Atdec TH-PPA-2448 Handleiding

Atdec Flat panel steun TH-PPA-2448

Lees hieronder de 📖 handleiding in het Nederlandse voor Atdec TH-PPA-2448 (5 pagina's) in de categorie Flat panel steun. Deze handleiding was nuttig voor 37 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/5

M2.5x15mm w/ Washer

M3x15/20mm w/ Washer

TH-PF

Component Checklist

Pro AV Projector Ceiling Mount

Square Nut (x4)

Leg (x4)

Coach Bolt (x4)

Nylon

Anchor (x4)

HARDWARE Projector Mounting Screws (x4 each)

M4x15/20/25mm

M5x15/20/25mm

M6x15/20/25mm

Tools Required:

• Power Drill

• 4mm(0.15”) Drill Bit

• 9mm(0.35”) Masonry Drill Bit

• Phillips Head Screwdriver

• 13mm (0.5”) Socket Wrench/ Shifter

! IMPORTANT - Install Telehook Projector Ceiling Mount as per installation instruction.

! This product supports a maximum load of 25kg (55lbs.).

! The manufacturer accepts no responsibility for incorrect installation.

IMPORTANT INFORMATION:

Step 1. Check Components

Check you have received against the component checklist and hardware above.

M6 Washer (x4)

Mount

Step 2. Cable Management

Step 4. Ceiling Mount

Base Plate

10mm Spacer

(x4 each)

M5x10mm Socket

Head Screw (x4)

M5x10mm

Security Screw

3mm Security

Allen Key

Security Cap (x4)

The TH-PF can be mounted flush to a ceiling (Step 4) or to a pole (Step 5).

Before mounting your TH-PF, give consideration to your cable route. The

TH-PF has provision for cable management as shown below.

Step 3. Choosing Orientation

Ensure the Mount is attached with the Projector Marks pointing in the same

direction that the projector will be facing.

Projector Mark

IMPORTANT! Any structural elements must be capable of supporting the combined weight of

all the equipment and devices being mounted. If in doubt, consult a structural engineer.

Timber Stud Masonry

Coach Bolt

M6 Washer

Mount

TIP: Use Mount as a drilling template.

Coach Bolt

M6 Washer

Mount

Ø9mm x 40mm deep

Drilled Hole

Ø4mm x 35mm deep

Drilled Hole

Installation Instructions

Step 5. Pole Mount

Note: The TH-PF is compatible with 1.5NPT thread.

A range of Pole Accessories are available from Atdec.

1. Install Pole Accessory.

2. Thread mount fully into the end of the Pole.

3. Set the orientation by unwinding the mount. Do

not unwind the mount more than one full turn.

4. Lock the mount in place by tightening the two

security set screws in place using the supplied

security allen key.

Pole Accessory

(Purchased separately

or as part of a kit

from Atdec)

2 MOUNT

4 TIGHTEN

Step 7. Attach the Legs to the Projector

Leg

Spacer

(optional)

Projector

Projector Mounting

Screw

Note: Washers must be used in conjunction with M2.5 and M3 projector mounting screws.

FOUR FIXING POINTS THREE FIXING POINTS

Step 6. Mounting Projector

Depending on the size of your projector, the

TH-PF has several mounting options available.

Smaller Projectors can be mounted directly to

the Base Plate.

For all other projectors, use the supplied legs.

Projector Mounting

Screw

Base Plate

Projector

Spacer (optional)

Projector Mounting

Screw

Leg

Spacer (optional)

Projector

Washer (optional)

Step 8. Height Adjustment

Step 9. Insert Security Caps Step 10. Insert Square Nuts

Security Cap

Insert Security Cap and tighten using the supplied 3mm Security Allen Key.

INSERT

Square Nut

Insert one Square Nut to each leg.

Note: if a difference in height of over 7mm is present use the

spacers provided

+ HEIGHT

- HEIGHT

Rotate the dial of the Leg counter-clockwise to increase height and

clockwise to decrease height.

If the surface of the projector is uneven the height of the legs can

be adjusted to allow the legs to level with each other by turning

the dial on the leg.

7mm Max.

Studs

1. The four studs on the Base Plate should point along the axis

of the projector.

2. Position the Base Plate centrally towards the heaviest part of

the projector so that the weight of the projector is centred and

balanced after mounting.

Step 11. Base Plate Orientation Step 12. Attach Base Plate

Use the supplied 3mm Security Allen Key to tighten the four screws.

Base Plate

M5x10mm Socket

Head Screw

Square Nut

(inside the Leg)

Product specificaties

Merk:	Atdec
Categorie:	Flat panel steun
Model:	TH-PPA-2448
Kleur van het product:	Wit
Montagewijze:	Plafond
Maximale gewichtscapaciteit:	454 kg
Telescopisch:	Ja
Verstelbaar:	Ja
Plafond montage buis lengte (max):	1220 cm
Plafond montage buis lengte (min):	610 cm