Audio-Technica ATW-49CB Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Audio-Technica ATW-49CB (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 47 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
ACTIVE ANTENNA COMBINER KIT
The Audio-Technica ATW-49CB Active Antenna Combiner Kit includes two
dual-input, one-output Active Antenna Combiners designed for use with
Audio-Technica 4000 and 5000 Series UHF wireless receivers and ATW-A49
LPDA antennas.* Each Active Antenna Combiner is a broadband device
(frequency range from 440 to 900 MHz) that combines two incoming RF
signals into one outgoing RF signal. One set of Active Antenna Combiners
enables two sets of antennas to feed one wireless receiver or distribution
system. To compensate for RF signal loss associated with combining signals,
the Active Antenna Combiner provides unity gain. (Note that without the
use of an antenna preamplier, long antenna-cable length may deteriorate
signal.)
Each kit includes: two Active Antenna Combiners and two 45mm BNC-to-
BNC RG 58 coaxial antenna cables.
NOTE: The ATW-49CB Antenna Combiner requires +12V DC power from
any Audio-Technica 4000 or 5000 Series receiver or +5 to +14V DC from any
wireless receiver or antenna distribution system that offers antenna power.
A light on each Active Antenna Combiner indicates that power has been
correctly applied.
* The ATW-49CB Active Antenna Combiner Kit is also suitable for use with
other receivers that are in its specied band, use BNC antenna connectors,
and provide antenna terminal voltage; it may also be used with a variety of
other antennas from Audio-Technica and other manufacturers.
HOW TO INSTALL THE ATW-49CB ACTIVE ANTENNA COMBINERS
1. Connect one BNC-to-BNC RG 58 coaxial antenna cable (two supplied)
to the OUT connector on one Active Antenna Combiner (two supplied).
Connect the other end of this cable to the ANTENNA A input on either a
receiver or distribution amplier, as shown in Figure 1.
2. Repeat step 1 for the ANTENNA B input, using the second Active Antenna
Combiner.
3. Use coaxial antenna cables (not included) to connect the IN connectors
on each Active Antenna Combiner to a UHF antenna, as shown in Figure 1.
4. NOTE: ATW-A49 antennas do not require power. If you are using
ATW-A49 antennas, skip Step 4. If you have an antenna system that
requires power (such as an antenna preamp or booster) you must open
the ATW-49CB Active Antenna Combiner assembly and activate a switch
on the circuit board. (This enables the combiner to pass power through to
the antenna.) Current consumption of the preamp or booster should not
exceed 100mA.
The unit is shipped with the switch in the off” position. To ip the switch
to the “on” position, first be certain the combiner is not attached to
any power source. Next, use a Phillips screwdriver to remove the two
screws on the Active Antenna Combiners access panel; remove the
access panel; use a tweezers to flip the switch into the “on” position.
Finally, replace the access panel and securely tighten the two screws. (See
Figure 2.)
FORM No. ATGC-L0024-06-E
Machida Tokyo Japan
SPECIFICATIONS
DESCRIPTION 2-input Active Combiner
BANDWIDTH 440 MHz to 900 MHz
VSWR < 1.7:1 (within specied bandwidth)
GAIN 0 dB typical (within specied bandwidth)
IMPEDANCE 50 ohms, typical
(within specied bandwidth)
TERMINATION TYPE 3-BNC Female
WEIGHT 51 g
DIMENSIONS 61.0 mm W x
47.0 mm L x
23.0 mm H
DC INPUT 5-14V DC
CURRENT 30 mA @ 12V DC
FINISH ON ENCLOSURE Chemical lm per MIL C 5541
MATERIAL 6063T52 extruded aluminum (sides)
5052-H32 aluminum (top and bottom)
PASS-THROUGH CURRENT 100 mA (maximum to both inputs
combined)
Figure 1
OUT
Receiver or Distribution
Amplier
IN IN IN IN
OUT
ON
OFF
Figure 2
FORM No. ATGC-L0024-06-C
Machida Tokyo Japan
有源天线汇合器套件
ATW-49CB是一套两路天线输入、一路输出的有源天线汇合器,
可配合鐵三角4000 5000及 系列无线话筒及ATW-A49极子天线使
*每个汇合器为宽频率元件 (频率范围由440900MHz),可
两个射频输入信号汇合为一个射频输出信号,而一套汇合器可配
套一台接收机或一台天线分配器使用。天线汇合器内置有源放大
器,以补尝在汇合处理时的信号损失。 汇合器并没有天线前置放(
大器,过长的天线连接线会导致信号减弱)
套件内包括:两个有源天线汇合器,两条 长 接头45mm BNC-BNC
RG58同轴天线连接线。
注:ATW-49CB 4000 5000线合 器需 要 列无线
收机提供的 直流或其他无线接收机及天线分配器的 至+12V +5
+12V直流幻象供电。汇
* ATW-49CB BNC天线汇合器可配套于其他在频率范围内,以
头及的接使外,鐵三
角或其他型号的天线使用。
ATW-49CB线
1. 使用一条BNC-BNC接头连接线连接天线
或分的 组线输A
2. 使重复第1步骤,用另一条连接线,连接另一线
出端到 组天线输入。B
3. 使用天线的轴连接线连接个天线
线。 图( 1)
4. 注:ATW-A49 ATW-A49天线不需使用幻象供电,如使用 天
线,可跳过此说明。如使用的天线系统需要供电 内置前(
大 器 或增 益 , 需 开启 汇合 器电 路 板内 的导 通 电 流 开)
使天线上,而所提供的总
电流不应超过100mA
 汇合器的导通电流开关,预设为关闭 位置,需使用"OFF"
十字螺丝刀把底盖打开,再以小型一字螺丝刀把开关推至
后再。 图"ON" ( 2)
(前请)
技术指标
工作情况 2路有源输入汇合器
频宽 440 MHz - 900 MHz
电压驻波比 < 1.7 :1 (于指定频宽)
增益 0dB 典型 (于指定频宽)
阻抗 50 欧姆,典型 (于指定频宽)
端子 3BNC母头
重量 51
外形尺寸 61.0 mm - 宽 x
47.0 mm - 长 x
23.0 mm -
供电输入 5-14V 直流
消耗电流 30mA 12V 直流
封装涂层 MIL C 5541 化工薄膜
物料 6063T52 压铸铝合金 (边框)
5052-H32 铝合金 (底及顶)
导通电流 100mA (两输入端最大值)
1
接收机或天线分配放大器
ON
OFF
2
输出 输出
输入输入输入输入


Product specificaties

Merk: Audio-Technica
Categorie: Niet gecategoriseerd
Model: ATW-49CB

Heb je hulp nodig?

Als je hulp nodig hebt met Audio-Technica ATW-49CB stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Audio-Technica

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd