CyberPower OR1000LCDRM1U Handleiding

CyberPower UPS OR1000LCDRM1U

Lees hieronder de 📖 handleiding in het Nederlandse voor CyberPower OR1000LCDRM1U (2 pagina's) in de categorie UPS. Deze handleiding was nuttig voor 18 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

OR1000LCDRM1U / OR1500LCDRM1U

User’s Manual

K01-0000053-01

(SAVE THESE INSTRUCTIONS)

This manual contains important instructions that should be followed during installation and maintenance of the UPS and batteries. Please

read and follow all instructions carefully during installation and operation of the unit. Read this manual thoroughly before attempting to

unpack, install, or operate.

CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity controlled indoor area, free of conductive

contaminants. (Please see specifications for acceptable temperature and humidity range).

CAUTION! To reduce the risk of electric shock, do not remove the cover, except to service the battery. There are no user serviceable parts

inside, except for the battery.

CAUTION! The battery can energize hazardous live parts inside even when the AC input power is disconnected.

CAUTION! The UPS must be connected to a grounded AC power outlet with fuse or circuit breaker protection. DO NOT plug the UPS into

an outlet that is not grounded. If you need to de-energize this equipment, turn off and unplug the UPS.

CAUTION! To avoid electrical shock, turn off the unit and unplug it from the AC power source before servicing the battery or installing a

computer component.

CAUTION! DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT! CyberPower Systems does not sell products for life support

or medical applications. DO NOT use in any circumstance that would affect the operation or safety of any life support equipment, with any

medical applications, or patient care.

CAUTION! DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of fire, do not use with or near aquariums. Condensation from

the aquarium can come in contact with metal electrical contacts and cause the machine to short out.

DO NOT USE THE UPS ON ANY TRANSPORTATION! To reduce the risk of fire or electric shock, do not use the unit on any transportation

such as airplanes or ships. The effect of shock or vibration caused during transit and the damp environment can cause the unit to short out.

INTRODUCTION

Thank you for selecting a CyberPower Systems UPS product. This UPS is designed to provide unsurpassed power protection, operation and

performance during the lifetime of the product.

UNPACKING

Inspect the UPS upon receipt. The box should contain the following:

(a) UPS unit (b) User’s manual (c) Rack mount brackets (d)Telephone cable (e) PowerPanel® Business Edition software CD (f) Serial interface

cable (DB-9) (g) USB A+B type cable (h) Warranty registration card

OVERVIEW

The OR1000LCDRM1U/OR1500LCDRM1U UPS provides complete power protection from utility power that isn't always consistent. The

OR1000LCDRM1U/OR1500LCDRM1U features surge protection against power surges and

maintenance free batteries for long lasting battery backup during power outages. In addition to

ensuring consistent power to your computer system and the OR1000LCDRM1U/OR1500LCDRM1U

also includes software that will automatically save your open files and shutdown your computer

system during a utility power loss.

AUTOMATIC VOLTAGE REGULATOR

The OR1000LCDRM1U/OR1500LCDRM1U stabilizes inconsistent utility power voltage to nominal

levels that are safe for equipment. Inconsistent utility power may be damaging to important data files

and hardware, but with Automatic Voltage Regulation (AVR), damaging voltage levels are corrected

to safe levels. AVR automatically increases low utility power or decreases high utility power to a

consistent and safe 110/120 volts.

HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT

1. Ensure that the equipment plugged into the outlets does not exceed the UPS unit’s rated capacity (1000VA/600W for OR1000LCDRM1U,

1500VA/900W for OR1500LCDRM1U). If the rated capacities of the unit are exceeded, an overload condition may occur and cause the

UPS unit to shut down or the circuit breaker to trip.

HARDWARE INSTALLATION GUIDE

1. Your new UPS may be used immediately upon receipt. However, recharging the battery for at least eight hours is recommended to ensure

that the battery's maximum charge capacity is achieved. Charge loss may occur during shipping and storage. To recharge the battery,

simply leave the unit plugged into an AC outlet. The unit will charge in both the on and off position.

2. If you will use the software, connect the USB cable to the USB port on the UPS.

3. With the UPS unit off and unplugged, connect the computer, monitor, and any externally powered data storage device (Zip drive, Jazz drive,

Tape drive, etc.) into the battery power supplied outlets. DO NOT plug a laser printer, copier, space heater, vacuum, paper shredder or

other large electrical device into the UPS. The power demands of these devices will overload and

possibly damage the unit.

4. To protect a fax, telephone, modem line or network cable, connect a telephone cable or network cable from

the wall jack outlet to the IN jack of the UPS. Then connect a telephone cable or network cable from the

OUT jack on the UPS to the modem, computer, telephone, fax machine, or network device.

5. Plug the UPS into a 2 pole, 3 wire grounded receptacle (wall outlet). Make sure the wall branch outlet is

protected by a fuse or circuit breaker and does not service equipment with large electrical demands (e.g.

air conditioner, refrigerator, copier, etc.). Avoid using extension cords.

6. Depress the power switch to turn the unit on. The power on indicator light will illuminate and the unit will

"beep" once.

7. If an overload is detected, an audible alarm will sound and the unit will emit one long beep. To correct this, turn the UPS off and unplug at

least one piece of equipment from the battery power supplied outlets. Wait 10 seconds. Make sure the circuit breaker is depressed and then

turn the UPS on.

8. Your UPS is equipped with an auto-charge feature. When the UPS is plugged into an AC outlet, the battery will automatically recharge.

9. To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times.

10. To store your UPS for an extended period, cover it and store with the battery fully charged. Recharge the battery every three months to

ensure battery life.

DESCRIPTION

1. LCD module display

LCD shows all the UPS information with icons and

messages.

2. Power On Indicator

This LED is illuminated when the utility condition is

normal and the UPS outlets are providing power,

free of surges and spikes.

3. Power Switch

Master on/off switch for equipment connected to

the battery power supplied outlets.

4. LCD function selected switch

The switch can be used to select the LCD display contents Including input/output voltage and estimated run time, etc.

5. Battery and Surge Protected Outlets

The unit has four battery powered/surge suppression outlets for connected equipment to ensure temporary uninterrupted operation of your

equipment during a power failure. (DO NOT plug a laser printer, paper shredder, copier, space heater, vacuum cleaner, sump pump or

other large electrical devices into the “Battery and Surge Protected Outlets”. The power demands of these devices may overload and

damage the unit.)

6. Full-Time Surge Protection Outlets

The unit has two surge suppression outlets.

7. Communication Protection Ports RJ11/RJ45

Communication protection ports will protect any standard modem, fax, telephone line, or network cable.

8. USB Port to PC

This port allows connection and communication from the USB port on the computer to the UPS unit. The UPS communicates its status to the

PowerPanel® Business Edition software.

9. Dry contact

This port produces information for equipment that can read dry contact signals.

10. Circuit Breaker

Located on the back of the UPS, the circuit breaker serves to provide overload and fault protection. Under normal operating conditions, the circuit

breaker is depressed.

11. Electrical Wiring Fault Indicator

This LED indicator will illuminate to warn the user that a wiring problem exists, such as bad ground, missed ground or reversed wiring. If this is

illuminated, disconnect all electrical equipment from the outlet and have an electrician check to ensure the outlet is properly wired.

12. AC Input

Connect the AC Power cord to a properly wired and grounded outlet.

13. SNMP/HTTP Network Slot

Remove the cover panel to install an optional RMCARD provides remote monitoring and management of your UPS over a network.

REPLACING THE BATTERY

CAUTION! IMPORTANT SAFETY INSTRUCTIONS Read and follow the before servicing the battery.

Service the battery under the supervision of personnel knowledgeable of batteries and their precautions.

CAUTION! Use only the specified type of battery. See your dealer for replacement batteries.

