BDI Revo 9981 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor BDI Revo 9981 (3 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 54 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/3
1
Your Revo Home Theater Furniture is engineered for easy
assembly. Carefully follow this procedure to prevent any damage.
Placement and Maintenance
Revo Home Theater Furniture is designed for indoor use on level
floors. Clean glass with glass cleaner, and steel parts and wood
veneer with a moist cloth.
Step 1
Unpack and identify the parts listed above. The assembly
workspace should be a non-marring surface such as carpet. For
missing hardware pieces, please contact BDI Customer Service
at customerservice@bdiusa.com. For all other concerns, please
contact your BDI Retailer.
Step 2
Revo 9981 features a swiveling base. Note that Swivel-Lock Pins
(F) are factory-installed at Position 1 enabling the stand to swivel
15-degrees to left and 15-degrees to right.
To lock the stand in a fixed position, use provided Allen Wrench
(E) Swivel-Lock Pins (F) Position 1 (factory to remove both from
position) Position 2. and re-install them at
Revo
Component List
Designed by Louis Lara.
These distinctive product configurations are protected by US and international
patents, trade dress, and/or copyright laws.
BDI are trademarks of Becker Designed, Inc. All Rights reserved. ©2009, BDI
9981REV092409v8
a s s e m b l y i n s t r u c t i o n s
bdiusa bdiusa.com customerservice@ .com
9981
D - Phillips Screwdriver
x 1
E - Allen Wrench x 1
C - Retention Clip x 8
Pre-installed
A - Glass Shelf x 2
B - Shelf Pin x 8
Pre-installed
F - Swivel-Lock Pin x 2
Pre-installed
Front
Position 2
Position 1
F
NOTE: Choosing not to use the
Swivel-Lock Pins (F) will enable
360-degrees of rotation.
2assembly instructions
bdiusa bdiusa.com customerservice@ .com
Step 2
Confirm that are pre-installed.Shelf Pins (B)
In order to adjust height, one must remove
the glass retention clip (secured by the
shelf pin) that holds the glass shelves in
place.
Loosen the 4 1. Shelf Pins (B)
Phillips Screwdriver 1 turn with
(D).
Remove 2. Retention Clips (C) ( x 4 )
Unscrew 3. Shelf Pins (B) completely
Reposition the 4. Shelf Pins (B) at
desired height
Secure Glass Shelves
To secure the shelves on your Revo unit, it is
necessary to use the Retention Clip (C), which
is secured by the Shelf Pin (B).
Install 5. Glass Shelves (A x 2)
Install 6. Retention Clips (C) as shown in
Pin Assembly Diagram”
Secure by tightening the7. Shelf Pin (B)
Phillips Screwdriver (D).with
A x 2
Retention clip (C)
Shelf pin (B)
Detail of Shelf Pin (B) and
Retention Clip (C)
1
1
44
1 : Retention clip (C)
2 : Glass Shelf (A)
3 : Shelf Pin (B)
4 : Cabinet wall
Pin Assembly Diagram
3assembly instructions
bdiusa bdiusa.com customerservice@ .com
1.
2.
3.
3.
1.
2.*
2.*
2. 2.
3.
1.
1.
Figure 2Figure 1
Step 4
Install Back Panel.
The back panel comes pre-installed. Follow illustrations below for
installation and removal.
Step 5
Adjust Door Hinges (if needed)
If the cabinet’s doors appear out of alignment, this condition can be corrected with minor adjustment
to the European hinges on each door.
Because these hinges are infinitely adjustable, adjusting one hinge element can sometimes cause the
need for adjustments to other elements. But with a few adjustments, you can modify the orientation of
the cabinet doors to make sure that they hang perfectly within your cabinet.
Use a Phillips screwdriver to adjust Revo’s door hinges:
By adjusting • Screw 1, the door will move LEFT or RIGHT within the frame. Make minor
adjustments at both top and bottom hinges for best results.
By adjusting • Screw(s) 2, the door will move UP or DOWN within the frame (the top and bottom
hinges must be adjusted the same degree).
NOTE: Screws 2If your hinges have a Slotted Mounting Plate (as shown in Figure 2): Loosen
one complete turn, raise or lower door, then hold in position while tightening (on both Screws 2
hinges).
By adjusting • Screw 3 the entire door will move IN or OUT, opening or closing the gap between the
door frame and cabinet. (This screw rarely needs adjustment.)
3.


Product specificaties

Merk: BDI
Categorie: Niet gecategoriseerd
Model: Revo 9981

Heb je hulp nodig?

Als je hulp nodig hebt met BDI Revo 9981 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd BDI

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd