CDA KC42 Handleiding
Lees hieronder de š handleiding in het Nederlandse voor CDA KC42 (1 pagina's) in de categorie Wastafel. Deze handleiding was nuttig voor 51 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/1
KC41 and KC42 Fitting Instructions
FAILURE TO FOLLOW THESE INSTRUCTIONS CAN LEAD TO PREMATURE PRODUCT FAILURE.
The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or
installation of this product. Please note that CDA reserve the right to invalidate the guarantee
supplied with this product following incorrect installation or misuse of the appliance or use in a
commercial environment.
Over Mounting
1. Place the paper template provided carefully into the correct position on the worktop.
2. Cut along the over mount line until the central section of the worktop comes out.
3. Use clear silicone to seal the cut that has been made; liberally spread the silicone onto the
area of the worktop directly adjacent to the hole you have made to the width of the sink rim
that it will come into contact with.
4. Repeat step 3 on the under side of the sink rim itself on the surface that will come into
contact with the worktop.
5. Carefully position so that you avoid unnecessary readjustment of the sink at the moment of
contact.
6. Press down firmly and hold in position for at least 5 minutes applying an even pressure.
7. Ensure the sink is fully sealed and the joint is waterproof by squeezing residual silicone out
from along the line of the joint.
8. Do not use the sink for at least 24 hours once fitted.
9. After 24 hours check to ensure the seal is waterproof.
Under Mounting
1. Place the paper template provided carefully into the correct position on the worktop.
2. Cut along the under mount line until the central section of the worktop comes out.
3. Finish the worktop cut out edge to the desired standard.
4. Turn the worktop upside down on a flat, stable surface. Note this will need to be left in
position for 24 hours.
5. Spread clear silicone liberally on the glazed surface on the rim of the sink ensuring no areas
are left uncovered.
6. Spread clear silicone liberally on the underside of the worktop to the corresponding area
where the rim of the sink will be in contact.
7. Press the sink down into the required position firmly for at least 5 minutes applying even
pressure. Position a weight on the sink to keep it in place.
8. Ensure the sink is fully sealed and the joint is waterproof by squeezing residual silicone out
from along the line of the joint.
9. Do not use the sink for at least 24 hours.
10. 3 metal brackets are provided which should be fixed along the front edge and one on each
side; the edge of the bracket overlaps the sink rim and the other edge fixes to the worktop. If
a stone/granite worktop is being used wooden blocks can be used to affix the clips to secure
the sink; these should be fixed with an epoxy-type adhesive (follow manufacturersā
instructions for Epoxy adhesive use).
Product specificaties
| Merk: | CDA |
| Categorie: | Wastafel |
| Model: | KC42 |
Heb je hulp nodig?
Als je hulp nodig hebt met CDA KC42 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Wastafel CDA
20 Juni 2023
19 Juni 2023
18 Juni 2023
13 Juni 2023
12 Juni 2023
12 Juni 2023
9 Juni 2023
7 Juni 2023
6 Juni 2023
6 Juni 2023
Handleiding Wastafel
- Wastafel IKEA
- Wastafel Bartscher
- Wastafel Franke
- Wastafel Lynx
- Wastafel Miomare
- Wastafel Rangemaster
- Wastafel Smeg
- Wastafel Blanco
- Wastafel Kernau
- Wastafel Cata
- Wastafel Elkay
- Wastafel Gustavsberg
- Wastafel Coyote
- Wastafel ZLine
- Wastafel Differnz
- Wastafel Enza
- Wastafel Alfi
- Wastafel ARC
- Wastafel Vigo
- Wastafel Dxv
- Wastafel Signature Hardware
- Wastafel Whitehaus
- Wastafel Thompson Traders
- Wastafel Rohl
Nieuwste handleidingen voor Wastafel
11 December 2024
11 December 2024
11 December 2024
11 December 2024
3 December 2024
15 November 2024
15 November 2024
15 November 2024
15 November 2024
15 November 2024