Chamberlain NLS2 Handleiding

Chamberlain Intercomsysteem NLS2

Lees hieronder de 📖 handleiding in het Nederlandse voor Chamberlain NLS2 (4 pagina's) in de categorie Intercomsysteem. Deze handleiding was nuttig voor 11 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

HOL D

ACT IVE

TAL K

1 3

2 4

VOLUME

MONITOR

CHANNEL

OF F

Overview

The Intercom has up to a 1000 foot (300 m) range and

allows multiple simultaneous conversations, using a

900 MHz secure digital radio link. The intercoms

form an exclusive network and respond only to other

intercoms in the network.

Carton Inventory

On/Off: To turn intercom ON, press Talk button. To

turn intercom OFF, hold down the Volume DOWN

button for 3 seconds.

Talk Button: To talk, hold down

the Talk button. All intercoms in

the network that are on the same

channel will receive the signal.

Release the Talk button when done

talking and within 10-15 seconds

press and hold the Talk button of a

different intercom to make a secure channel between

the two. Once the channel is made the other intercoms

in the network cannot hear the conversation.

Volume: Pressing the Volume DOWN button will lower

the volume and pressing the Volume UP button will

increase the volume.

Intercom

Models NLS1 & NLS1C (1)

NLS2 & NLS2C (2)

Rubber Pads

Models NLS1 & NLS1C (1)

NLS2 & NLS2C (2)

MONITOR

H DOL

OFF

V MEOLU

TAL K

ACT IVE

Operation & Features

Channel Select Button: Press

the Channel Select button to set

intercom to one of four secure

channels or the paging channel.

The default channel for the intercom

is the paging channel where all four

channel lights are lit. An intercom

on a channel can only hear an

intercom on the same channel or on

the paging channel.

Battery: The AA Alkaline batteries

(not provided) will last up to a year

depending on use. When batteries

are low intercom will emit three

beeps every ten minutes.

A DC Adapter (not provided) can

also be used to power the intercom.

In this case, the channel lights will

remain on.

Conference Mode: Conference Mode allows multiple

intercoms to participate in a conversation compared

to Normal Mode in which only two intercoms

can communicate. All intercoms must be set

to the same channel or the paging channel

to be in Conference Mode. To put intercom

in Conference Mode set Dipswitch #2 to UP

position.

Monitor Mode: Monitor Mode

is used to monitor the noise in a

speciﬁ c room. Place the intercom

in the room that is to be monitored

and press the Monitor button until

a tone is heard. For extended

Monitor usage, consider using a

plug-in transformer. Any other networked intercom can

listen to that room. If a speciﬁ c channel is selected

for Monitor Mode then only other intercoms on that

channel or on the paging channel can listen. Press the

Talk button to exit Monitor Mode. A tone will be heard

indicating Monitor Mode is no longer active.

Voice Activation Mode (VOX): Voice Activation Mode

(VOX) allows a call to be answered without pressing

the Talk button. Once a call is heard on an intercom

which has been set to VOX, a response can be given

by speaking loudly into the intercom. There will be a

slight delay when VOX is ﬁ rst activated by a voice,

but will continue to transmit audio until the

speaking stops. To put intercom into VOX,

place Dipswitch #1 to the UP position. While

in VOX mode, a call may be initiated by

pressing the TALK button.

Volume

Button

Talk

Button

Learn Button

Dipswitch #1

Dipswitch #2

AC Adapter

Models NLS1, NLS2, NLS1C & NLS2C

Wireless Portable Intercom - Extreme Range

V EOLUM

MONIT OR

C LHANNE

HOL D

OFF

ACT IVE

TALK

1 3

2 4

MONITOR

HOLD

OFF

VOLUME

TALK

ACTIVE

OPTIONAL

1 2

Channel

Select Button

Channel

Lights

Active Light

Volume

DOWN

Button

Monitor

Button

Speaker

V EOLUM

MONIT OR

CHANNEL

HOL D

OFF

ACT IVE

TALK

1 3

2 4

V EOLUM

MONIT OR

CHANNEL

HOL D

OFF

ACT IVE

TALK

1 3

2 4

Assemble Intercom

Step 1

Install 4 AA Alkaline batteries (not provided).

