CyberPower PR5000ELCDRTXL5U Handleiding

CyberPower UPS PR5000ELCDRTXL5U

Lees hieronder de 📖 handleiding in het Nederlandse voor CyberPower PR5000ELCDRTXL5U (12 pagina's) in de categorie UPS. Deze handleiding was nuttig voor 2 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/12

User’s Manual

PR5000ELCDRTXL5U

PR6000ELCDRTXL5U

K01-0000166-01

This manual contains important instructions. Please read and follow all instructions carefully during installation and operation of the unit. Read this manual

thoroughly before attempting to unpack, install, or operate the UPS.

CAUTION! The UPS must be connected to a grounded AC power

outlet with fuse or circuit breaker protection. DO NOT plug the UPS into

an outlet that is not grounded. If you need to power-drain this

equipment, turn off and unplug the unit.

CAUTION! The battery can power hazardous components inside the

unit, even when the AC input power is disconnected.

CAUTION! The UPS should be near the connected equipment and

easily accessible.

CAUTION! To prevent the risk of fire or electric shock, install in a

temperature and humidity controlled indoor area, free of conductive

contaminants. (Please see specifications for acceptable temperature and

humidity range).

CAUTION! To reduce the risk of an electric shock, do not remove the

cover, except to service the battery. There are no user serviceable parts

inside, except for the battery.

CAUTION! To avoid electrical shock, turn off the unit and unplug it from

the AC power source before servicing the battery or installing a computer

component.

CAUTION! To reduce the risk of fire, connect the UPS to a circuit with

30 amperes maximum over-current protection in accordance to CE

requirement.

CAUTION! The AC outlet where the UPS is connected should be close to

the unit and easily accessible.

CAUTION! Please use only VDE-tested, CE-marked mains cable, (e.g.

the mains cable of your equipment), to connect the UPS to the AC outlet.

CAUTION! Please use only VDE-tested, CE-marked power cables to

connect any equipment to the UPS.

CAUTION! When installing the equipment, ensure that the sum of the

leakage current of the UPS and the connected equipment does not

exceed 3.5mA.

CAUTION! This is permanently connected equipment and only qualified

maintenance personnel may carry out installations.

CAUTION! Do not unplug the unit from AC Power during operation, as

this will invalidate the protective ground insulation.

CAUTION! To avoid electrical shock, turn off and unplug the unit first,

then install the input/output power cord with grounded. Connect the

ground wire prior to connecting the line wires!

CAUTION! Do not use improper size power cord to avoid damaging your

equipment and avoid fire hazards.

CAUTION! Wiring must be done by qualified personnel.

CAUTION! DO NOT USE FOR MEDICAL OR LIFE SUPPORT

EQUIPMENT! Under no circumstances this unit should be used for

medical applications involving life support equipment and/or patient care.

CAUTION! DO NOT USE WITH OR NEAR AQUARIUMS! To reduce

the risk of fire, do not use with or near aquariums. Condensation from

the aquarium can come in contact with metal electrical contacts and

cause the machine to short out.

DO NOT INSTALL THE UPS WHERE IT WOULD BE EXPOSED TO

DIRECT SUNLIGHT OR NEAR A STRONG HEAT SOURCE!

DO NOT BLOCK OFF VENTILATION OPENINGS AROUND THE

HOUSING!

DO NOT CONNECT DOMESTIC APPLIANCES SUCH AS HAIR

DRYERS TO UPS OUTPUT SOCKETS

UNPACKING

UPS

unit

Rack mount ears (Stands) (2)

IMPORTANT SAFETY INSTRUCTIONS

Rack mount ear & rails screws (34)

User’s manual

Screw hole dust covers (8)

Rack mount rails (1 set – left and

right sides)

Front panel

Input/ Output terminal cover

AUTOMATIC VOLTAGE REGULATOR(AVR)

The PR5000ELCDRTXL5U/ PR6000ELCDRTXL5U stabilizes damaging inconsistent utility power. The

Automatic Voltage Regulator automatically regulates low or high voltages to keep equipment working at safe AC

power levels (220/230/240V) without switching to battery. Your equipment operates normally when power

problems, such as, shout brownouts and blackouts. The unit’s powerful sealed lead-acid batteries will provide

power during the incoming voltage drops below 151V or increases above 302V.

SYSTEM BLOCK DIAGRAM

HARDWARE INSTALLATION GUIDE

Battery charge loss may occur during shipping and storage.

Before using the UPS, it’s strongly recommended to charge batteries

for four hours typically to ensure that the batteries’ maximum charge

capacity is met. To recharge the batteries, simply plug the UPS into

an AC outlet.

When using the included software, connect either the serial or the

USB cable between the computer and the corresponding port on the

UPS. Note: If the USB port is used, the serial port will be disabled.

They cannot be used simultaneously. The computer with the

PowerPanel

Business Edition Agent software connects to the USB

port or the Serial port on the UPS. It can control the operating

schedule, battery test, outlet, etc. and obtain information on the UPS

status. However, other computers with PowerPanel

Business Edition

Client software can only obtain UPS status information via a LAN

connection.

With the UPS off and unplugged, connect your computer, monitor,

and any externally powered data storage device (Hard drive, Tape

drive, etc.) into the outlets. DO NOT plug a laser printer, copier,

space heater, vacuum, paper shredder or other large electrical device

into the UPS. The power demands of these devices will overload and

possibly damage the unit.

To protect a fax, telephone, modem line or network cable, connect

the telephone or network cable from the wall jack outlet to the jack

marked “IN” of the UPS. Then, connect a telephone cable or network

cable from the jack marked “OUT” on the UPS to the modem,

computer, telephone, fax machine, or network device.

Press the power switch to turn the UPS on. The Power-On

indicator light will illuminate. If an overload is detected, an audible

alarm will sound and the UPS will emit one long beep. In order to

reset it, turn the unit off and unplug some equipment from outlets.

Make sure your equipment carry a load current within the unit’s safe

range, (refer to the technical specifications), and then turn the unit on.

Your UPS is equipped with an auto-charge feature. When the UPS

is plugged into an AC outlet, the battery will automatically charge,

even when the unit is switched off.

To maintain an optimal battery charge, leave the UPS plugged into

an AC outlet at all times.

Before storing the UPS for an extended period of time, turn the

unit OFF. Then cover it and store it with the batteries fully charged.

Recharge the batteries every three months to ensure good battery

capacity and long battery life. Maintaining a good battery charge will

help prevent possible damage to the unit from battery leakage.

The unit has one Primary Serial Port (I), one Secondary Serial

Port (II), and one USB port, (paired with the Primary Serial Port), to

allow connection and communication between the unit and any

attached computers. The Primary Serial Port (I) as well as its paired

USB port allow for bi-directional communication among the UPS and

the primary connected computer running the PowerPanel

Business

Edition Agent software. The UPS can control the computer’s

shutdown in case of an emergency, and at the same time, the

computer can monitor the UPS and alter its various programmable

parameters. On the other hand, secondary Serial Port II, only allows

the UPS to initiate the connected computer’s (installed the

PowerPanel

Personal Edition software) graceful shutdown in case of

an emergency. If necessary, please download PowerPanel

Personal

Edition software at www.cpsww.com. DO NOT install PowerPanel

Business Edition Agent and PowerPanel

Personal Edition software

on the same computer.

10.

EPO (Emergency Power Off) Port:

Use the provided gray cable to connect to a special EPO contact

switch. Follow the appropriate circuit diagram below to wire the

cable to your EPO configuration. The EPO remote switch is a switch

installed in an outside area, connected to the unit via an ordinary

RJ-11 phone line. In case of an emergency, it can be used to

immediately cut off power from the UPS unit.

11.

To avoid electrical shock, before hardwiring the UPS (in/out

power cord), turn the unit OFF and disconnect the unit from utility

power. The in/out power cord MUST be grounded.

INSTALLING YOUR UPS SYSTEM

Product specificaties

Merk:	CyberPower
Categorie:	UPS
Model:	PR5000ELCDRTXL5U
Kleur van het product:	Zwart
Gewicht:	101500 g
Breedte:	433 mm
Diepte:	645 mm
Hoogte:	220 mm
LED-indicatoren:	Stroom
Vormfactor:	Rackmontage/toren
USB-poort:	Ja
Accu/Batterij voltage:	12 V
Aantal USB 2.0-poorten:	1
Soort serieële aansluiting:	RS-232
Aantal Ethernet LAN (RJ-45)-poorten:	1
Ondersteund aantal accu's/batterijen:	16
Certificering:	CE, C-Tick, EAC
RS-232 port:	1
Geluidsalarm(en):	Ja
Responstijd:	4 ms
Duurzaamheidscertificaten:	RoHS
Meegeleverde software:	PowerPanel Business Edition
Uitgangsvermogen:	4000 W
Batterij capaciteit:	9 Ah
Temperatuur bij opslag:	-15 - 45 °C
Stroomspanning bescherming:	Overspanning
Frequentie:	50/60 Hz
Luchtvochtigheid bij opslag:	0 - 95 procent
Stekker:	Eindstation
Rackcapaciteit:	5U
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 95 procent
Batterijtechnologie:	Sealed Lead Acid (VRLA)
Type beeldscherm:	LCD
Surge energy rating:	810 J
Aantal AC uitgangen:	11 AC-uitgang(en)
Stopcontacttypes:	C13 coupler, C19 coupler
Stroom (max.):	40 A
Output power capacity:	5 kVA
Ingang operation voltage (min):	159 V
Ingang operation voltage (max):	288 V
Uitgang operation voltage (min):	220 V
Uitgang operation voltage (max):	240 V
UPS-topologie:	Line-interactive
Typische backup tijd op halve lading:	31 min
Typische backup tijd op volledige lading:	12 min
Hot-swap batterij:	Ja
Hoorbare alarmstanden:	Low battery alarm, Overload alarm
Emergency Power Off (EPO):	Ja
EMI/RFI geluidsfiltering:	Ja
Golfvorm:	Sinus
Noodstop-aansluiting (EPO):	Ja
Uitgangsfrequentieregeling:	50/60 Hz
Automatic Voltage Regulation (AVR):	Ja