CyberPower CP685AVRLCD Handleiding

CyberPower UPS CP685AVRLCD

Lees hieronder de 📖 handleiding in het Nederlandse voor CyberPower CP685AVRLCD (2 pagina's) in de categorie UPS. Deze handleiding was nuttig voor 40 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

1. Power Switch: Used as the master on/o switch for equipment connected to the battery power

supplied outlets. To turn the UPS ON, press the power button for approximately 2 seconds - you will

hear a constant tone (1 second) - and release after a short beep.

Alarm setting (For CP825AVRLCD-G/CP685AVRLCD-G): The audible alarm can be turned O or On

by double click the POWER button. The default setting is for the Alarm On. To turn the Alarm O,

double click the button. You will hear two short beeps when the Alarm is turned o. To turn the Alarm

back On, double click the button. You will hear a single short beep when the Alarm is turned on. *When

the Alarm is turned O, there will be no audible notiﬁcation when the UPS reaches a low battery state.

2. Power On Indicator: This LED is illuminated when the utility power is normal and the UPS outlets are

providing power, free of surges and spikes.

3. Mode Switch (For CP825AVRLCD-G/CP685AVRLCD-G): Press the Mode Switch for approximately 3

seconds to enter setup mode to view options: Utility High/low Voltage range, sensitivity setup, LCD

sleep ON/OFF, battery test, buzzer ON/OFF, and low battery alarm. When an option is selected, wait

for 8 seconds for the setting to be conﬁrmed. After the setting has been conﬁrmed the LCD screen will

leave setup mode and go back to status display. If there is no action for 8 seconds during setup, the

LCD will also leave setup mode and go back to the status display.

4. Fault Indicator: This LED is illuminated if there is a problem with the UPS.

5. Mute Button (For CP800AVR/CP685AVR-G): Press the button for 2 seconds to enable the audible

alarm (beeps once) or disable (beeps twice) the audible alarm.

6. LCD module display (For CP825AVRLCD-G/CP685AVRLCD-G): LCD display shows all the UPS

information using icons and messages. For more information please review the “Deﬁnitions for

Illuminated LCD Indicators” section.

7. Battery and Surge Protected Outlets: The unit has four battery powered and surge protected outlets

to ensure temporary uninterrupted operation of your equipment during a power failure. (DO NOT plug

a laser printer, paper shredder, copier, space heater, vacuum cleaner, sump pump, or other large

electrical device into the “Battery and Surge Protected Outlets.” The power demands of

these devices will overload and possibly damage the unit.)

8. Full-Time Surge Protection Outlets: The unit has four surge suppression outlets.

To turn the UPS OFF, press the power button for approximately 2 seconds - you will hear a constant

tone (1 second) - and release after two short beeps.

9. USB Port: The USB port allows connection and communication between the USB port on the

computer and the UPS unit.

10. Communication Protection Ports (For CP825AVRLCD-G): Communication protection ports, bi-

directional, will protect a 10/100/1000 Ethernet connection(RJ45).

11. Serial Port: Serial Port allow for bi-directional communication among the UPS and the computer.

The UPS can control the computer’s shutdown in case of an emergency, and at the same time, the

computer can monitor the UPS and alter its various programmable parameters.

12. Circuit Breaker & reset: Located on the side of the UPS, the circuit breaker provides overload and

fault protection.

13. Ground Screw: The ground screw is used for any equipment that needs a chassis ground connection.

14. Outlets Designed for AC Adapters: The UPS unit has four widely-spaced outlets. AC power adapters

can be plugged into the UPS without overlapping or blocking adjacent outlets.

REPLACING THE BATTERY

Replacement of batteries located in an OPERATOR ACCESS AREA.

1. When replacing batteries, replace with the same number of the following battery: CyberPower /

RB1290 for CP825AVRLCD-G,CP800AVR; CyberPower / RB1270B for CP685AVRLCD-G,CP685AVR-G.

2. CAUTION! Risk of Energy Hazard, 12V, maximum 9 Ampere-hour battery. Before replacing batteries,

remove conductive jewelry such as chains, wrist watches, and rings. High energy through conductive

materials could cause severe burns.

3. CAUTION! Do not dispose of batteries in a ﬁre. The batteries may explode.

4. CAUTION! Do not open or mutilate batteries. Released material is harmful to the skin and eyes.

It may be toxic.

5. CAUTION: A battery can present a risk of electrical shock and high short circuit current. The following

precautions should be observed when working on batteries:

a. Remove watches rings, or other metal objects.

b. Use tools with insulated handles.

CAUTION: risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries

according to local regulations.

TO REPLACE THE BATTERY

1. Turn o and unplug all connected equipment.

2. Unplug it from the AC power source.

3. Turn the UPS upside down.

4. Remove the 1 retaining screw.

5. Slide the battery compartment cover completely o of the unit.

6. Remove the battery from the compartment.

7. Disconnect the battery cables from the battery.

8. Install the replacement battery by connecting the red wire and

black wire to the positive (+) and negative (-) terminal of the battery.

9. Put the battery back into the compartment.

10. Slide back the battery compartment cover and tighten the retaining screw.

11. Charge the unit for 8 hours to fully charge the battery.

REMINDER: Batteries are considered HAZARDOUS WASTE and must be disposed of properly. Most

retailers that sell lead-acid batteries collects used batteries for recycling, as required by local regulations.

CP825AVRLCD-G | CP685AVRLCD-G | CP800AVR | CP685AVR-G

User’s Manual

PRODUCT REGISTRATION

IMPORTANT SAFETY INSTRUCTIONS

INSTALLING YOUR UPS SYSTEM

BASIC OPERATION

BASIC OPERATION CONT.

DEFINITIONS FOR LED INDICATORS & AUDIBLE ALARMS

Thank you for selecting this CyberPower UPS product. This UPS is designed to provide

unsurpassed power protection, operation and performance during the lifetime of the product.

Please take a few minutes to register your product by visiting: CyberPowerSystems.com/

registration. Registration certiﬁes your product’s warranty, conﬁrms your ownership in the event

of a product loss or theft and entitles you to free technical support.

(SAVE THESE INSTRUCTIONS)

This manual contains important safety instructions. Please read and follow all instructions carefully during

installation and operation of the unit. Read this manual thoroughly before attempting to unpack, install, or

operate your UPS.

CAUTION! To prevent the risk of ﬁre or electric shock, install in a temperature and humidity controlled

indoor area free of conductive contaminants. (Please see speciﬁcations for acceptable temperature and

humidity range).

CAUTION! To reduce the risk of electric shock, do not remove the cover except to service the battery.

Turn o and unplug the unit before servicing the batteries. There are no user serviceable parts inside

except for the battery.

CAUTION! Hazardous live parts inside can be energized by the battery even when the AC input power

is disconnected.

CAUTION! The UPS must be connected to an AC power outlet with fuse or circuit breaker protection.

Do not plug into an outlet that is not grounded. If you need to de-energize this equipment, turn o and

unplug the unit.

CAUTION! To avoid electric shock, turn o the unit and unplug it from the AC power source before

installing a computer component.

CAUTION! Not for use in a computer room as deﬁned in the Standard for the Protection of Electronic

Computer/Data Processing Equipment, ANSI/NFPA 75.

CAUTION! To reduce the risk of ﬁre, connect only to a circuit provided with 20 amperes maximum branch

circuit over current protection in accordance with the National Electric Code, ANSI/NFPA 70.

DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT! CyberPower Systems does not sell

products for life support or medical applications. DO NOT use in any circumstance that would aect

operation and safety of life support equipment, any medical applications or patient care.

DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of ﬁre or electric shock, do not use with or

near an aquarium. Condensation from the aquarium can cause the unit to short out.

DO NOT USE THE UPS ON ANY TRANSPORTATION! To reduce the risk of ﬁre or electric shock, do not

use the unit on any transportation such as airplanes or ships. The eect of shock or vibration caused

during transit and the damp environment can cause the unit to short out.