CAUTION! The battery may present the risk of electrical shock. Do not dispose of batteries in a fire, as they may explode. Follow all local

ordinances regarding proper disposal of batteries.

CAUTION! Do not open or mutilate the batteries. Released electrolyte is harmful to the skin and eyes and may be toxic.

CAUTION! A battery can present a high risk of short circuit current and electrical shock. Take the following precautions before replacing the

battery:

1. Remove all watches, rings or other metal objects.

2. Only use tools with insulated handles.

3. lay tools or other metal parts on top of battery or any battery terminals. DO NOT

4. Wear rubber gloves and boots.

5. Determine if the battery is inadvertently grounded. If inadvertently grounded, remove source of ground. CONTACT WITH A GROUNDED

BATTERY CAN RESULT IN ELECTRICAL SHOCK! The likelihood of such shock will be reduced if such grounds are r emoved during installation

and maintenance (applicable to a UPS and a remote battery supply not having a grounded circuit).

 BATTERY REPLACEMENT PROCEDURE:

Line mode

Select SW

Press

UPS Status Display Capacity Display Digital Value Display

Load

Cap.

Battery

Cap.

Input

Voltage

Output

Voltage

Run

Time

% of

Load

% of

Batt.

Initial V X -- X V X V

1st V X -- X V X V

2nd V X -- X V X V

3rd V X -- X X V V

4th V X -- X V X V

5th(Return) V X -- X V X V

Press >3sec

(Sound Disable) V X V X -- -- -- -- -- -- --

Press >3sec

Again

(Sound Enable)

V X X X -- -- -- -- -- -- --

(Overload) V X -- V -- -- -- -- -- -- --

"V" : Illuminated, "X" : Not Illuminated, "--" : Either

Battery mode

Select SW

Press

UPS Status Display Capacity Display Digital Value Display

Load

Cap.

Battery

Cap.

Input

Voltage

Output

Voltage

Run

Time

% of

Load

% of

Batt.

Initial X V -- X X V V

1st X V -- X X V V

2nd X V -- X V X V

3rd X V -- X X V V

4th X V -- X X V V

5th(Return) X V -- X X V V

Press >3sec

(Sound Disable) X V V X -- -- -- -- -- -- --

Press >3sec

again(Sound

Enable)

X V X X -- -- -- -- -- -- --

(Overload) X V -- V -- -- -- -- -- -- --

"V" : Illuminated, "X" : Not Illuminated, "--" : Either

BASIC OPERATION

INSTALLING YOUR UPS SYSTEM

IMPORTANT SAFETY WARNINGS

DEFINITIONS FOR ILLUMINATED LCD INDICATORS

1. Remove the right-side of the faceplate.

Remove the three retaining screws on

the cable protection cover then remove

the cover.

3. Disconnect the black and red

cable.

4. Remove the retaining screw of the cable

connectors.

5. Replace the new battery pack. Assemble

the screws, cover, cable and front panel in

the reverse sequence of above steps.

Recharge the unit for 8 hours to ensure

the UPS performs expected runtime.

Problem Possible Cause Solution

Full-time surge protection

outlets stop providing power

to equipment.

Circuit breaker has tripped

due to an overload.

Turn the UPS off and unplug at least one piece of

equipment. Wait 10 seconds, reset the circuit breaker by

depressing the button, and then turn the UPS on.

The UPS does not provide

expected runtime.

Battery not fully charged. Recharge the battery by leaving the UPS plugged in.

Battery is slightly worn out. Contact CyberPower Systems about replacement batteries

at tech@cpsww.com

The UPS will not turn on.

The on/off switch is designed

to prevent damage by rapidly

turning it off and on.

Turn the UPS off. Wait 10 seconds and then turn the UPS

on.

The battery is worn out. Contact CyberPower Systems about replacement batteries

at tech@cpsww.com

Mechanical problem. Contact CyberPower Systems at tech@cpsww.com

PowerPanel® Business

Edition is inactive.

The USB cable is not connected. Connect the USB cable to the UPS unit and an open

USB port on the back of the computer.

The unit is not providing battery

power.

Shutdown your computer and turn the UPS off. Wait 10

seconds and turn the UPS on. This should reset the unit.

Additional troubleshooting information can be found under “Support” at www.CPSww.com

Model OR1000LCDRM1U OR1500LCDRM1U

Capacity 1000VA / 600W 1500VA / 900W

Nominal Input Voltage 90Vac to 140Vac

Input Frequency 60 Hz +/- 3 Hz(Auto-sensing)

On-Battery Output Voltage 120Vac +/- 5%

On-Battery Output Wave Form Simulated Sine Wave

Operating Temperature + 32°F to 104° F / 0° C to 40° C

Size (W x H x D) 1U Rack 17.3 x 1.8 x 15.8 1U Rack 17.3 x 1.8 x 19.5

Weight 35.5lbs 45.6lbs

Battery Type CyberPower / RB0670X4 CyberPower / RB0690X4

Typical Battery Recharge Time 8 hours from total discharge

Typical Battery Life 3 to 6 years, depending on number of discharge/recharge cycles

Recommended Battery Sealed Maintenance Free Lead Acid Battery

Safety Approvals UL1778 4th, cUL CSA C22.2 No.107.3-05, FCC/DoC Class B

SYSTEM FUNCTIONAL BLOCK DIAGRAM

Advanced Energy-Saving Patented Bypass Technology

CyberPower’s patented GreenPower UPS™ with Bypass Technology reduces UPS energy costs by up to

75% compared to conventional UPS models. Even when utility power is normal, conventional UPS models

constantly pass power through a transformer. By contrast, under normal conditions the advanced circuitry

of a GreenPower UPS™ bypasses the transformer. As a result, the power efficiency is significantly

increased while decreasing waste heat, using less energy, and reducing energy costs.

When an abnormal power condition occurs, the GreenPower UPS™ automatically runs power through its

transformer to regulate voltage and provide “safe” power. Since utility power is normal over 88% of the time, the GreenPower UPS™

operates primarily in its efficient bypass mode.

The GreenPower UPS™ is also manufactured in accordance with the Restriction on Hazardous Substances (RoHS) directive making

it one of the most environmentally-friendly on the market today.

Read the following terms and conditions carefully before using the CyberPower OR1000LCDRM1U/OR1500LCDRM1U (the

“Product”). By using the Product you consent to be bound by and become a party to the terms and conditions of this Limited Warranty

and Connected Equipment Guarantee (together referred to as this “Warranty”). If you do not agree to the terms and conditions of this

Warranty, you should return the Product for a full refund prior to using it.

Who is Providing this Warranty?

CyberPower Systems (USA), Inc. (“CyberPower”) provides this Limited Warranty.

What Does This Warranty Cover?

This warranty covers defects in materials and workmanship in the Product under normal use and conditions. It also covers

equipment that was connected to the Product and damaged because of the failure of the Product.

What is the Period of Coverage?

This warranty covers the Product for three years and connected equipment for as long as you own the Product.

Who Is Covered?

This warranty only covers the original purchaser. Coverage ends if you sell or otherwise transfer the Product.

How Do You Get Warranty Service?

1. Before contacting CyberPower, identify Your Product model number, the Purchase Date, and each item of Connected

Equipment (E.G. Computer tower, Computer Monitor, Ink Jet Printer, Cable Modem, etc).

2. Visit our web site at http://www.cpsww.com/support or Call us at (877) 297-6937.

3. If your product requires warranty service you must provide a copy of your dated purchase receipt or invoice.

How Do You Open A Connected Equipment Claim?

1. Call us at (877) 297-6937 or write to us at Cyber Power Systems (USA), Inc., 4241 12th Ave. E., STE 400, Shakopee, MN

55379, or send us an e-mail message at claims@cpsww.com for instructions, within 10 days of the occurrence.

