Ctek D250TS Handleiding

Ctek Batterij-oplader D250TS

Lees hieronder de 📖 handleiding in het Nederlandse voor Ctek D250TS (7 pagina's) in de categorie Batterij-oplader. Deze handleiding was nuttig voor 43 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/7
EN
EN • 3
MANUAL
CONGRATULATIONS
Congratulations on purchasing your new CTEK professional 24V DC/DC switch mode battery
charger, 12V converter and battery equalizer. This charger is part of a range of professional bat-
tery chargers from CTEK SWEDEN AB. It represents the latest technology in battery charging with
charging and analysis in 4 steps with temperature compensation.
Read this User Manual and follow the instructions carefully before using your new charger.
SAFETY
• The charger is designed for 24V lead-acid batteries mounted into vehicles.
Do not use the charger for any other purpose
• Use safety glasses when connecting or disconnecting a battery.
• Battery acid is corrosive. Rinse immediately with water if acid comes into contact with skin
or eyes. Seek medical advice.
• Make sure that the cables are not being pinched or in contact with warm surfaces
or sharp edges.
• While charging, a battery can emit explosive gases, avoid sparks in the immediate area.
• Always provide for proper ventilation during charging.
• Avoid covering the charger.
Starter Battery
24V+
Service Battery
24V+
Service ground Service Battery Midpoint
D250TS
The D250TS has one 24V input and two alternating outputs. One output charge a 24V
battery and the other provides 50% of the input voltage to the midpoint of a 24V system. This
enables connection of 12V consumers to the battery string and also equalizing this battery
string, for longer battery life.
D250TS
FEATURES:
• Multi-step10A temperature compensated battery charging and battery maintenance.
• Battery separation of Starter and Service batteries.
• Equalization of Service batteries
• Makes connection of 12V consumers directly to 24V Service battery possible.
• When the charger is correctly connected the charger will output 24V on the status signal wire.
Connection of a 24V lamp (max 2W) to the status signal wire will indicate a correctly con-
nected charger.
• The charger will maintain the starter battery untill the supply is below 14V. To avoid draining the
service battery always connect a charger to the service battery when the vehicle is not used for
a longer period.
+IN +OUT
EQU
D250TS
Status signal wire
Temperature sensor
20015884C D250TS, Manual, Print file 002.indd 3 2011-12-20 13:27:12
4 • EN
INSTALLATION OF UNIT
1. Attach the temperature sensor holder on a flat surface on one Starter battery. Position it as close
as possible to a positive post.
2. Use the included drill template. Wiring is simplified if the units are installed according to the drill
template, but other setups are possible.
3. Install the unit(s) on a flat surface where it can be properly fixed and where the unit is not
exposed to fuels, oils or splashes of dirt.
4. Mount the unit with screws intended for the surface and attach it with one screw in each of the
four holes in the corners of the unit. See picture 1. Mount the unit with M4 or ST4.2 screws. The
required torque depends on the surface for mounting.
Figure 1
2Nm
DRILL TEMPLATE
Ø 5mm
168
mm
90,6
mm
Service ground
Service Battery
24V+
Starter Battery
24V+
Status signal wire
Temp sensor
Service Battery Midpoint
20015884C D250TS, Manual, Print file 002.indd 4 2011-12-20 13:27:13
EN
EN • 5
FUNCTIONALITY
The D250TS has three operating modes:
1. 4-step charging of a Starter battery.
2. When Starter battery is fully charged: Equalization of a Service battery on the Input side. This
function provides the possibility to connect 12V consumers to the 1st battery in the Service
battery string.
3. Monitoring. The D250TS now monitors if the Starter battery needs charging (priority) or the
Service battery needs equalization.
B-1 B-2
B-3
IN
GNC A
OUT
c2
c1
DC/DC
24V/1CA
ALTERNATOR
STARTER MOTOR
SERVICE
BATTERY
SERVICE
BATTERY
STARTER
BATTERY
STARTER
BATTERY
20015884C D250TS, Manual, Print file 002.indd 5 2011-12-20 13:27:13

Product specificaties

Merk: Ctek
Categorie: Batterij-oplader
Model: D250TS

Heb je hulp nodig?

Als je hulp nodig hebt met Ctek D250TS stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Batterij-oplader Ctek

Ctek

Ctek READY AUTOMOTIVE Handleiding

25 April 2024
Ctek

Ctek Smartpass 120T Handleiding

12 Juni 2023
Ctek

Ctek CS ONE Handleiding

4 Juni 2023
Ctek

Ctek CT5 Handleiding

4 Juni 2023
Ctek

Ctek MXT 14 Handleiding

15 Mei 2023
Ctek

Ctek M15 Handleiding

6 Mei 2023
Ctek

Ctek D250T Handleiding

6 Mei 2023
Ctek

Ctek Pro Battery Tester Handleiding

4 Mei 2023
Ctek

Ctek Bumper 120 Handleiding

1 Mei 2023
Ctek

Ctek XS 7000 Handleiding

27 April 2023

Handleiding Batterij-oplader

Nieuwste handleidingen voor Batterij-oplader

Hama

Hama 210594 Handleiding

20 December 2024
Hama

Hama 210290 Handleiding

20 December 2024
Hama

Hama 201634 Handleiding

20 December 2024
NOCO

NOCO Genius GX2440 Handleiding

14 December 2024
IDX

IDX ZC-X2G Handleiding

10 December 2024
IDX

IDX UC-PD2 Handleiding

10 December 2024
Black Decker

Black Decker 98020 Handleiding

8 December 2024
Anker

Anker 613 Magnetic Wireless Charger Handleiding

7 December 2024
Ansmann

Ansmann Jump Starter 10.0 Handleiding

4 December 2024
Einhell

Einhell BT-BC 4 D Handleiding

4 December 2024