Audiovox PRO-9056TW Pursuit Series Handleiding

Audiovox Beveiliging PRO-9056TW Pursuit Series

Lees hieronder de 📖 handleiding in het Nederlandse voor Audiovox PRO-9056TW Pursuit Series (2 pagina's) in de categorie Beveiliging. Deze handleiding was nuttig voor 40 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

128-8856

1 of 2

Single Channel Remote

Car Starter

Model PRO-9056TW

Owner’s Manual

FEATURES :

 1 Programmable RF Transmitters, 1 Programmable RF Transceiver

 Single Channel Receiver (capable of accepting 4 transmitters)

 External Superheterodyne Receiver Antenna w/PushButton Switch &

Orange LED

 On-Board Start Relay

 On-Board Accessory Relay

 On-Board Ignition 1 Relay

 On-Board Ignition 2 Relay

 Ignition 2 Relay Selectable On or Off During Cranking

 On-Board Parking Light Relay

 Ignition 3 / Shock By-Pass / GM VAT Output (relay required)

 Tach Signal Learning Circuit

 Two ( + ) and Two ( - ) Safety Shutdown Circuits

 Alarm By-Pass Output

 Accessory Outputs

(Pulse Before & After Start, During Crank & After Shut Down)

 Selectable Steady or Flashing Parking Lights for Run Indication

 Selectable 5, 10, 15, 20 Minute Run Time

Optional Door Unlock Feature For Vehicles Equipped With Power Doors

(Only operational while running under control of the remote start unit.)

128-8856

2 of 2

REMOTE STARTING THE VEHICLE

This will not start the vehicle if any one of the following situations exists:

The vehicle's hood lid is opened.

The gear shift selector is not in Park.

The brake pedal is depressed.

The safety control switch is in the Off position.

1) To start the vehicle, press and release the transmitter button two times within

2 seconds. The vehicle will start and remain running for the

pre-programmed time up to a 60 minute run cycle. As a

visual indication, the parking lights will flash or remain on

depending on the setting by your installation center. Addi-

tionally if the two way transceiver shown on the right is used,

the transceiver will play a melody when the vehicle is started,

and the Orange LED surrounding the transceiver button will

flash every ten seconds while the vehicle is running.

2) When you arrive at the vehicle, turn the ignition key to the

ON position (not the spring loaded start position), then step

on the brake pedal to disengage the remote starter. The

vehicle will continue to run, but now on its own power.

NOTE: The engine will stop running before the pre-programmed

run cycle has expired if you perform any one of the following

functions:

-Press the button on the keychain transmitter two times within 2 seconds

-Depress the brake pedal

-Open the vehicle's hood

-Move the safety control switch to the Off position.

PUSH-BUTTON LED RECEIVER VALET/OVERRIDE/SAFETY CONTROL SWITCH

The Push-Button LED switch located in the receiver allows you to temporarily disable the remote

starting function of the system. This recommended whenever the vehicle is being serviced. To place

the system in the service mode:

1) With the system disarmed/unlocked, and the ignition switch off, Press and Hold the Push-Button

switch found on the windshield receiver, in.

2) Turn the ignition switch on, off, on, off, on, off.

3) The Orange LED begins to flash two short flashes followed by one long flash and continues this

pattern until the unit is returned to the normal mode of operation.

The above action puts the unit into the Remote Start Override/Service mode and will not start from

the RF transmittor or any other input, Posse or otherwise.

To Exit Remote Start Override Mode

1) With the system disarmed, Press and Hold the Push-Button switch found on the windshield

receiver, in.

2) Turn the ignition switch on, off, on, off, on, off.

3) The LED turns off indicating that the Remote Start unit is fully functional once again.

UNLOCKING THE VEHICLE:

If you have electric door lock, and the Optional Unlock feature was added, with the vehicle running

under command of the remote start unit, press and hold the transmitter button for 3 seconds until

the doors unlock.

TELEMATIC UPGRADE:

This system has the ability to have a telematic upgrade module connected to it. This is an upgrade that

can give you control of certain functions of your vehicle from a Telephone, or in some cases a

computer interface. Please check with your installation center for most recent Telematic Upgrades. If

you had a Telematic Upgrade installed, the manual supplied with the upgrade unit will provide a

operator's manual advising of the features of the system and means available to control these

features of your vehicle.

.FUNCTION SETTING CHART To be completed by installer

Run Time 5 Min 10 Min 15 Min 20 Min 

Lights Pulse Steady 

Product specificaties

Merk:	Audiovox
Categorie:	Beveiliging
Model:	PRO-9056TW Pursuit Series

Heb je hulp nodig?

Als je hulp nodig hebt met Audiovox PRO-9056TW Pursuit Series stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Beveiliging Audiovox

Audiovox AS9233ST Handleiding

8 Juli 2023

Audiovox Prestige Platinum APS 686T Handleiding

8 Juli 2023

Audiovox APS-45 Handleiding

8 Juli 2023

Audiovox PRO-9056TW Pursuit Series Handleiding

8 Juli 2023

Audiovox APS 675 Prestige Platinum Handleiding

8 Juli 2023

Handleiding Beveiliging

Nieuwste handleidingen voor Beveiliging

Geemarc SOS-PRO 295 Handleiding

6 Maart 2024

Technaxx TX-106 Handleiding

4 Februari 2024

One2track Safety Angel Handleiding

16 Oktober 2023

Sygonix SY-3851632 Handleiding

16 Oktober 2023

Sygonix 1326052 Handleiding

16 Oktober 2023

Sygonix 43588A WLAN Camera Handleiding

16 Oktober 2023

Sygonix 43176S LAN Camera Handleiding

16 Oktober 2023

Sygonix SY-3181234 Handleiding

16 Oktober 2023

Sygonix Touch IP65 Handleiding

16 Oktober 2023

Sygonix 1882082 Handleiding

16 Oktober 2023