2. When you contact CyberPower, identify the Product, the Purchase Date, and the item(s) of Connected Equipment. Have

information on all applicable insurance or other resources of recovery/payment that are available to the Initial Customer and

Request a Claim Number.

3. You must provide a dated purchase receipt (or other proof of the original purchase) and provide a description of the damage to

your connected equipment.

4. Pack and ship the product to CyberPower and, if requested, the item(s) of Connected Equipment, a repair cost estimate for the

damage to the Connected Equipment, and all claim forms that CyberPower provides to you. Show the Claim Number on the

shipping label or include it with the product. You must prepay all shipping costs, you are responsible for packaging and

shipment, and you must pay the cost of the repair estimate.

How Long Do I Have To Make A Claim?

All claims must be made within ten days of the occurrence.

What Will We Do To Correct Problems?

CyberPower will inspect and examine the Product.

If the Product is defective in material or workmanship, CyberPower will repair or replace it at CyberPower's expense, or, if

CyberPower is unable to or decides not to repair or replace the Product (if defective) within a reasonable time, CyberPower will refund

to you the full purchase price you paid for the Product (purchase receipt showing price paid is required).

If it appears that our Product failed to protect any equipment plugged into it, p2-we will also send you forms for making your claim for the

connected equipment. We will repair or replace the equipment that was damaged because of the failure of our Product or pay you

the fair market value (NOT REPLACEMENT COST) of the equipment at of the time of the damage. We will use Orion Blue Book, or

another a third-party valuation guide, or eBay, craigslist, or other source to establish that amount. Our maximum liability is limited to

$300,000 for the OR1000LCDRM1U and the OR1500LCDRM1U.

Who Pays For Shipping?

We pay when p2-we send items to you; you pay when you send items to us.

What isn’t covered by the warranty?

1. This Warranty does not cover any software that was damaged or needs to be replaced due to the failure of the Product or any

data that is lost as a result of the failure or the restoration of data or records, or the reinstallation of software.

2. This Warranty does not cover or apply to: misuse, modification, operation or storage outside environmental limits of the Product

or the equipment connected to it, nor for damage while in transit or in storage, nor if there has been improper operation or

maintenance, or use with items not designed or intended for use with the Product, such as laser printers, appliances, aquariums,

medical or life support devices, etc.

What are the Limitations?

The sole and exclusive remedies of the Initial Customer are those provided by this Warranty.

1. This Warranty does not apply unless the Product and the equipment that was connected to it were connected to properly wired

and grounded outlets (including compliance with electrical and safety codes of the most current electrical code), without the use

of any adapters or other connectors.

2. The Product must have been plugged directly into the power source and the equipment connected to the Product must be

directly connected to the Product and not “daisy-chained” together in serial fashion with any extension cords, another Product

or device similar to the Product, surge suppressor, or power tap. Any such installation voids the Limited Warranty.

3. The Product and equipment connected to it must have been used properly in a suitable and proper environment and in

conformance with any license, instruction manual, or warnings provided with the Product and the equipment connected to it.

4. The Product must have been used at all times within the limitations on the Product’s VA capacity.

The Product was designed to eliminate disrupting and damaging effects of momentary (less than 1ms) voltage spikes or impulses

from lightning or other power transients. If it can be shown that a voltage spike lasting longer than 1ms has occurred, the occurrence

will be deemed outside the rated capabilities of the Product and the Limited Warranty is void. CyberPower Does Not Cover or

Undertake Any Liability in Any Event for Any of the Following:

1. Loss of or damage to data, records, or software or the restoration of data or records, or the reinstallation of software.

2. Damage from causes other than AC Power Line Transients, spikes, or surges on properly installed, grounded and

code-compliant 120 volt power lines in the United States and Canada; transients, surges or spikes on standard telephone land

lines, PBX telephone equipment lines or Base 10T Ethernet lines, when properly installed and connected. (This exclusion

applies, for example, to fluctuations in data transmission or reception, by CATV or RF transmission or fluctuations, or by

transients in such transmission.)

