensitivity setting: shortly press power button until one red indicator (the last one)

illuminate.

5. To select Medium Sensitivity setting, press the power button until both red indicators (the third and fourth

from the top) illuminate.

6. To select High Sensitivity setting, press the power button until yellow and both red indicators (bottom

three) illuminate.

7. To set up a level of sensitivity, hold down the power button until the green indicator (the first one)

illuminates.

8. Once in setup mode, if there is no action within 5 seconds, the unit will exit setup mode and no setting is

done.

Indicators

Illuminate

Sensitivity

Input Voltage

Range

Description

(Red) Low

176 – 272 Vac

If the connected equipment can tolerate more power

events (example: unstable power often associated

with stormy weather), select Low Sensitivity and the

UPS will go to Battery Mode less often.

(Red, Red)

Medium

(Default)

192 – 264 Vac

The UPS will go to Battery Mode if the input voltage

is beyond the range.

(Yellow, Red,

Red)

High

200 – 254 Vac

If the connected equipment is more sensitive to

power events, select High Sensitivity and the UPS

will go to Battery Mode more often.

Problem

Possible Cause

Solution

Circuit breaker button is

projecting from the back of

the unit.

Circuit breaker has been

tripped due to an overload.

Turn the UPS off and unplug at least one

piece of equipment. Wait 10 seconds, reset

the circuit breaker by pressing the button,

and then turn the UPS on.

The UPS does not perform

expected runtime.

Battery not fully charged.

Recharge the battery by leaving the UPS

plugged in.

Battery is worn out.

Please contact CyberPower Systems about

replacement batteries.

The UPS will not turn on.

The on/off switch is

designed to prevent

damage from rapidly

turning it off and on.

Turn the UPS off.

Wait 10 seconds and then

turn the UPS on.

The unit is not connected

to an AC outlet.

The unit must be connected to a 230V

50/60Hz outlet.

The battery is worn out.

Please contact CyberPower Systems about

replacement batteries.

Mechanical problem.

Please c

ontact CyberPower Systems.

The frequency is outside of

the operating range of

50/60±3Hz.

Turn the UPS off. Make sure the frequency

range is within

50/60±3

Hz. Or you can turn

the UPS on in battery mode.

PowerPanel

® Personal

Edition is

inactive (all icons

are gray).

The USB cable is not

connected.

Connect the USB / serial cable to the UPS

unit and an open USB / serial port on the

back of the computer. You must use the

cable that came with the unit.

NOTE:

Only one of communication port

and

USB port

can be used as communication and

control of the UPS unit at one time.

The USB cable is

connected to a bad USB

port.

Check for a different USB port and plug the

cable in

The unit is not providing

battery power.

Shutdown your computer and turn the UPS

off.

Wait 10 se

conds and turn the UPS back

on. This should reset the unit.

Additional troubleshooting information can be found at “Support” at www.cyberpower.com

Model

RT500EI

RT650EI

Capacity

500 VA / 300W

650 VA / 400W

Input

Nominal Input Voltage

230Vac

Input Frequency

50/60Hz ± 3Hz

Ouput

On-Battery Output Voltage

230Vac ± 10%

On-Battery Output Frequency

50/60Hz ± 1% (Auto-sensing)

On-Battery Output Wave Form

Simulated Sine wave

Status Indicators

Indicators

On Line, On Battery, Overload, Replace Battery

Audible Alarms

On Battery, Low Battery, Overload

Environment

Operating Temperature

32°F to 113° F / 0° C to 45° C

Operating Relative Humidity

0 to 95% non-condensing

Physical

Size (W x H x D)

3.6” x 6.5” x 11.0”

Net Weight

4.08 kg

4.58 kg

Battery

Sealed Maintenance Free Lead Acid Battery

User Replaceable

Yes

Typical Battery Recharge Time

8 hours typical from total discharge

Typical Battery Life

3 to 6 years, depending on number of discharge/recharge cycles

Communication

PowerPanel® Personal Edition

Software

Windows 10 / 8 / 7 / Vista / XP / 2000, Server2012 / 2008 / 2003,

Linux

Certification

For more information, visit www.cyberpower.com

Manufacturer: Cyber Power Systems Inc.

6F, No.32, Sec.1, Chenggong Rd.Nangang District, Taipei 115, Taiwan

TECHNICAL SPECIFICATIONS

TROUBLESHOOTING

FUNCTION SETUP GUIDE – SENSITIVITY SETUP

CYBERPOWER GREENPOWER UPS™ TECHNOLOGY

Product specificaties

Merk:	CyberPower
Categorie:	UPS
Model:	RT650EI
Kleur van het product:	Zwart
Gewicht:	4650 g
Breedte:	91.4 mm
Diepte:	279.4 mm
Hoogte:	165.1 mm
Snoerlengte:	1.83 m
Gewicht verpakking:	5200 g
Breedte verpakking:	382 mm
Diepte verpakking:	154 mm
Hoogte verpakking:	217 mm
Materiaal behuizing:	Kunststof
LED-indicatoren:	Status, Battery replacement
Vormfactor:	Tower
USB-poort:	Ja
Meegeleverde kabels:	Input power cable, USB cable
Aantal USB 2.0-poorten:	1
Soort serieële aansluiting:	RS-232
Aantal Ethernet LAN (RJ-45)-poorten:	1
Ondersteund aantal accu's/batterijen:	1
Certificering:	CE
RS-232 port:	1
Geluidsalarm(en):	Ja
Responstijd:	10 ms
Duurzaamheidscertificaten:	RoHS
Meegeleverde software:	PowerPanel Personal Edition
Uitgangsvermogen:	400 W
Accu/Batterij oplaadtijd:	8 uur
Temperatuur bij opslag:	-15 - 45 °C
Stroomspanning bescherming:	Overbelasting
Frequentie:	50/60 Hz
Luchtvochtigheid bij opslag:	0 - 95 procent
Hoogte, in bedrijf:	0 - 3000 m
Hoogte bij opslag:	0 - 15000 m
Modem (RJ-11) poort:	1
Stekker:	C14 stekker
Bedrijfstemperatuur (T-T):	0 - 45 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 95 procent
Batterijtechnologie:	Sealed Lead Acid (VRLA)
Code geharmoniseerd systeem (HS):	85078000
Surge energy rating:	810 J
Aantal AC uitgangen:	4 AC-uitgang(en)
Stopcontacttypes:	C13 stekker
Stroom (max.):	5 A
Output power capacity:	0.65 kVA
Ingang operation voltage (min):	192 V
Ingang operation voltage (max):	264 V
Uitgang operation voltage (min):	230 V
Uitgang operation voltage (max):	230 V
UPS-topologie:	Stand-by (Offline)
Aantal input fases:	1
Typische backup tijd op halve lading:	15 min
Typische backup tijd op volledige lading:	5 min
Hot-swap batterij:	Ja
Seriële interface:	Ja
Hoorbare alarmstanden:	Fault, Low battery alarm, Overload alarm
Output voltage THD:	5 procent
Aantal output fases:	1
EMI/RFI geluidsfiltering:	Ja
Spanningsbeveiliging:	Ja
Golfvorm:	Sinus
Uitgangsfrequentieregeling:	50/60 Hz