CyberPower CP685AVRG Handleiding

CyberPower UPS CP685AVRG

Lees hieronder de 📖 handleiding in het Nederlandse voor CyberPower CP685AVRG (2 pagina's) in de categorie UPS. Deze handleiding was nuttig voor 18 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

OVERVIEW

The CP825AVRLCDG/CP685AVRLCDG/

CP800AVR/CP685AVRG provides complete

power protection from utility power that is

not always consistent. The CP825AVRLCDG/

CP685AVRLCDG/CP800AVR/CP685AVRG

features 1030 Joules of surge protection. The

unit provides long lasting battery backup

during power outages with maintenance free

batteries. The CP825AVRLCD/CP685AVRLDG/

CP800AVR/CP685AVRG ensures consistent

power to your computer system and includes

software that will automatically save your

open ﬁles and shutdown your computer sys-

tem during a utility power loss.

HOW TO DETERMINE THE POWER REQUIRE-

MENTS OF YOUR EQUIPMENT

1. Ensure that the equipment plugged

into the UPS does not exceed the UPS

unit’s rated capacity (825VA/450W for

CP825AVRLCDG, 800VA/450W

for CP800AVR, 685VA/390W for

CP685AVRLCDG, CP685AVRG). If the rated

capacities of the unit are exceeded, an

overload condition may occur and cause

the UPS unit to shut down or the circuit

breaker to trip.

2. There are many factors that can aect

the amount of power that your electronic

equipment will require. For optimal system

performance keep the load below 80% of

the unit’s rated capacity.

HARDWARE INSTALLATION GUIDE

1. Your new UPS

may be used

immediately

upon receipt.

However, after

receiving a

new UPS, to ensure the battery’s maximum

charge capacity, it is recommended that

you charge the battery for at least 8 hours.

Your UPS is equipped with an auto-charge

feature. When the UPS is plugged into an AC

outlet, the battery will automatically charge

whether the UPS is turned on or turned o.

Note: This UPS is designed with a safety fea-

ture to keep the system from being turned

on during shipment. The ﬁrst time you turn

the UPS on, you will need to have it connect-

ed to AC power or it will not power up.

2. With the UPS unit turned o and un-

plugged, connect your computer, monitor,

and any other peripherals requiring battery

backup into the battery power supplied

outlets. Plug the other peripheral equip-

ment (eg. printer, scanner, speakers, etc.)

into the full-time surge protection outlets.

DO NOT plug a laser printer, paper shred-

der, copier, space heater, vacuum cleaner,

sump pump, or other large electrical device

into the “Battery and Surge Protected Out-

lets”. The power demands of these devices

will overload and possibly damage the unit.

3. Plug the UPS into a 2-pole, 3-wire grounded

receptacle (wall outlet). Make sure the wall

branch outlet is protected

by a fuse or circuit break-

er and does not service

equipment with large

electrical demands (e.g.

air conditioner, refrigerator, copier, etc.).

The warranty prohibits the use of extension

cords, outlet strips, and surge strips in con-

junction with the UPS unit.

4. Press the power switch to turn the unit on.

The Power On indicator light will illuminate

green and the unit will “beep” once.

5. If an overload is detected, an audible alarm

will sound and the unit will emit one long

beep. To correct this, turn the UPS o and

unplug at least one piece of equipment

from the battery power supplied outlets.

Make sure the circuit breaker is depressed

and then turn the UPS on.

6. To maintain optimal battery charge,

leave the UPS plugged into an AC outlet

at all times.

7. To store the UPS for an extended period

of time, cover it and store with the battery

fully charged. While in storage, recharge

the battery every three months to ensure

optimal battery life.

8. Ensure the wall outlet and UPS are locat-

ed near the equipment being attached for

proper accessibility.

YOUR ULTIMATE ALLY IN POWER

Cyber Power Systems (USA), Inc.

