CyberPower CyberShield CS24C12V2-E Handleiding

CyberPower UPS CyberShield CS24C12V2-E

Lees hieronder de 📖 handleiding in het Nederlandse voor CyberPower CyberShield CS24C12V2-E (2 pagina's) in de categorie UPS. Deze handleiding was nuttig voor 21 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

User’s Manual for

CyberShield

CS24C12V2-E

CyberShield Battery Backup Power Supplies are designed to provide a

local power solution for cable telephony, wireless local loop (WLL), and

ﬁber to the home (FTTH) broadband equipment.

IMPORTANT SAFETY WARNINGS

(SAVE THESE INSTRUCTIONS)

This manual contains important instructions regarding the installation and operation of this device.

Read this manual thoroughly before attempting to unpack , install or operate this device

CAUTION! The battery can energize hazardous live parts inside even when the AC input power is

disconnected.

CAUTION! To reduce the risk of electric shock, do not remove the cover, except to service the

battery. No user serviceable parts inside, except for the battery.

CAUTION! To avoid electric shock, turn off the unit and unplug it from the AC power source before

servicing the battery or installing a computer component.

ENCLOSURE INSTALLATION

Carefully follow these instructions during installation of this device:

1.) Carry out the installation in a safe area that is free of excessive dust and has adequate airﬂow.

2.) Screws must be appropriate for total weight of the Battery Backup Power Supply and the

mounting surface material .

3.) Do not operate the Battery Backup Power Supply where the temperature and humidity are

outside the speciﬁed limits. (Refer to speciﬁcations in this manual.)

BATTERY REPLACEMENT

This battery is hot-swappable. As long as utility power is on , you may leave the Battery Backup

Power Supply and connected equipment on while replacing a new battery.

Once the battery is disconnected, the connected equipment is not protected from power

outages.

Deliver spent batteries to a recycling facility or ship to the manufacturer in the

replacement battery packing material.

WARNING INDICATOR

OPERATION

Connect: Equipment and Power

Step1. Plug the Battery Backup Power Supply power cord into the utility power cord inlet

Step2. Plug the Battery Backup Power Supply power cord into the wall outlet.

The Battery Backup Power Supply battery charges when it is connected to utility power.

The battery charges fully during the ﬁrst of normal operation. Do not expect 24 hours

full battery run capability during this initial charge period.

COLD START

The cold start feature is for applying power to the Battery Backup Power Supply and connected

equipment when the Battery Backup Power Supply is oﬀ and there is no utility power. Before using

the cold start feature, please make sure the battery is charged. To enable the cold start feature,

press the recessed cold start button with a small pointed object.

Battery Backup Power Supply is on utility power.

Battery Backup Power Supply is on battery power.

DC output power is provided by the battery or

utility power.

The battery is not connected or the battery needs to be

replaced.

Green

Yellow

Green

Red

Indicator Color Condition

Step 1:

a. Remove the case screw.

b. Open the battery cover.

Step 2:

a. Unstrap strap from battery.

b. Slide battery oﬀ of the

shelf.

c. Disconnect battery cable

connector at the chassis end.

Step 3:

a. Use the enclosed installation template to

mark an installation location for the unit.

b. Mount the unit on the wall with 3 mounting

screws into the keyhole slots.

c. Tighten the screws to secure the units.

d. Connect the battery connector and replace

the battery back.

Step 1:

a. Remove the case screw.

b. Open the battery cover.

Step 2:

a. Loosen the battery strap.

b. Disconnect battery cable connector

to remove battery.

c. Replace with new battery and

re-connect the battery connector.

Step 3:

a. Tighten the battery strip

b. Close the battery cover and

lock the case screw.

Front Panel

CS24C12V2-E

INTELLIGENT BACK-UP PO WER

OUTPUT

BATTERY

Installation Suggestion:

To prevent the unit from intrusion of foreign matter, we suggest that the unit should be mounted on

a piece of wood which should then be attached to a wall underneath eaves.

Power Cable Selection:

A power cable (4.5m max.) being identiﬁed as 18AWG, "OUTDOOR" or "WATERPROOF"

should be selected while necessary.

COMMUNICATION SIGNALS

The communication signals of this unit are isolated from the internal circuitry via open collector opto-

coupled transistors. The connection “SIG RTN” (Signal Return) is a common return point for all

communication signals. In the typical application, the attached equipment digital ground connects to

Signal Return, and pull-up resistors turn the open collector signals into logic levels.

SPECIFICATION

LIMITED WARRANTY

CyberPower warrants to you, the Initial Purchaser, that the Product will be free from defects in material and workmanship for three years from the date of original purchase, subject to the terms of this Limited

Warranty. This Limited Warranty gives you speciﬁc rights, and you may have other rights, which vary from State to State or Province to Province.

Any Implied Warranty of Merchantability or for Fitness for a Particular Purpose, if applicable to the Product, is limited in duration to three years. This provision shall NOT create any Implied Warranty or

Merchantability or of Fitness for a Particular Purpose that would not otherwise apply to the Product. NOTE: Some States and Provinces do not allow limitations on how long an implied warranty lasts,

so the above limitation may not apply to you.

To be covered you must still be the owner of the Product at the time of the failure that results in the claim made under this Limited Warranty. Your sole and exclusive remedies are those provided by this

Limited Warranty. This exclusion of other express warranties applies to written and oral express warranties. CyberPower excludes any liability for personal injury. CyberPower excludes any liability for direct,

indirect, special, incidental, or consequential damages, whether for damage to or loss of property, loss of proﬁts, business interruption, information or data. This exclusion applies even though damage or loss

is caused by negligence or other fault. NOTE: Some States or Provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you.

DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT OR OTHER HIGH RISK ACTIVITIES.

CyberPower does not sell the PRODUCT for use in high-risk activities. The PRODUCT is not designed or intended for use in hazardous environments requiring fail-safe performance, including the operation

of nuclear facilities, aircraft navigation or communication systems, air traﬃc control, weapons systems, life support or medical applications or for use in any circumstance in which the failure of the PRODUCT

could lead directly to death, personal injury, or severe physical or property damage, or that would aﬀect operation or safety of any medical or life support device (collectively, "High Risk Activities").

CyberPower expressly disclaims any express or implied warranty of ﬁtness for High Risk Activities. CyberPower does not authorize use of any PRODUCT in any High Risk activities.

ANY SUCH USE IS IMPROPER AND IS A MISUSE OF A CYBERPOWER PRODUCT.

The Limited Warranty is governed by the laws of the United States and the State of Minnesota, without reference to conﬂict of law principles. The application of the United Nations Convention of Contracts for

the International Sale of Goods is expressly excluded

FCC NOTICE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with these instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment oﬀ and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1)Reorient or relocate the receiving antenna.

(2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit diﬀerent from that to which the receiver is connected. (4) Consult the dealer or an

experienced radio/TV technician for help.

CAUTION: Shielded signal cables must be used with this device to ensure compliance with Class B FCC limits.

CAUTION: Any changes or modiﬁcations not expressly approved by Cyber Power could void the authority granted by the FCC to operate this equipment.

For more information, please contact:

CyberPower Systems ( USA ), Inc. 4241 12th Avenue East, Suite 400, Shakopee, MN55379 Phone: (952)403-9500 Fax: (952)403-0009 www.cpsww.com

CyberPower Systems ( EUROPE ), Inc. Flight Forum 3545, 5657DW Eindhoven, The Netherlands E-mail: sales@cyberpower-eu.com eu.cyberpowersystems.com

Input

Voltage Range

Frequency Range

Output

On Battery Output Voltage

Continuous Power Capability

Output Power Max

Efficiency (at 75% Max Load)

Battery

Battery Type

Numbers of Battery

Typical Recharge Time

Replaceable

Surge Protection and Filtering

Lightning / Surge Protection

Warning Diagnostics

Indicators

Management

Auto-Charge

Communication Interface

Physical

Maximum Dimensions (L*W*D)

Weight (kg)

Environment

Operating Temperature

Operating Humidity

Max Operating Elevation

Max Storage Elevation

Storage Temperature

100Vac - 240Vac (Universal Input)

50 - 60 Hz

12Vdc

24W

> 75 %

Sealed, Maintenance Free Lead-Acid Battery

7.2AH / 12V x 1

18Hours

Yes

AC, Output, Battery

Yes

On Battery, Replace Battery, Battery Missing,

Low Battery

27.5cm x 20.4cm x 9.9cm

3.51

5oF - 122oF (-15oC - 50oC)

0 - 95% noncondensing within enclosure

10,000ft (3,000m)

50,000ft (15,000m)

5oF - 122oF (-15oC - 50oC)

12V

12V RTN

SIG RTN

ON BATTERY

REPLACE

BATTERY

MISSING

LOW BATTERY

+ Voltage output

- Voltage output

Signal return

Low when operating from utility line.

Open when operating from battery.

Low when battery is charged.

Open when battery fails the Self Test.

Low when battery is present.

Open when battery is missing.

Low when battery is near full charge capacity.

Open when operating from a battery with < 20%

capacity.

CS24C12V2-E Message

K01-2412H10-03

Model CS24C12V2-E

Back Panel

CS24C12V2-E

12V 24W

RISK OF ELECTRICAL SHOCK. DO NOT REMOVE COVER.

NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL. FOR USE IN A CONTROLLED ENVIRONMENT.

REFER TO MANUAL FOR ENVIRONMENTAL CONDITIONS.

E235457

FCC CLASS B VERIFIED

Cont ains sealed nonspillab le lead acid b attery .

Mus t be properly recy cled or dispos ed.

INPUT:

CAUTION:

/ CS24C12V2-E

100-240V~ 50-60Hz ; 0.75A OUTPUT:

Made In China

68FG

LISTED

Product specificaties

Merk:	CyberPower
Categorie:	UPS
Model:	CyberShield CS24C12V2-E
Kleur van het product:	Wit
Gewicht:	3492.66 g
Breedte:	273.05 mm
Diepte:	95.25 mm
Hoogte:	203.2 mm
Snoerlengte:	3 m
Gewicht verpakking:	4535.9 g
LED-indicatoren:	Batterijvervanging
Afmetingen verpakking (BxDxH):	355.6 x 120.65 x 355.6 mm
Duurzaamheidscertificaten:	RoHS
Uitgangsvermogen:	24 W
Accu/Batterij oplaadtijd:	18 uur
Temperatuur bij opslag:	-15 - 45 °C
Frequentie:	50/60 Hz
Hoogte, in bedrijf:	0 - 3000 m
Hoogte bij opslag:	0 - 15000 m
Efficientie:	76 procent
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 95 procent
Batterijtechnologie:	Sealed Lead Acid (VRLA)
Aantal AC uitgangen:	- AC-uitgang(en)
Nominale input voltage:	- V
Output power capacity:	- kVA
Hot-swap batterij:	Ja
Netspanning, in bedrijf:	87-264 V
Hoorbare alarmstanden:	Batterijvervanging
Koude start:	Ja