Atdec VF-AT-D Handleiding

Atdec Flat panel steun VF-AT-D

Lees hieronder de 📖 handleiding in het Nederlandse voor Atdec VF-AT-D (2 pagina's) in de categorie Flat panel steun. Deze handleiding was nuttig voor 45 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

A Component Checklist - Check you have received all parts against the component checklist prior to installing

Bolt Through

Installation Instructions

Steel washer

Bolt Through Base

M8 Desk Clamp Screw

(found in the Desk

Clamp Box)

5mm Allen

Key

9mm (³/8”) Hole

Drill a 9mm (³/

8”) hole in the

work surface at the desired

position and assemble as

shown below.

NOTE:

Ensure the slot in the Pole Assembly faces away

from the user.

It is recommended that the Pole Assembly be

mounted towards the rear edge of the work surface

IMPORTANT:

The “User Operating Card”

must be left

with Visidec Focus Articulated

Arm Double once installed

Desk Clamp

Pole Assembly

B1 B2

mottoB

Slot

NOTE: When using the Desk Clamp mounting option,

the displays can only be used in side by side

configuration as shown. Failure to do so may result in

serious damage to product and displays.

Tighten Firmly

Double Arm

Assembly

Pole Assembly

User Operating Card

(see note at top of page)

Desk Clamp Box

5mm Allen

Key

Desk Clamp Bracket M8 Desk

Clamp Screw

Bits Box

Primary Arm

Cable Cover (x2)

Secondary Arm

Cable Cover (x2) Bolt Through

Base Steel

Washer

M8x30mm

Screw

Pole Top

Cap Cable Clip (x2)

Display Mounting

Screws

M4x16mm

(x8)

M4x12mm

(x8)

M4x10mm

(x8)

Cable

Balls (x2)

Work Surface

Pole

Assembly

Step 3: Adjust the height of the Pressure Plate to suit the

Work Surface and tighten ﬁrmly in the desired location.

5mm Allen Key

Tighten Firmly

Step 1: Attach the Desk Clamp Bracket to the bottom

of the Pole Assembly using the M8x30mm Screw.

Tighten ﬁrmly using the 5mm Allen Key.

Ensure the Visidec logo is facing the front as shown.

M8x30mm

Screw

mottoB

Step 2: Install the M8 Desk Clamp

Screw and Pressure Plate as shown.

Desk

Clamp

Bracket

5mm

Allen Key

Bolt Thru

Base

Pole

Assembly

Pressure

Plate

M8 Desk

Clamp Screw

5mm

Allen Key

NOTE: It is recommended that the Pole

Assembly be clamped to the rear or side

edge of the work surface

Suits 12mm (½”)

to 38mm (1½”)

thick work

surfaces

ADJUSTMENT RANGE

Pressure Plate

Tighten

Firmly

D Mount the Display

For Displays with 75mm x 75mm

(3” x 3”) mounting hole patterns

M4 Display Mounting Screws

Step 1: Connect cables

Step 2: Insert

Secondary Arm

Cable Cover*

Step 3: Insert

Primary Arm

Cable Cover*

NOTE: Leave enough slack in the

cables to allow for movement

E Cable Management - Make sure arms are fully extended before connecting cables

NOTE: If Visidec Focus

Articulated Arm Double is

to be used in a multi-user

evironment, do not install

the Cable Balls and only

use the Cable Clips.

C Assemble the Double Arm Assembly onto the Pole Assembly

Step 1:

Unlock the

handgrip

Step 2:

Lift the handgrip to

the top of the pole

so that the Handgrip

Tab protrudes

Step 3:

Slip the Double Arm Assembly

over the Handgrip Tab and

then onto the Pole

Step 4:

Slide the Double

Arm Assembly

and the Handgrip

down the Pole.

Step 5:

Lock the

Handgrip

Step 6:

Insert the Pole

Top Cap into

the Pole

Step 7:

Insert the 5mm Allen

Key into the slot in

the Pole Top Cap

Pole Top Cap

Handgrip Tab

Handgrip

For Displays with 100mm x 100mm

(4” x 4”) mounting hole patterns

M4 Display Mounting Screws

F Leave the “User Operating Card” with Visidec Focus Articulated Arm Double

Leave the “User Operating Card” secured to the base of Visidec Focus Articulated Arm Double with the “atdec”

logo facing upwards.

*To insert Cable Covers:

Insert tabs

Double Arm

Assembly

Step 4: Insert cables into

slot, using cable balls to hold

them in place (single user only)

- see note. Cable

Balls (x2)

Step 5: Attach remaining

cables that do not ﬁt into the

slot with the two supplied

cable clips.

Push in...

...and then up

No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.

Due to continuing product development, the manufacturer reserves the right to alter speciﬁcations without notice. Published: 13.02.08 ©

Product specificaties

Merk:	Atdec
Categorie:	Flat panel steun
Model:	VF-AT-D
Kleur van het product:	Zilver
Montagewijze:	Bureau
Maximale gewichtscapaciteit:	8 kg
Gewicht (imperiaal):	17.5 lbs
Draaihoek:	240 °
Pan bereik:	0 - 180 °
Bereik kantelhoek:	-70 - 70 °
Bevestigingsstandaard:	VESA 75mm x 75mm / 100mm x 100mm
Lift:	31.5 cm