INTRODUCTION

Thank you for selecting a CyberPower Systems UPS product. This UPS is designed to provide

unsurpassed power protection, operation and performance during the lifetime of the product.

UNPACKING

Inspect the UPS upon receipt. The box should contain the following: (a) UPS unit (b) User’s manual

visit CyberPowerSystems.com and go to the Software Section for free download.

OVERVIEW

The CP825AVRLCD-G/CP685AVRLCD-G/CP800AVR/CP685AVR-G provides complete power protection

from utility power that is not always consistent. The CP825AVRLCD-G/CP685AVRLCD-G/CP800AVR/

CP685AVR-G features 1030 Joules of surge protection. The unit provides long lasting battery backup

during power outages with maintenance free batteries.The CP825AVRLCD-G/CP685AVRLCD-G/

CP800AVR/CP685AVR-G ensures consistent power to your computer system and includes software that

will automatically save your open ﬁles and shutdown your computer system during a utility power loss.

AUTOMATIC VOLTAGE REGULATOR

The CP825AVRLCD-G/CP685AVRLCD-G/CP800AVR/CP685AVR-G stabilizes inconsistent utility power

to nominal levels that are safe for equipment. Unstable utility power can be damaging to important data

and hardware. With Automatic Voltage Regulation (AVR), damaging voltage levels are corrected to safe

levels. AVR automatically increases low utility power to a consistent and safe 110/120 volts.

HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT

1. Ensure that the equipment plugged into the UPS does not exceed the UPS unit’s rated capacity

(825VA/450W for CP825AVRLCD-G, 800VA/450W for CP800AVR, 685VA/390W for

CP685AVRLCD-G, CP685AVR-G). If the rated capacities of the unit are exceeded, an overload

condition may occur and cause the UPS unit to shut down or the circuit breaker to trip.

2. There are many factors that can aect the amount of power that your electronic equipment will

require. For optimal system performance keep the load below 80% of the unit’s rated capacity.

HARDWARE INSTALLATION GUIDE

1. Your new UPS may be used immediately upon receipt.

However, after receiving a new UPS, to ensure the battery’s

maximum charge capacity, it is recommended that you charge

the battery for at least 8 hours. Your UPS is equipped with

an auto-charge feature. When the UPS is plugged into an AC

outlet, the battery will automatically charge whether the UPS

is turned on or turned o. Note: This UPS is designed with a

safety feature to keep the system from being turned on during

shipment. The ﬁrst time you turn the UPS on, you will need to

have it connected to AC power or it will not power up.

2. With the UPS unit turned o and unplugged, connect your

computer, monitor, and any other peripherals requiring battery backup into the battery power supplied

outlets. Plug the other peripheral equipment (eg. printer, scanner, speakers, etc.) into the full-time

surge protection outlets. DO NOT plug a laser printer, paper shredder, copier, space heater, vacuum

cleaner, sump pump, or other large electrical device into the “Battery and Surge Protected Outlets”.

The power demands of these devices will overload and possibly damage the unit.

3. Plug the UPS into a 2 pole, 3 wire grounded receptacle (wall outlet). Make sure the wall branch outlet

is protected by a fuse or circuit breaker and does not service equipment with large

electrical demands (e.g. air conditioner, refrigerator, copier, etc.). The warranty

prohibits the use of extension cords, outlet strips, and surge strips in conjunction

with the UPS unit.

4. Press the power switch to turn the unit on. The Power On indicator light will

illuminate green and the unit will “beep” once.

5. If an overload is detected, an audible alarm will sound and the unit will emit one long beep. To correct

this, turn the UPS o and unplug at least one piece of equipment from the battery power supplied

outlets. Make sure the circuit breaker is depressed and then turn the UPS on.

6. To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times.

7. To store the UPS for an extended period of time, cover it and store with the battery fully charged.

While in storage, recharge the battery every three months to ensure optimal battery life.

