Chord CG-10 Handleiding

Chord Gitaar CG-10

Lees hieronder de 📖 handleiding in het Nederlandse voor Chord CG-10 (4 pagina's) in de categorie Gitaar. Deze handleiding was nuttig voor 63 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

CG SERIES

Guitar Amplifiers

Item ref: - - 173.044 CG 10 UK

CG- - 173.045 15 UK

CG- - 173.046 30 UK

CG- - 173.048 60 UK

User Manual

Version 1.1

Caution: Please read this manual carefully before operating

Damage caused by misuse is not covered by the warranty

173.044 , 173.045 , 173.046 , 173.048 User Manual UK UK UK UK

Introduction

Thank you for choosing our CG series guitar amplifier. Please read this manual prior to use to avoid damage to the item.

The CG range is specifically designed to give the guitar player a practical and powerful amplifier with classic tones.

Warning

To prevent the risk of fire or electric shock, do not expose this appliance to rain or moisture. To prevent electric shock do

not remove the cover. No user serviceable parts inside. Refer servicing to qualified service personnel.

Safety

• Prior to connecting mains, ensure that the supply voltage is correct and the mains lead is in good condition.

• Avoid ingress of water or particles into the enclosure.

• If the mains fuse blows, refer the unit to qualified service personnel

• Keep the unit out of direct sunlight and away from heat sources.

• Place the unit in an upright position during use and storage.

• Keep the unit away from moisture or dusty environments.

Cleaning

Use a soft cloth with a neutral detergent to clean the cabinet, panel and controls.

To avoid damage, do not use solvents to clean this equipment.

Control Panel

Rear Panel

1. INPUT 6.3mm jack (unbalanced) –

2. VOLUME Volume for CLEAN channel –

3. BASS + TREBLE Tone controls for clean channel –

4. CH/SEL Channel switch CLEAN - OVERDRIVE –

5. GAIN Input drive level for OVERDRIVE channel or DRIVE effect –

6. DRIVE Switch for engaging the drive effect –

7. VOLUME Master volume control –

8. EQ Section BASS, MIDDLE (CONTOUR for -60) and TREBLE tone controls –CG

9. REVERB Level control for internal spring reverb effect –

10. AUX IN twin RCA line level input for playback devices like mp3 players etc. –

11. FOOT SWITCH 6.3mm jack input for channel footswitch –

12. HEADPHONES 6.3mm stereo jack headphone output (mutes the speaker for silent practice) –

13. POWER power switch and indicator –

14. SEND/RETURN Loop for external effects (6.3mm jack, unbalanced)–

173.044 , 173.045 , 173.046 , 173.048 User Manual UK UK UK UK

Operation

• Connect the guitar to the CG-series amplifier input using a good quality 6.3mm mono jack lead. Otherwise, if effect

pedals are to be used, plug into these first (unless they are to be used in the effects loop) and plug the output from

these to the input of the amplifier.

• Connect the amplifier to the mains using the appropriate mains IEC lead supplied.

• If any external effects are to be used in the effects loop, connect the Send/Return jacks to the input/output of the

unit(s) and power up ready for use.

• Set VOLUME, GAIN and REVERB controls to the minimum (fully anticlockwise) position.

• Turn the BASS, MIDDLE, TREBLE and CONTOUR controls to the mid-way position.

• Switch on the POWER and switch the channel to CLEAN (make sure the DRIVE switch is off for CG-10). For CG-60

and CG-30, this can be achieved by plugging a footswitch into the 6.3mm FOOT SWITCH jack and pressing the

switch.

• Increase VOLUME for the clean channel and play a note, ensuring that the guitar’s volume and tone controls are

turned up. Continue increasing VOLUME until the required signal level is achieved.

• For CG-60, adjusting the left-most BASS and TREBLE controls adjusts the tone for the clean channel.

• Switch the CHANNEL or DRIVE switch to the overdrive channel or effect and turn up the GAIN to the desired drive

level whilst adjusting the VOLUME to balance the output level to suit. Note that higher gain and lower volume can

give more distortion.

• Adjust BASS, MIDDLE and TREBLE controls to achieve the desired tone. On the CG-60, the CONTOUR control adjusts

the response curve of the mid frequencies.

• Turn the REVERB control up to the required level to introduce the internal spring reverb effect to the sound.

• Plugging a line level source into the AUX twin RCA input mixes it with the guitar’s signal without adding overdrive or

tone shaping to the AUX signal. This may be a playback device, such as an mp3 player or CD player or even a drum

machine to play along with.

• Plugging in a pair of headphones to the 6.3mm TRS Phones jack will allow silent practice by muting the speaker

output.

• Before switching off or removing power, turn down the VOLUME controls.

• When not in use, switch off and disconnect from the mains.

Product specificaties

Merk:	Chord
Categorie:	Gitaar
Model:	CG-10
Kleur van het product:	Zwart
Gewicht:	4000 g
Breedte:	280 mm
Diepte:	150 mm
Hoogte:	290 mm
Gebruikershandleiding:	Ja
Aan/uitschakelaar:	Ja
Type aansluitplug:	6,3 mm
Connectiviteitstechnologie:	Bedraad
Type stroombron:	AC
Audio-ingang (L, R):	1
Gemiddeld vermogen:	10 W
Volumeregeling:	Draaiknop
Ingang stroom:	Ja
Audio-uitgangskanalen:	- kanalen
AC-ingangsspanning:	230 V
AC-ingangsfrequentie:	50 Hz
Bestandsgrootte luidspreker-stuurprogramma:	6.5 "
Versterkingsregeling:	Ja