3. Damage from any circumstance described as excluded above with respect to the Product.

4. Damages from fire, flood, wind, rain, rising water, leakage or breakage of plumbing, abuse, misuse or alteration of either the

product or the Connected Equipment.

5. CyberPower excludes any liability for personal injury under the Limited Warranty and Connected Equipment Guarantee.

CyberPower excludes any liability for direct, indirect, special, incidental or consequential damages, whether for damage to or

loss of property [EXCEPT FOR (AND ONLY FOR) the specific limited agreement of CyberPower to provide certain warranty

benefits regarding "Connected Equipment" under this Warranty], loss of profits, business interruption, or loss of information or

data. NOTE: Some States or Provinces do not allow the exclusion or limitation of incidental or consequential damages, so the

above limitation may not apply to you.

6. The Product is not for use in high-risk activities or with aquariums. The Product is not designed or intended for use in hazardous

environments requiring fail-safe performance, or for use in any circumstance in which the failure of the Product could lead

directly to death, personal injury, or severe physical or property damage, or that would affect operation or safety of any medical

or life support device (collectively, "High Risk Activities"). CyberPower expressly disclaims any express or implied warranty of

fitness for High Risk Activities or with aquariums. CyberPower does not authorize use of any Product in any High Risk Activities

or with Aquariums. . ANY SUCH USE IS IMPROPER AND IS A MISUSE OF THE PRODUCT

Where Can I Get More Information?

The application of the United Nations Convention of Contracts for the International Sale of Goods is expressly excluded.

CyberPower is the warrantor under this Limited Warranty.

For further information please feel free to contact CyberPower at CyberPower Systems (USA), Inc. 4241 12th Ave E., STE 400,

Shakopee, MN 55379; call us at (877) 297-6937; or send us an e-mail message at claims@cpsww.com.

CyberPower Systems encourages environmentally sound methods for disposal and recycling of its UPS products.

Please dispose and/or recycle your UPS and batteries in accordance to the local regulations of your state.

TECHNICAL SPECIFICATIONS

Limited Warranty and Connected Equipment Guarantee

CYBERPOWER GREENPOWER UPS TECHNOLOGY™

EMI

Filter

Surge

Suppressor

AVR

Charger

AC/DC

Battery

Inverter

Input Output

Normal Mode

Battery Mode

TROUBLESHOOTING

Product specificaties

Merk:	CyberPower
Categorie:	UPS
Model:	OR1000LCDRM1U
Kleur van het product:	Zwart
Gewicht:	16102 g
Breedte:	438 mm
Diepte:	400.5 mm
Hoogte:	44.4 mm
Vormfactor:	Rackmontage
Aantal USB 2.0-poorten:	1
Aantal Ethernet LAN (RJ-45)-poorten:	1
Ondersteund aantal accu's/batterijen:	4
Certificering:	UL1778, cUL 107.1, FCC DOC B
Geluidsalarm(en):	Ja
Responstijd:	4 ms
Duurzaamheidscertificaten:	ENERGY STAR
Uitgangsvermogen:	600 W
Accu/Batterij oplaadtijd:	8 uur
Frequentie:	60 Hz
Seriële poort(en):	1
Modem (RJ-11) poort:	1
Stekker:	C14 stekker
Rackcapaciteit:	1U
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 95 procent
Type beeldscherm:	LCD
Surge energy rating:	1030 J
Aantal AC uitgangen:	- AC-uitgang(en)
Stopcontacttypes:	NEMA 5–15R
Output power capacity:	1 kVA
Ingang operation voltage (min):	90 V
Ingang operation voltage (max):	140 V
Uitgang operation voltage (min):	- V
Uitgang operation voltage (max):	120 V
UPS-topologie:	Line-interactive
Typische backup tijd op halve lading:	13 min
Typische backup tijd op volledige lading:	3 min
Spanningsbeveiliging:	Ja
Automatic Voltage Regulation (AVR):	Ja
Vervangings-batterij cartridge:	BB - BP7-6