8. Ensure the wall outlet and UPS are located near the equipment being attached for proper accessibility.

INTRODUCTION

CP825AVRLCD-G | CP685AVRLCD-G CP800AVR | CP685AVR-G

POWER FAULT ALARM

CONDITION

On O O Normal

On O

Beep twice

every 30

seconds

Utility Failure: The UPS is providing power to battery pow-

er-supplied outlets from its battery.

On O

Rapid

beeping every

½ second

Utility Failure: The UPS is providing battery power. Rapid

beeping indicates the unit will run out of power soon.

On/O

Flash once

every 5

seconds

Constant tone

Battery Mode or AC/Utility Power Mode Overload Fault:

Occurs when connected equipment exceeds the rating of

battery outlets of the unit. Please unplug at least one piece

of equipment from battery outlets.

O

Flash twice

every 5

seconds

Constant tone

Battery Output Short Fault: Please unplug at least one

piece of equipment from battery outlets and turn on the

UPS again. If the fault still exists, please contact Cyber-

Power Systems for support.

Flash 3

times every

5 seconds

Constant tone Charger Fault: Contact CyberPower Systems for support.

DEFINITIONS FOR ILLUMINATED LCD INDICATORS (CP825/685AVRLCD-G)

INPUT voltage meter: This meter measures the AC voltage that the UPS system is receiving from the

utility wall outlet. The UPS is designed to continuously supply connected equipment with stable output

voltage. In the event of a complete power loss, severe brownout, or over-voltage, the UPS relies on its

internal battery to supply consistent 110/120 output voltage. The INPUT voltage meter can be used as a

diagnostic tool to identify poor-quality input power.

OUTPUT voltage meter: This meter measure, in real time, the AC voltage that the UPS system is providing

to the computer during normal AC/Utility Power mode, and battery backup mode.

ESTIMATED RUNTIME: This displays the run time estimate of the UPS

with the current battery capacity and load.

NORMAL icon: This icon appears when the UPS is working under

normal conditions.

BATTERY icon: During a severe brownout or blackout, this icon appears and

an alarm sounds (two short beeps followed by a pause) to indicate the UPS is

operating from its internal batteries. During a prolonged brownout orblackout,

the alarm will sound continuously to indicate the UPS’s batteries are nearly out

of power. You should save ﬁles and turn o your equipment immediately or

allow the software to shut the system down.

OVER LOAD icon: This icon appears and an alarm sounds to indicate the

battery-supplied outlets are overloaded. To clear the overload, unplug some of your equipment from the

battery-supplied outlets until the icon turns o and the alarm stops.

BATTERY CAPACITY meter: This meter displays the approximate charge level of the UPS’s internal

battery in 20% increments. During a blackout or severe brownout, the UPS switches to battery power

(the BATTERY icon appears) and the battery charge level decreases.

LOAD CAPACITY meter: This meter displays the approximate output load level of the UPS battery outlets

in 20% increments.

SENSITIVITY meter: This meter displays the sensitivity level of the UPS. It is to control the sensitivity of

the UPS to switch to Battery Mode by selecting UPS shutdown voltage range. When the sensitivity is

increased, the UPS will switch to Battery Mode with less input power variation.

FAULT: The following number appears if there is a problem with the UPS. Press the POWER button to turn

the UPS o.

RUN_TIMEOUTPUTINPUT

Min

LOAD BATT. CAP.

100

The LCD display indicates a

variety of UPS operational

conditions. All descriptions

apply when the UPS is

plugged into an AC outlet

and turned on or when the

UPS is on battery.

*In line mode, the AC input voltage may not stable all the time. To prevent the connected equipment

from damage caused by the unexpected voltage ﬂuctuations, please adjust the sensitivity of the unit

by visiting: www.cyberpowersystems.com and download the LCD setup guide. (CP825AVRLCD-G/

CP685AVRLCD-G); For CP800AVR/CP685AVR-G, please refer the steps as follows*

1. Please make sure that the UPS is in .

2. To Enter the Sensitivity Setup mode, press the MUTE Button for 6 seconds until all indicators ﬂash

rapidly.

3. The unit will show the current SENSITIVITY setting, as shown in the following table.

4. To select LOW Sensitivity setting, shortly press power button until one red indicator ﬂashes.

5. To select Medium Sensitivity setting, press the power button until green indicators ﬂashes.

6. To select High Sensitivity setting, press the power button until green and red indicators ﬂash.

7. To set up a level of sensitivity , hold down the Mute button until the ﬁrst one indicator illuminates.

8. In setup mode, if there is no action within 7 seconds, the unit will exit setup mode, and no setting is done.

Indicators

Illuminate Sensitivity Description

1 (Red) LOW

If the connected equipment can tolerate more power events

(example: unstable power often associated with stormy weather),

select Low Sensitivity and the UPS will go to Battery Mode less

often.

2 (Green) Medium (Default) The UPS will go to Battery Mode if the power is unstable.

3 (Green, Red) High

If the connected equipment is more sensitive to power events,

select High Sensitivity and the UPS will go to Battery Mode more

often.

Additional troubleshooting information can be found at: CyberPowerSystems.com/support

Runtimes based on testing fully-charged, new batteries at normal operating conditions. Runtime curve is

approximate and varies based on battery age, level of charge at test, environment, and other variables.

Read the following terms and conditions carefully before using the CyberPower CP825AVRLCD-G/

CP685AVRLCD-G/CP800AVR/CP685AVR-G (the “CPS Product”). By using the CPS Product you consent to be

bound by and become a party to the terms and conditions of this Limited Warranty and Connected Equipment

Guarantee (together referred to as this “Warranty”). If you do not agree to the terms and conditions of this

Warranty, you should return the CPS Product for a full refund prior to using it.

Who is providing this warranty?

Cyber Power Systems (USA), Inc. (“CyberPower”) provides this Limited Warranty.

What does this warranty cover?

This warranty covers defects in materials and workmanship in the CPS Product under normal use and

conditions. It also covers equipment that was connected to the CPS Product and damaged because of

the failure of the CPS Product.

What is the period of coverage?

This warranty covers the CPS Product for three years from date of purchase and connected equipment for as long as

you own the CPS Product.

Who is covered?

This warranty only covers the original purchaser. Coverage ends if you sell or otherwise transfer the CPS Product.

How do you get warranty service?

1. Before contacting CyberPower, identify Your CPS Product model number, the purchase date, and each item of

Connected Equipment (e.g. computer tower, monitor, ink jet printer, cable modem, etc).

2. Visit our web site at: CyberPowerSystems.com/support or Call us at (877) 297-6937.

3. If your product requires warranty service you must provide a copy of your dated purchase receipt or invoice.

How do you open a connected equipment claim?

1. Call us at (877) 297-6937 or write to us at Cyber Power Systems (USA), Inc., 4241 12th Ave. E.,

STE 400, Shakopee, MN 55379, or e-mail at: claims@cpsww.com for instructions, within 10 days

of the occurrence.

2. When you contact CyberPower, identify the CPS Product, the purchase date, and the item(s) of Connected

Equipment. Have information on all applicable insurance or other resources of recovery/payment that are

available to the Initial Customer and Request a Claim Number.

3. You must provide a dated purchase receipt (or other proof of the original purchase) for the CyberPower unit

and connected equipment. You also need to provide a description of the damage to your

connected equipment.

4. Pack and ship the CPS product to CyberPower and, if requested, the item(s) of Connected Equipment, a

repair cost estimate for the damage to the Connected Equipment, and all claim forms that CyberPower

provides to you. Show the Claim Number on the shipping label or include it with the CPS product. You must

prepay all shipping costs, you are responsible for packaging and shipment, and you must pay the cost of the

repair estimate.

How long do I have to make a claim?

All claims must be made within ten days of the occurrence.

What will we do to correct problems?

