Ctek CT5 Powersport Handleiding

Ctek Batterij-oplader CT5 Powersport

Lees hieronder de 📖 handleiding in het Nederlandse voor Ctek CT5 Powersport (7 pagina's) in de categorie Batterij-oplader. Deze handleiding was nuttig voor 42 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/7

EN • 3

MANUAL

CONGRATULATIONS

to the purchase of your new professional switch mode battery charger. This charger is

included in a series of professional chargers from CTEK SWEDEN AB and represents the

latest technology in battery charging.

Read safety instruction

HOW TO CHARGE

1. Connect the charger to the battery.

For batteries mounted inside a vehicle

1. Connect the charger according to the

vehicles manual.

2. Connect the charger to the wall socket.

3. Disconnect the charger from the wall socket

before disconnecting the battery.

4. Disconnect the black clamp before the red

clamp.

1 2

2. Connect the charger to the wall socket. The power lamp will indicate that the mains

cable is connected to the wall socket. The power lamp will blink if the battery clamps

are incorrectly connected. The reverse polarity protection will ensure that the battery or

charger will not be damaged.

RECOND LITHIUMNORMAL

NORMAL

BAT T ERY

PROG RA M

ERROR LAMP

RECOND

OPT ION

FULLY CHARGED

LITHIUM

BAT T ERY

PROG RA M

POWER LAMP

MODE BUT T ON

3. Press the MODE-button to select charging program.

NORMAL BATTERY PROGRAM LITHIUM BATTERY PROGRAM

Continue to press the MODE-button to combine charging program with charging options.

RECOND OPTION

Press the MODE-button several times until the desired combination of charging program

and options are lit.

4. Follow the display through the charging process.

The battery is fully charged when the CARE lamp is lit.

5. Stop charging at any time by disconnecting the mains cable from the wall socket.

4 • EN

CHARGING PROGRAMS

Settings are made by pressing the MODE-button. After about two seconds the charger acti-

vates the selected program. The selected program will be restarted next time the charger

is connected.

The table explains the diﬀerent Charging Programs:

Program Explanation

Normal battery program 14.4V/2.3A

Only for lead-acid batteries.

Recond option 15.8V/0.9A

Use to restore capacity to WET and Ca/Ca batteries. Recond your

battery once per year and after deep discharge to maximise lifetime and

capacity.

READY TO USE

The table shows the estimated time for empty battery to 80% charge.

BATTERY SIZE (Ah) TIME TO 80% CHARGED

5Ah 2h

10Ah 4h

15Ah 6h

20Ah 7h

25Ah 9h

POWER LAMP

If the power lamp is lit with a:

1. STEADY LIGHT

The mains cable is connected to the wall socket.

2. FLASHING LIGHT

The charger has entered the energy save mode. This happens if the

charger can’t detect a battery in 2 minutes.

ERROR LAMP

If the error lamp is lit, check the following:

1. Polarity error: Is the charger’s positive lead connected to

the positive charging point?Is the charger’s negative lead

connected to the negative charging point?

2. Is the charger connected to a 12V battery?

3. Has charging been interrupted in STEP 1, 2 or 5?

Restart the charger by pressing the MODE-button. If charging is still

being interrupted, the battery...

CHECK: ...is seriously sulphated and can not accept charge. The

battery may need to be replaced.

CARE: ...can not keep charge. The battery may need to be replaced.

LEAD-ACID

EN • 5

STEP 1 DESULPHATION

Detects sulphated batteries. Pulsing current and voltage, removes sulphate from the lead

plates of the battery restoring the battery capacity.

STEP 2 SOFT START

Tests if the battery can accept charge. This step prevents that charging proceeds with a

defect battery.

STEP 3 BULK

Charging with maximum current until approximately 80% battery capacity.

STEP 4 ABSORPTION

Charging with declining current to maximize up to 100% battery capacity.

STEP 5 ANALYZE

Tests if the battery can hold charge. Batteries that can not hold charge may need to be

replaced.

STEP 6 RECOND

Choose the Recond program to add the Recond step to the charging process. During the

Recond step voltage increases to create controlled gassing in the battery. Gassing mixes

the battery acid and gives back energy to the battery.

STEP 7 FLOAT

Maintaining the battery voltage at maximum level by providing a constant voltage charge.

STEP 8 PULSE

Maintaining the battery at 95–100% capacity. The charger monitors the battery voltage

and gives a pulse when necessary to keep the battery fully charged.

12345678

15.8V 2.3A until 12.6V Increasing voltage to

14.4V. 2.3A

Declining current

14.4V

Voltage limit 12V 13.6V

2.3A

12.7V–14.4V

2.3A–1.0A

Max 15.8V

0.9A

Time limit: Max 4h Max 20h 16h 3 minutes 2h or 6h 10 days Max 1h pulse.

Auto pulse every 24h

LEAD-ACID

Product specificaties

Merk:	Ctek
Categorie:	Batterij-oplader
Model:	CT5 Powersport
Kleur van het product:	Zwart
Ingebouwd display:	Nee
Internationale veiligheidscode (IP):	IP65
LED-indicatoren:	Bezig met opladen
Oplaadspanning:	12 V
Output current:	2.3 A
AC-ingangsspanning:	220 - 240 V
AC-ingangsfrequentie:	50 - 60 Hz
Accucapaciteit (min):	5 Ah
Accucapaciteit (max):	25 Ah