Atdec AWMS-DW Handleiding
Atdec
Flat panel steun
AWMS-DW
Lees hieronder de đ handleiding in het Nederlandse voor Atdec AWMS-DW (4 pagina's) in de categorie Flat panel steun. Deze handleiding was nuttig voor 2 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/4
AWMS-DW Page 1 of 4
Installation Guide
AWMS-DW
Dynamic Arm Wall Mount
COMPONENT CHECKLIST
A
Single Wall
Bracket
(x1)
G
Screw
M4x25mm
(x4)
H
Screw
M4x16mm
(x4)
I
Screw
M4x12mm
(x4)
F
Spacer
(x4)
J
Security
Screw
(x1)
E
Washer
(x2)
D
Screw
M8x70mm
(x2)
K
4mm
Hex Key
(x1)
L
6mm
Hex Key
(x1)
C
VESA
Head
(x1)
B
Dynamic
Monitor Arm
(x1)
REQUIRED TOOLS
⢠Phillips head screwdriver
⢠Power drill
⢠Suitable drill bit
⢠Driver bit for selected
wall fasteners
⢠Stud î´nder
⢠Spirit level
WEIGHT RANGE
Flat Monitor
0 - 9kg (0 - 20lb)
Curved Monitor
0 - 6kg (0 - 13.5lbs)
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! Do not remove or throw away the plastic sleeve on wall bracket and arm links.
! The manufacturer accepts no responsibility for incorrect installation.
! Failure to install this product correctly may cause serious injury/death during or following installation.
! This product is not suitable for outdoor use.
! Do not use this product for mobile applications.
! This product should only be installed by professional installers of good mechanical aptitude, who have experience with
building construction, and fully understand these instructions and the consequences of incorrect installation.
! Supplied wall fasteners are for timber stud wall constructions . For other wall constructions, such as masonry, alternative only
suitable wall fasteners should be sourced by the installer.
! To safely achieve the full capacity of this product, wall fasteners must have a pull-out (tension) force rating of at least 100kg
(1000N) per fastener. This rating must include a safety factor.
! Professional installer to ensure adequate structural capacity of wall (including appropriate safety factor) to support total
weight of all equipment being mounted.
! Drilling into electrical wires can cause death - use appropriate equipment and caution when drilling holes in walls to avoid
electrical cables, water pipes and gas pipes. Do not drill into structures unless you have established itâs safe to do so.
! Curved monitors, deep devices (such as all-in-one PCs), VESA mounted accessories (such as mini PC brackets and mounts),
and offset VESA locations exert additional leverage that can exceed the capacity of the mount even though the monitor
weight may be within the stated range. Please contact Atdec if you would like further information.
AWMS-DW Page 2 of 4
4.1 Check VESA mounting
compatibility.
3.1 Push arm onto the wall bracket
shaft. Ensure grub screw is retracted
before doing so.
4. Attach VESA head to monitor
1. Mount the Wall Bracket to the Wall
x2
Using the
Single Wall
Bracket as
a template,
mark the
two î˛xing
hole positions
for drilling.
NOTE: On a timber
stud wall, use a good
quality stud î˛nder to
position mounting
fasteners in the
centre of studs.
NOTE: Wall bracket
must be level. Verify
using a quality spirit
level tool positioned
along the side edge
of the wall bracket.
NOTE:
⢠Alternative wall constructions, such as masonry,
will require different fasteners than what is
supplied with the product.
⢠Selection and sourcing of alternative wall mounting
fasteners is the responsibility of the installer. See
âImportant Informationâ above for more details.
NOTE: Thickness of sheeting and cladding
over the timber stud, including plaster board,
should not exceed 15mm ( â).â
70mm (2 3
/
4â)
Stud
(5
/
32â)
4mm
Timber Stud
2. (Optional) Set arm rotation to 360°
Note rotation is set to 180 by default. This will protect the wall by preventing the arm swinging into it.°
2.1 Remove plastic
sleeve from wall
bracket
2.2 Remove
rotation ring.
2.3 Place rotation ring in
desired position and replace
plastic sleeve.
3. Fit arm to Single Wall Bracket
3.2 Ensure arm is fully
pushed onto bracket
3.3 Tighten the set screw with
4mm Hex Key to secure the arm
in place.
NOTE: Check
the joint
rotation is
smooth after
tightening.
NOTE:
Ensure
plastic
sleeve is on
shaft before
î˛tting arm.
4.2 Attach VESA head onto monitor with
provided screws.
NOTE: Spacers may be required for curved,
recessed or uneven monitor surfaces.
100mm
75mm
100mm
75mm
NOTE: For other sizes, use a suitable
adaptor plate (sold separately).
180°
Default
Position
OR
360°
Flipped
Position
Flush
Too long Too short
Spacer
5mm 12mm
NOTE: Be sure to use a screw
length that suits the monitor.
AWMS-DW Page 3 of 4
5. Mount monitor
5.1 Insert VESA head into the
monitor arm.
5.3 Push the lever down to
secure it to the arm assembly.
5.2 Ensure that the VESA head sits
îłush within the monitor arm. There
should be gap.no
Monitor arm Gap No gap
6. Adjust tilt tension & Install security screw
Loosen
Tighten
6.1 Use the provided Hex Key to adjust the tilt tension until
the monitor holds in a vertical position at the end of the arm.
NOTE: Support
monitor while adjusting
6.2 (OPTIONAL) To install the optional security
screw tilt the head upwards.
7. Adjust arm tension
Heavier
Monitor
Lighter
Monitor
7.1 To accurately set the tension of the arm,
position the monitor at 90 degrees
7.2 Use the allen key to adjust the arm tension to the weight
of the monitor. Follow steps to set the tension.7.3 to 7.5
90°
7.3 If the monitor sags or falls down,
increase the arm tension by rotating
the screw clockwise.
7.5 If the monitor îłoats or hovers
in all positions the arm tension
is balanced and does not require
further adjustment.
7.4 If the monitor springs upwards
from the bottom position, decrease
the arm tension by rotating the
screw anti-clockwise.
Monitor Falls
(from top)
Increase Tension
Monitor âFloatsâ
(all positions)
Balanced
Monitor Springs
(from bottom)
Reduce Tension
Product specificaties
| Merk: | Atdec |
| Categorie: | Flat panel steun |
| Model: | AWMS-DW |
Heb je hulp nodig?
Als je hulp nodig hebt met Atdec AWMS-DW stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Flat panel steun Atdec
30 Januari 2025
30 Januari 2025
30 Januari 2025
7 December 2024
7 December 2024
7 December 2024
7 December 2024
7 December 2024
7 December 2024
7 December 2024
Handleiding Flat panel steun
- Flat panel steun HP
- Flat panel steun Samsung
- Flat panel steun Pioneer
- Flat panel steun Abus
- Flat panel steun Acco
- Flat panel steun Akai
- Flat panel steun Apart
- Flat panel steun Atlantic
- Flat panel steun B-tech
- Flat panel steun BenQ
- Flat panel steun Blaupunkt
- Flat panel steun BlueBuilt
- Flat panel steun Dell
- Flat panel steun Digitus
- Flat panel steun Ematic
- Flat panel steun Ewent
- Flat panel steun Fellowes
- Flat panel steun Gembird
- Flat panel steun GPX
- Flat panel steun Hitachi
- Flat panel steun HQ
- Flat panel steun Icy Box
- Flat panel steun Iiyama
- Flat panel steun InFocus
- Flat panel steun Insignia
- Flat panel steun Kensington
- Flat panel steun Kogan
- Flat panel steun Konig
- Flat panel steun Luxor
- Flat panel steun Manhattan
- Flat panel steun Marantz
- Flat panel steun Nabo
- Flat panel steun Nec
- Flat panel steun Newstar
- Flat panel steun Peerless
- Flat panel steun Premier
- Flat panel steun Pyle
- Flat panel steun Reflecta
- Flat panel steun Speaka
- Flat panel steun Ultimate
- Flat panel steun Vogels
- Flat panel steun One For All
- Flat panel steun 3M
- Flat panel steun Monoprice
- Flat panel steun Schwaiger
- Flat panel steun Steren
- Flat panel steun Bell'O
- Flat panel steun SilverStone
- Flat panel steun Techly
- Flat panel steun SIIG
- Flat panel steun Sven
- Flat panel steun Tripp Lite
- Flat panel steun Sanus
- Flat panel steun Vision
- Flat panel steun LC-Power
- Flat panel steun Kondator
- Flat panel steun Barkan
- Flat panel steun Bretford
- Flat panel steun Chief
- Flat panel steun Gabor
- Flat panel steun Planar
- Flat panel steun SunBriteTV
- Flat panel steun Cabstone
- Flat panel steun Da-Lite
- Flat panel steun Peerless-AV
- Flat panel steun Valueline
- Flat panel steun BakkerElkhuizen
- Flat panel steun CTA Digital
- Flat panel steun Wentronic
- Flat panel steun SMS Smart Media Solutions
- Flat panel steun Proaim
- Flat panel steun AMX
- Flat panel steun Ergotron
- Flat panel steun Equip
- Flat panel steun Konig & Meyer
- Flat panel steun StarTech.com
- Flat panel steun Anthro
- Flat panel steun Crimson
- Flat panel steun Panduit
- Flat panel steun Premier Mounts
- Flat panel steun Elite Screens
- Flat panel steun Kanto
- Flat panel steun V7
- Flat panel steun SmartMetals
- Flat panel steun Unicol
- Flat panel steun Alogic
- Flat panel steun Zaor
- Flat panel steun Dataflex
- Flat panel steun Multibrackets
- Flat panel steun Mount-It!
- Flat panel steun Rocstor
- Flat panel steun Amer
- Flat panel steun Avteq
- Flat panel steun Walker Edison
- Flat panel steun My Wall
- Flat panel steun LTN Technologies
- Flat panel steun Heckler
- Flat panel steun Helder
- Flat panel steun NeoMounts
- Flat panel steun DQ
- Flat panel steun Adicam
Nieuwste handleidingen voor Flat panel steun
30 Januari 2025
30 Januari 2025
30 Januari 2025
30 Januari 2025
29 Januari 2025
29 Januari 2025
29 Januari 2025
28 Januari 2025
28 Januari 2025
28 Januari 2025