Step 2

Adhere rubber pads to bottom. Repeat Steps 1 and 2

for any additional intercoms.

Programming Intercom

The intercom must be programmed to at least one

other intercom to become a network or it can be

programmed into an existing network.

Create New Network

Before programming, clear memory on all intercoms.

Press the Learn button on the new intercom until a

beep is heard. Within 10 seconds put the second

intercom into Learn Mode (refer to the following table).

Each intercom will emit a tone when entering

programming mode. It may take up to 3-1/2 minutes

for a secure network to be established. Repeat for any

additional intercoms.

Add to an Existing Network

Press the Learn button on the new intercom until a

beep is heard. Within 10 seconds put any networked

intercom into Learn Mode (refer to table below).

Each intercom will emit a tone when entering

Programming Mode. It may take up to 3-1/2 minutes

for a secure network to be established. Repeat for any

additional intercoms.

NOTE: Do not program new intercoms to each other

before adding them to the network or they will form

a separate network and the memory will need to be

cleared.

Press and release the Talk button to verify network is

complete.

MONITOR

H DOL

OFF

VOLUME

TAL K

ACT IVE

MONITOR

HOLD

OFF

VOLUME

TAL K

ACT IVE

V EOLUM

MONITOR

C LHANNE

HOLD

OF F

ACT IVE

TALK

1 3

2 4

INTERCOM LEARN MODE

Press the Learn button

until a beep is heard.

HOLD

ACTIVE

TALK

1 3

2 4

VOLUME

MONITOR

CHANNEL

OFF

INTERCOM LEARN MODE

Press the Learn button

until a beep is heard.

HOLD

ACTIVE

TALK

1 3

2 4

VOLUME

MONITOR

CHANNEL

OFF

Troubleshooting

Intercom does not function.

Check batteries in intercom. If using a DC Adapter

ensure that it is plugged in.

Ensure intercom is connected to a network.

See Programming Intercom.

Ensure that intercoms are on the same channel.

See Operation & Features.

Intercom is not getting expected transmission

range.

Keep antenna vertical. Keep intercom away from metal

objects and electrical wiring. Cell phones, cordless

phones, or other radio devices may also limit range.

Intercom beeps every ten minutes.

The battery is low in the intercom. Replace with AA

Alkaline batteries or operate it with DC Adapter

(not provided). A 12 Volt, 300mA DC Adapter may be

used (center positive polarity on the round plug).

Static and feedback is heard in intercom.

The intercoms are too close to each other. A cordless

phone, cell phone, or other radio devices can also cause

static.

The intercom does not connect to another intercom

and a green light is on longer than 3-1/2 minutes.

The intercom is out of range. Place the intercom closer

to the other intercoms in the network, with the antenna

pointing up.

The other intercom in the network has no power.

Replace the batteries.

The intercom has not completed programming.

Clear the intercom's memory and reprogram.

Need to clear intercom’s memory.

Press and hold Learn button, an initial beep will be

heard. Continue to hold until a second beep is heard

(about 6 seconds). Ensure other intercoms are not

activated during this time. Once memory is clear the

intercom can be programmed to a new network.

Intercom is sending audio while no buttons are

pressed.

The sending intercom is set to Monitoring Mode or Voice

Activation Mode and will activate when sound is heard.

It can be taken out of Monitoring Mode by pressing the

Talk button. It can be taken out of Voice Activation Mode

by setting Dipswitch #1 to DOWN position.

See Operation & Features.

Intercom can not be programmed to network.

A network may contain up to 12 intercoms or doorbells.

It may be necessary to clear the network and reprogram

all the intercoms to the network.

See Programming Intercom.

NOTE: Manufacturer is not responsible for any radio or

TV interference caused by unauthorized modiﬁ cations to

this equipment. Changes or modiﬁ cations not expressly

approved by the manufacturer could void the authority

to operate the equipment.

Product specificaties

Merk:	Chamberlain
Categorie:	Intercomsysteem
Model:	NLS2
Kleur van het product:	Black, Grey
Luidspreker:	Ja
Aantal knoppen:	5
Compatibele producten:	NDIS, NTD2, NLS1
DECT connectable:	Ja
Hoeveelheid modules (max):	64 module(s)