CyberPower will inspect and examine the CPS Product. If the CPS Product is defective in material or

workmanship, CyberPower will repair or replace it at CyberPower’s expense, or, if CyberPower is unable to or

decides not to repair or replace the CPS Product (if defective) within a reasonable time, CyberPower will refund

to you the full purchase price you paid for the CPS Product (purchase receipt showing price paid is required). If

it appears that our CPS Product failed to protect any equipment plugged into it, we will also send you forms for

making your claim for the connected equipment. We will repair or replace the equipment that was damaged

because of the failure of our CPS Product or pay you the fair market value (NOT REPLACEMENT COST) of the

equipment at of the time of the damage. We will use Orion Blue Book, or another a third-party valuation guide,

or eBay, craigslist, or other source to establish that amount. Our maximum liability is limited to $200,000 for the

CP825AVRLCD-G/CP800AVR and $125,000 for the CP685AVRLCD-G/CP685AVR-G.

Who pays for shipping?

We pay when we send items to you; you pay when you send items to us.

What isn’t covered by the warranty?

1. This Warranty does not cover any software that was damaged or needs to be replaced due to the failure of

the CPS Product or any data that is lost as a result of the failure or the restoration of data or records, or the

reinstallation of software.

2. This Warranty does not cover or apply to: misuse, modiﬁcation, operation or storage outside environmental

limits of the CPS Product or the equipment connected to it, nor for damage while in transit or in storage, nor

if there has been improper operation or maintenance, or use with items not designed or intended for use

with the CPS Product, such as laser printers, appliances, aquariums, medical or life support devices, etc.

What are the limitations?

The sole and exclusive remedies of the Initial Customer are those provided by this Warranty.

1. This Warranty does not apply unless the CPS Product and the equipment that was connected to it were

connected to properly wired and grounded outlets (including compliance with electrical and safety codes

of the most current electrical code), without the use of any adapters or other connectors.

2. The CPS Product must have been plugged directly into the power source and the equipment connected to

the CPS Product must be directly connected to the CPS Product and not “daisy-chained” together in serial

fashion with any extension cords, another Product or device similar to the CPS Product, surge suppressor, or

power tap. Any such installation voids the Limited Warranty.

3. The CPS Product and equipment connected to it must have been used properly in a suitable and proper

environment and in conformance with any license, instruction manual, or warnings provided with the CPS

Product and the equipment connected to it.

4. The CPS Product must have been used at all times within the limitations on the CPS Product’s VA capacity.

The CPS Product was designed to eliminate disrupting and damaging eects of momentary (less than 1ms)

voltage spikes or impulses from lightning or other power transients. If it can be shown that a voltage spike

lasting longer than 1ms has occurred, the occurrence will be deemed outside the rated capabilities of the

CPS Product and the Limited Warranty is void. CyberPower Does Not Cover or Undertake Any Liability

In any event for any of the following:

1. Loss of or damage to data, records, or software or the restoration of data or records, or the reinstallation of

software.

2. Damage from causes other than AC Power Line Transients, spikes, or surges on properly installed, grounded

and code-compliant 120 volt power lines in the United States and Canada; transients, surges or spikes on

standard telephone land lines, PBX telephone equipment lines or Base 10T Ethernet lines, when properly

installed and connected. (This exclusion applies, for example, to ﬂuctuations in data transmission or

reception, by CATV or RF transmission or ﬂuctuations, or by transients in such transmission.)

3. Damage from any circumstance described as excluded above with respect to the CPS Product.

4. Damages from ﬁre, ﬂood, wind, rain, rising water, leakage or breakage of plumbing, abuse, misuse or

alteration of either the product or the Connected Equipment.

5. CyberPower excludes any liability for personal injury under the Limited Warranty and Connected Equipment

Guarantee. CyberPower excludes any liability for direct, indirect, special, incidental or consequential

damages, whether for damage to or loss of property [EXCEPT FOR (AND ONLY FOR) the speciﬁc limited

agreement of CyberPower to provide certain warranty beneﬁts regarding “Connected Equipment” under

this Warranty], loss of proﬁts, business interruption, or loss of information or data. NOTE: Some States or

Provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above

limitation may not apply to you.

6. The CPS Product is not for use in high-risk activities or with aquariums. The CPS Product is not designed or

intended for use in hazardous environments requiring fail-safe performance, or for use in any circumstance

in which the failure of the CPS Product could lead directly to death, personal injury, or severe physical or

property damage, or that would aect operation or safety of any medical or life support device (collectively,

“High Risk Activities”). CyberPower expressl disclaims any express or implied warranty of ﬁtness for High

Risk Activities or with aquariums. CyberPower does not authorize use of any CPS Product in any High Risk

Activities or with Aquariums. ANY SUCH USE IS IMPROPER AND IS A MISUSE OF THE PRODUCT.

Where can I get more information?

The application of the United Nations Convention of Contracts for the International Sale of Goods is expressly

excluded. CyberPower is the warrantor under this Limited Warranty. For further information please feel free to

contact CyberPower at Cyber Power Systems (USA), Inc. 4241 12th Ave E., STE 400, Shakopee, MN 55379;

call us at (877) 297-6937; or e-mail at: claims@cyberpowersystems.com.

FCC COMPLIANCE STATEMENT

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment o and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment to an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help

SYSTEM FUNCTION BLOCK DIAGRAM

TROUBLESHOOTING

TECHNICAL SPECIFICATIONS

FCC COMPLIANCE STATEMENT

LIMITED WARRANTY AND CONNECTED EQUIPMENT GUARANTEE

PROBLEM POSSIBLE CAUSE SOLUTION

Circuit breaker

button is

projecting from the

back of the unit.

Circuit breaker has tripped due

to an overload.

Turn the UPS o and unplug at least one piece

of equipment. Wait 10 seconds, reset the

circuit breaker by depressing the button, and

then turn the UPS on.

The UPS does not

perform expected

runtime.

Battery not fully charged. Recharge the battery by leaving

the UPS plugged in.

Battery is worn out. Please contact CyberPower Systems about

replacement batteries at tech@cpsww.com

The UPS will

not turn on.

The on/o switch is designed

to prevent damage from

rapidly turning it o and on.

Turn the UPS o. Wait 10 seconds and then

turn the UPS on.

The unit is not connected

to an AC outlet.

The unit must be connected to a

120 V 60 Hz outlet.

The battery is worn out. Please contact CyberPower Systems about

replacement batteries at tech@cpsww.com

Mechanical problem. Please contact CyberPower Systems

at tech@cpsww.com

PowerPanel®

Personal Edition

is inactive (all

icons are gray).

The USB cable is

not connected.

Connect the USB cable to the UPS unit and an

open USB port on the back of the computer.

You must use the cable that came with the unit.

The USB cable is connected

to the wrong port.

Check the back of the computer for an

additional USB port. Move the cable to this port.

The unit is not providing

battery power.

Shutdown your computer and turn the UPS o.

Wait 10 seconds and turn the UPS back on. This

should reset the unit.

The USB power

ports are not

providing power

to the connected

devices.

The USB power port has Over

Current Protection design.

When the total current of

connected devices is over

2.1A, the USB power ports will

stop providing power to the

connected devices.

Turn the UPS o and unplug at least one piece

of device connected to the USB power port and

then turn the UPS on.

SERIES CP825AVRLCD-G CP685AVRLCD-G CP800AVR CP685AVR-G

MODEL CP825AVRLCDa CP685AVRLCDa CP800AVRa CP685AVRa

Capacity 825 VA/450 W 685 VA/390 W 800 VA/450 W 685 VA/390 W

Nominal Input Voltage 120Vac

Input Frequency 60 Hz ± 3 Hz

On-Battery

Output Voltage 120Vac ± 5%

On-Battery

Output Frequency 60Hz +/- 1%

Max. Load for

UPS Outlets 825 VA/450 W 685 VA/390 W 800 VA/450 W 685 VA/390 W

Max. Load for Full-Time

Surge Protection outlets 12 Amps

On-Battery Output

Wave Form Simulated Sine Wave Form

Surge Protection 1030 Joules

Operating Temperature + 32°F to 104°F/0°C to 40°C

Operating Relative

Humidity 0 to 90% non-condensing

Size (W x H x D) 11.02” × 6.81” × 3.47”

Net Weight 12.74 lbs 11.62 lbs 12.74 lbs 11.62 lbs

Typical Battery

Recharge Time 8 hours typical from total discharge

Typical Battery Life 3 to 6 years, depending on number of discharge/recharge cycles

Recommended Battery Sealed Maintenance Free Lead Acid Battery

Safety Approvals UL1778(UPS), cUL107., FCC/DoC Class B

ADVANCED ENERGY-SAVING PATENTED BYPASS TECHNOLOGY

CyberPower’s patented GreenPower UPS™ with Bypass Technology reduces UPS energy

costs by up to 75% compared to conventional UPS models. Even when utility power

is normal, conventional UPS models constantly pass power through a transformer. By

contrast, under normal conditions the advanced circuitry of a GreenPower UPS™ bypasses

the transformer. As a result, the power eciency is signiﬁcantly increased while decreasing

waste heat, using less energy, and reducing energy costs. When an abnormal power

condition occurs, the GreenPower UPS™ automatically runs power through its transformer

to regulate voltage and provide “safe” power. Since utility power is normal over 88% of the

time, the GreenPower UPS™ operates primarily in its ecient bypass mode.

CYBERPOWER GREENPOWER UPSTM TECHNOLOGY

NORMAL MODE

BATTERY MODE

INPUT OUTPUT

EMI FILTER SURGE

PROTECTOR AVR

CHARGER

AC/DC INVERTER

BATTERY

K01-0000710-01

CyberPower encourages environmentally sound methods for disposal and recycling of its UPS

products. Please dispose and/or recycle your UPS and batteries in accordance to your local regulations.

This device is manufactured using environmentally-safe procedures in compliance with the Restriction

of Hazardous Substances directive.

For more information contact CyberPower at:

Cyber Power Systems (USA), Inc.

4241 12th Ave E., STE 400, Shakopee, MN 55379

Phone: (877) 297-6937; e-mail at: claims@cpsww.com.

PowerPanel® Personal Edition is a trademark

of Cyber Power Systems (USA) Inc.

the property of their respective owners.

IWARNING: This product can expose you to chemicals including bisphenol A (BPA) and styrene, which is known to the

State of California to cause reproductive harm and cancer. For more information, go to www.P65Warnings.ca.gov.

CyberPowerSystems.com

LINE MODE

FUNCTION SETUP GUIDE – SENSITIVITY SETUP

Product specificaties

Merk:	CyberPower
Categorie:	UPS
Model:	CP685AVRLCD
Gewicht:	6350 g
Vormfactor:	Compact
Aantal USB 2.0-poorten:	1
Aantal Ethernet LAN (RJ-45)-poorten:	1
Certificering:	UL1778, cUL 107.1, FCC DOC Class B
Geluidsalarm(en):	Ja
Responstijd:	4 ms
Uitgangsvermogen:	390 W
Accu/Batterij oplaadtijd:	8 uur
Temperatuur bij opslag:	-15 - 45 °C
Frequentie:	60 Hz
Gewicht (imperiaal):	14 lbs
Bedrijfstemperatuur, bereik:	32 - 95 °F
Afmetingen (B x D x H):	279.4 x 89 x 165 mm
Modem (RJ-11) poort:	1
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 95 procent
Batterijtechnologie:	Sealed Lead Acid (VRLA)
Afmetingen (B x D x H) (Brits):	11 x 3.5 x 6.5 "
Surge energy rating:	890 J
Input-connectietype:	NEMA 5-15P
Output power capacity:	0.685 kVA
UPS-topologie:	Line-interactive
Typische backup tijd op halve lading:	10 min
Typische backup tijd op volledige lading:	2 min
Hot-swap batterij:	Ja
Output-aansluitingen:	NEMA 5-15R
Vervangings-batterij cartridge:	BB - BP8-12