4241 12th Avenue East, Suite 400 | Shakopee, MN 55379 | CyberPowerSystems.com

AVR UPS SERIES

CP825AVRLCDG / CP685AVRLCDG / CP800AVR / CP685AVRG

USER MANUAL

FEATURES

1. Power Switch

2. Power On Indicator

3. Mode Switch

For CP825AVRLCDG / CP685AVRLCDG

4. Fault Indicator

5. Mute Button

For CP800AVR / CP685AVRG

6. LCD module display

For CP825AVRLCDG / CP685AVRLCDG

7. Battery and Surge Protected Outlets

8. Full-Time Surge Protection Outlets

9. USB Port

10. Communication Protection Ports

For CP825AVRLCDG

11. Serial Port

12. Circuit Breaker and Reset

13. Ground Screw

14. Outlets Designed for AC Adapters

Thank you for purchasing a CyberPower product. This UPS is designed to provide unsurpassed

power protection, operation, and performance during the lifetime of the product. Please take

a few minutes to register your product at: www.CyberPowerSystems.com/registration. Regis-

tration certiﬁes your product’s warranty, conﬁrms your ownership in the event of a product loss

or theft, and entitles you to free technical support. Register your product now to receive the

beneﬁts of CyberPower ownership.

CAUTION! To prevent the risk of ﬁre or

electric shock, install in a temperature and

humidity controlled indoor area free of

conductive contaminants. (Please see

speciﬁcations for acceptable temperature

and humidity range).

CAUTION! To reduce the risk of electric shock,

do not remove the cover except to service the

battery. Turn o and unplug the unit before

servicing the batteries. There are no user ser-

viceable parts inside except for the battery.

CAUTION! Hazardous live parts inside can be

energized by the battery even when the AC

input power is disconnected.

CAUTION! The UPS must be connected to an

AC power outlet with fuse or circuit breaker

protection. Do not plug into an outlet that is

not grounded. If you need to de-energize this

equipment, turn o and unplug the unit.

CAUTION! To avoid electric shock, turn o the

unit and unplug it from the AC power source

before connecting equipment to the unit.

CAUTION! To reduce the risk of ﬁre, connect

only to a circuit provided with 20 amperes

maximum branch circuit over current protec-

tion in accordance with the National Electric

Code, ANSI/NFPA 70.

CAUTION! Not for use in a computer room as

deﬁned in the Standard for the Protection of

Electronic Computer / Data Processing Equip-

ment, ANSI/NFPA 75.

CAUTION! Do not dispose of batteries in a ﬁre.

The batteries may explode.

CAUTION! Do not open or mutilate batteries.

Released electrolyte is harmful to the skin and

eyes. It may be toxic.

DO NOT USE FOR MEDICAL

OR LIFE SUPPORT EQUIPMENT!

CyberPower Systems does not sell products

for life support or medical applications. DO

NOT use in any circumstance that would aect

operation and safety of life support equip-

ment, any medical applications or patient care.

DO NOT USE WITH OR NEAR AQUARIUMS!

To reduce the risk of ﬁre or electric shock, do

not use with or near an aquarium. Condensa-

tion from the aquarium can cause the unit to

short out.

DO NOT USE THE UPS

ON ANY TRANSPORTATION!

To reduce the risk of ﬁre or electric shock, do

not use the unit on any transportation such

as airplanes or ships. The eect of shock or

vibration caused during transit and the damp

environment can cause the unit to short out.

PRODUCT REGISTRATION

IMPORTANT SAFETY WARNINGS (SAVE THESE INSTRUCTIONS)

This manual contains important safety instructions. Please read and follow all instructions carefully

during installation and operation of the unit. Read this manual thoroughly before attempting to

unpack, install, or operate your UPS.

INSTALLING YOUR UPS SYSTEM - continued

UNPACKING

Inspect the UPS upon receipt.

The box should contain the following:

(a) UPS unit

(b) User’s manual

PowerPanel® Personal software is

available on our website. Please visit

www.cyberpowersystems.com and go

to the Software Section for a free download.

AUTOMATIC VOLTAGE REGULATOR

The CP825AVRLCDG/CP685AVRLCDG/

CP800AVR/CP685AVRG stabilizes inconsistent

utility power to nominal levels that are safe for

equipment. Unstable utility power can be dam-

aging to important data and hardware.

With Automatic Voltage Regulation (AVR),

damaging voltage levels

are corrected to safe

levels. AVR automatically

increases low utility power

to a consistent and safe

110/120 volts.

BASIC OPERATION

INSTALLING YOUR UPS SYSTEM

1. Power Switch:

Used as the master on/o switch for equip-

ment connected to the battery power sup-

plied outlets. To turn the UPS ON, press the

power button for approximately 2 seconds

- you will hear a constant tone (1 second) -

and release after a short beep.

To turn the UPS OFF, press the power

button for approximately 2 seconds - you

will hear a constant tone (1 second) - and

release after two short beeps.

Alarm setting (For CP825AVRLCDG/

CP685AVRLCDG): The audible alarm can

be turned O or On by double clicking

the POWER button. The default setting is

for the Alarm On. To turn the Alarm O,

double click the button. You will hear two

short beeps when the Alarm is turned o.

To turn the Alarm back On, double click the

button. You will hear a single short beep

when the Alarm is turned on. *When the

Alarm is turned O, there will be no audible

notiﬁcation when the UPS reaches a low

battery state.

2. Power On Indicator:

This LED is illuminated when the utility

power is normal and the UPS outlets are

providing power, free of surges and spikes.

3. Mode Switch

(For CP825AVRLCDG/CP685AVRLCDG):

Press the Mode Switch for approximately

3 seconds to enter setup mode to view

options: Utility High/low Voltage range,

sensitivity setup, LCD sleep ON/OFF, bat-

tery test, buzzer ON/OFF, and low battery

alarm. When an option is selected, wait for

8 seconds for the setting to be conﬁrmed.

After the setting has been conﬁrmed the

LCD screen will leave setup mode and go

back to status display. If there is no action

for 8 seconds during setup, the LCD will

also leave setup mode and go back to the

status display.

4. Fault Indicator:

This LED is illuminated if there is a problem

with the UPS.

5. Mute Button

(For CP800AVR/CP685AVRG):

Press the button for 2 seconds to enable

the audible alarm (beeps once) or disable

(beeps twice) the audible alarm.

6. LCD module display

(For CP825AVRLCDG/CP685AVRLCDG):

LCD display shows all the UPS information

using icons and messages. For more infor-

mation please review the “Deﬁnitions for

Illuminated LCD Indicators” section.

7. Battery and Surge Protected Outlets:

The unit has four battery powered and

surge protected outlets to ensure tempo-

rary uninterrupted operation of your equip-

ment during a power failure.

8. Full-Time Surge Protection Outlets:

The unit has four surge suppression outlets.

9. USB Port:

The USB port allows connection and com-

munication between the USB port on the

computer and the UPS unit.

10. Communication Protection Ports

(For CP825AVRLCDG):

Communication protection ports, bidirec-

tional, will protect a 10/100/1000 Ethernet

connection (RJ45).

11. Serial Port:

Serial Port allow for bi-directional commu-

nication among the UPS and the comput-

er.The UPS can control the computer’s

shutdown in case of an emergency, and at

the same time, the computer can monitor

the UPS and alter its various programmable

parameters.

12. Circuit Breaker and Reset:

Located on the side of the UPS, the

circuit breaker provides overload and

fault protection.

13. Ground Screw:

The ground screw is used for any

equipment that needs a chassis ground

connection.

14. Outlets Designed for AC Adapters:

The UPS unit has four widely-spaced out-

lets. AC power adapters can be plugged

into the UPS without overlapping or block-

ing adjacent outlets.

3 4

CP825AVRLCDG

CP685AVRLCDG

CP800AVR

CP685AVRG

Replacement of batteries located

in an OPERATOR ACCESS AREA

1. When replacing batteries, replace with

the same number of the following battery:

CyberPower/RB1290 for CP825AVRLCDG,

CP800AVR; CyberPower/RB1270B for

CP685AVRLCDG, CP685AVRG.

2. Risk of Energy Hazard, 12V, CAUTION!

maximum 9 Ampere-hour battery. Before

replacing batteries, remove conductive

jewelry such as chains, wrist watches, and

rings. High energy through conductive

materials could cause severe burns.

3. CAUTION! Do not dispose of batteries in a

ﬁre. The batteries may explode.

4. CAUTION! Do not open or mutilate batter-

ies. Released material is harmful to the skin

and eyes. It may be toxic.

5. CAUTION! A battery can present a risk of

electrical shock and high short circuit cur-

rent. The following precautions should be

observed when working on batteries:

(1) Remove watches rings, or other metal

objects.

(2) Use tools with insulated handles.

CAUTION - RISK OF EXPLOSION IF BATTERY

IS REPLACED BY AN INCORRECT TYPE.

DISPOSE OF USED BATTERIES ACCORDING

TO LOCAL REGULATIONS.

TROUBLESHOOTING - continued

Problem Possible Cause Solution

Circuit breaker button is

projecting from the back of the

unit.

Circuit breaker has been tripped

due to an overload.

Turn the UPS o and unplug at

least one piece of equipment.

Wait 10 seconds, reset the circuit

breaker by pressing the button,

and then turn the UPS on.

The UPS does not perform

expected runtime.

Battery not fully charged. Recharge the battery by leaving

the UPS plugged in.

Battery is worn out.

Contact CyberPower Systems

about replacement batteries at:

cyberpowersystems.com/support.

Additional troubleshooting information can be found at “Support” at www.CyberPowerSystems.com

LOAD CAPACITY Meter: This meter displays

the approximate output load level of the UPS

battery outlets in 20% increments.

SENSITIVITY Meter: This meter displays the

sensitivity level of the UPS. It is to control the

sensitivity of the UPS to switch to Battery

Mode by selecting UPS shutdown voltage

range. When the sensitivity is increased, the

UPS will switch to Battery Mode with less

input power variation.

FAULT: The following number appears if there

is a problem with the UPS. Press the POWER

button to turn the UPS o.

DEFINITIONS FOR ILLUMINATED LED INDICATORS TECHNICAL SPECIFICATIONS - continued - continued

REPLACING THE BATTERY

TROUBLESHOOTING

Problem Possible Cause Solution

The UPS will not turn on.

The on/o switch is designed

to prevent damage from rapidly

turning it o and on.

Turn the UPS o. Wait 10 seconds

and then turn the UPS on.

The unit is not connected to an

AC outlet.

The unit must be connected to a

120V 60Hz outlet.

The battery is worn out.

Contact CyberPower Systems

about replacement batteries at:

cyberpowersystems.com/support.

Mechanical problem. Contact CyberPower Systems at:

cyberpowersystems.com/support.

PowerPanel® Personal is inactive

(all icons are gray).

The USB cable is not connected.

Connect the USB cable to the UPS

unit and an open USB port on the

back of the computer.

The USB cable is connected to a

bad USB port.

Check for a dierent USB port and

plug the cable in.

The unit is not providing

battery power.

Shutdown your computer and turn

the UPS o. Wait 10 seconds and

turn the UPS back on. This should

reset the unit.

The USB power ports are not

providing power to the connect-

ed devices.

The USB power port has Over Cur-

rent Protection design. When the

total current of connected devices

is over 2.1A, the USB power ports

will stop providing power to the

connected devices.

Turn the UPS o and unplug at

least one piece of device connect-

ed to the USB power port and

then turn the UPS on.

TECHNICAL SPECIFICATIONS

Advanced Energy-Saving Design

The GreenPower UPS™ has a high-eciency charger, which makes it the most energy-ecient UPS in its class. The advanced high-frequency

charging system signiﬁcantly improves charging eciency and conserves energy. As a result of this advanced design, the GreenPower UPS™

uses less energy compared to competitive models. The GreenPower UPS™ is manufactured in accordance with the Restriction on Hazardous

Substances (RoHS) directive making it one of the most environmentally-friendly UPS systems on the market today.

CYBERPOWER GREENPOWER UPS™ TECHNOLOGY

REEN

OWER

UPS

™

Energy-Saving Tec hnolo gy

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment to an outlet on a circuit dierent from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Warning: Changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Canadian Compliance Statement

CAN ICES-3 (B)/NMB-3(B)

FCC COMPLIANCE STATEMENT

Please visit www.CyberPowerSystems.com for a copy of the Limited Warranty and Connected Equipment Guarantee.

Where Can I Get More Information?

The application of the United Nations Convention of Contracts for the International Sale of Goods is expressly excluded.

CyberPower is the warrantor under this Limited Warranty. For further information please feel free to contact CyberPower at:

Cyber Power Systems (USA), Inc. 4241 12th Ave E., STE 400, Shakopee, MN 55379;

call us at (877) 297-6937; or submit a web ticket online at cyberpowersystems.com/support.

Cyber Power Systems (USA), Inc. encourages environmentally sound methods for disposal and recycling of its UPS products.

Please dispose and/or recycle your UPS and batteries in accordance to the local regulations of your state.

LIMITED WARRANTY AND CONNECTED EQUIPMENT GUARANTEE

7 8

INPUT Voltage Meter: This meter measures

the AC voltage that the UPS system is re-

ceiving from the utility wall outlet. The UPS

is designed to continuously supply connect-

ed equipment with stable output voltage. In

the event of a complete power loss, severe

planned power suppression, or over-voltage,

the UPS relies on its internal battery to supply

consistent 110/120 output voltage. The INPUT

voltage meter can be used as a diagnostic tool

to identify poor-quality input power.

OUTPUT Voltage Meter: This meter measure,

in real time, the AC voltage that the UPS

system is providing to the computer during

normal AC/Utility Power mode, and battery

backup mode.

ESTIMATED RUNTIME: This displays the run

time estimate of the UPS with the current

battery capacity and load.

NORMAL Icon: This icon appears when the

UPS is working under normal conditions.

BATTERY Icon: During a severe planned pow-

er suppression or power outage, this icon ap-

pears and an alarm sounds (two short beeps

followed by a pause) to indicate the UPS is

operating from its internal batteries. During

a prolonged

planned power

suppression or

power outage,

the alarm will

sound con-

tinuously to

indicate the

UPS’s batter-

ies are nearly out of power. You should save

ﬁles and turn o your equipment immediately

or allow the software to shut the system down.

OVER LOAD Icon: This icon appears and an

alarm sounds to indicate the battery-supplied

outlets are overloaded. To clear the overload,

unplug some of your equipment from the bat-

tery-supplied outlets until the icon turns o

and the alarm stops.

BATTERY CAPACITY Meter: This meter

displays the approximate charge level of the

UPS’s internal battery in 20% increments.

During a power outage or severe planned

power suppression, the UPS switches to bat-

tery power (the BATTERY icon appears) and

the battery charge level decreases.

continued

DEFINITIONS FOR ILLUMINATED LED INDICATORS

TO REPLACE THE BATTERY

1. Turn o and unplug all connected equipment.

2. Unplug it from the AC power source.

3. Turn the UPS upside down.

4. Remove the 1 retaining screw.

5. Slide the battery compartment cover completely

o of the unit.

6. Remove the battery from the compartment.

7. Disconnect the battery cables from the battery.

8. Install the replacement battery by connecting the red

wire and black wire to the positive (+) and negative (-)

terminal of the battery.

9. Put the battery back into the compartment.

10. Slide back the battery compartment cover and tighten the retaining screw.

11. Charge the unit for 8 hours to fully charge the battery.

REMINDER: Batteries are considered HAZARDOUS WASTE and must be disposed of properly.

Most retailers that sell lead-acid batteries collects used batteries for recycling, as required by

local regulations.

The LCD display indicates a variety of UPS operation-

al conditions. All descriptions apply when the UPS is

plugged into an AC outlet and turned on or when the

UPS is on battery.

Series CP825AVRLCDG CP685AVRLCDG CP600AVR CP685AVR

Model CP825AVRLCDa CP685AVRLCDGa CP800AVRa CP685AVRa

Capacity 825 VA/450 W 685 VA/390 W 800 VA/450 W 685 VA/390 W

Nominal Input Voltage 120 V

Input Frequency 60 Hz ± 3 Hz

On-Battery Output Voltage 120 VAC ± 5%

On-Battery Output Frequency 60 Hz ± 3 Hz

Max. Load for UPS Outlets 825 VA/450 W 685 VA/390 W 800 VA/450 W 685 VA/390 W

Max. Load for Full-time

Surge Protection Outlets 12 Amps

On-Battery Output Wave Form Simulated Sine Wave

Surge Protection 1030 J

Operating Temperature + 32°F to 104° F / 0° C to 40° C

Operating Relative Humidity 0 to 90% non-condensing

DEFINITIONS FOR LED INDICATORS & AUDIBLE ALARMS

POWER WIRING FAULT ALARM

CONDITION

On O O Normal

On O

Beep

twice every

30 seconds

Utility Failure - Battery Mode: The UPS is providing power to

battery power-supplied outlets from its battery.

On O

Rapid

beeping every

1/2 second

Utility Failure - Low Battery: The UPS is providing battery pow-

er. Rapid beeping indicates the unit will run out of power soon.

On/O

Flash once

every 5

seconds

Constant tone

Battery Mode or AC/Utility Power Mode Overload Fault:

Occurs when connected equipment exceeds the rating of

battery outlets of the unit. Please unplug at least one piece

of equipment from battery outlets..

O

Flash twice

every 5

seconds

Constant tone

Battery Output Short Fault: Please unplug at least one

piece of equipment from battery outlets and turn on the

UPS again. If the fault still exists, please contact Cyber-

Power Systems for support.

Flash 3

times every

5 seconds

Constant tone Charger Fault: Contact CyberPower Systems for support.

Series CP825AVRLCDG CP685AVRLCDG CP600AVR CP685AVR

Model CP825AVRLCDa CP685AVRLCDGa CP800AVRa CP685AVRa

Size (W x H x D) 11.02” x 6.81” x 3.47” / (100 x 280 x 355 mm)

Net Weight 12.74 lbs. 11.62 lbs. 12.74 lbs. 11.62 lbs.

Typical Battery Recharge Time 8 hours typical from total discharge

Typical Battery Life 3 to 6 years, depending on number of discharge/recharge cycles

Recommended Battery Sealed Maintenance Free Lead Acid Battery

Safety Approvals UL1778(UPS), cUL107, FCC/DoC Class B

SYSTEM FUNCTION BLOCK DIAGRAM

Input Output

Battery Mode

Normal Mode

EMI

Filter

Surge

Suppressor

Inverter

Charger

AC / DC

Battery

AVR

Product specificaties

Merk:	CyberPower
Categorie:	UPS
Model:	CP685AVRG
Kleur van het product:	Zwart
Gewicht:	5300 g
Breedte:	11 mm
Diepte:	3.5 mm
Hoogte:	6.8 mm
LED-indicatoren:	Ja
Vormfactor:	Compact
USB-poort:	Ja
Meegeleverde kabels:	Stroomingangskabel
Accu/Batterij voltage:	12 V
Geluidsalarm(en):	Ja
Responstijd:	4 ms
Duurzaamheidscertificaten:	RoHS
Uitgangsvermogen:	390 W
Batterij capaciteit:	7 Ah
Accu/Batterij oplaadtijd:	8 uur
Frequentie:	57/63 Hz
Veiligheid:	UL1778, cUL 107.3, FCC DOC Class B
Seriële poort(en):	1
Stekker:	NEMA 5-15P
Bedrijfstemperatuur (T-T):	0 - 35 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 90 procent
Batterijtechnologie:	Sealed Lead Acid (VRLA)
Aantal batterijcellen:	1
Surge energy rating:	1030 J
Aantal AC uitgangen:	8 AC-uitgang(en)
Output power capacity:	0.685 kVA
Ingang operation voltage (min):	90 V
Ingang operation voltage (max):	140 V
Uitgang operation voltage (min):	120 V
Uitgang operation voltage (max):	120 V
UPS-topologie:	Line-interactive
Typische backup tijd op halve lading:	11 min
Typische backup tijd op volledige lading:	2 min
Seriële interface:	Ja
Output frequentie:	50/60 Hz
Hoorbare alarmstanden:	Low battery alarm, Overload alarm
Uitgangsspanningsregeling:	5 procent
Spanningsbeveiliging:	Ja
Golfvorm:	Sinus
Automatic Voltage Regulation (AVR):	Ja
Vervangings-batterij cartridge:	RB1270B