Atdec TH-3070-CTW Handleiding

Atdec Flat panel steun TH-3070-CTW

Lees hieronder de 📖 handleiding in het Nederlandse voor Atdec TH-3070-CTW (2 pagina's) in de categorie Flat panel steun. Deze handleiding was nuttig voor 36 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

G Attaching the Mount to the Ceiling Hanger

M8x10mm

Screw

Swivel Insert

Step 1

Attach the three Swivel Inserts to the hanger in the height that

you have chosen for the mounting of the display.

Step 2

Attach the front and rear Hanger Pole Collar so that it sits on

the swivel collars as shown above. Tighten the M8x30mm

screws so that the hanger pole collars is secure, however do

not over tighten.

Note: This operation will require two persons.

Lift the display with brackets attached and hook the brackets over the

sliders. Hold the display firmly and insert the two M8x45mm screws

and tighten by using the Long 6mm Allen Key.

Note: The brackets

should rest on the

horizontal bar with the

slider between the

bracket.

I Mounting the Display

Swivel Insert

Collar Front

Collar Rear

H Attaching the Mount to the Ceiling Hanger

Ceiling

Mount

Cables

Step 1

To use the in-built cable management, remove the Ceiling

Mount Cover and feed the cables through the cable hole.

Step 2

Cut out enough space in the Ceiling Mount Cover to allow

the cables to exit from, then push the Ceiling Mount Cover

up, until in sits flush with ceiling.

Ceiling Mount

Cover

Ceiling Mount

Cover

Cables

Ceiling

Mount

Cut Out

M8x30mm

Screws

No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.

Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 11.09.08 C

J Adjusting the Viewing Position of your Display

Step 1

Loosen the two M8x45mm screws, and adjust the

tilt angle of the display to the required position.

Tighten the two locking screws with the Long

6mm Allen Key provided.

WARNING: Do not attempt to adjust tilt

angle without firstly loosening locking

screws.

Doing so may damage the product.

6mm Allen Key

To adjust the pan position of the display, rotate the Hanger Pole

Collar to the desired position. Once in position, tighten all 4

M8x30mm screws as tight as possible to lock the display in

position.

Adjust grub screw 1 until the display sits level. Once the

display is level, tighten grub screw 2 until it firmly tightens onto

the horizontal bar. Tighten grub screw 3 firmly until it firmly

tightens onto the horizontal bar and prevents it from moving.

360° Rotation

Tighten

-5° to 5°

K Attaching the Adhesive Vinyl

Adhesive

Vinyl

M8 Small

Washer

M8x45mm

Screw

Long 6mm

Allen Key

Tighten

Loosen

-5° to 25°

Tilt

Hanger

Horizontal Bar

1. Tilt Adjust

Component Checklist

M10 Steel

Washer (x4)

Nylon Plug

(x4)

M8 x55mm

Screw

M10 Coach

Screw (x4)

A Mounting the Ceiling Mount

NOTE:

The manufacturer

does not accept

responsibility for

incorrect installation.

The installer should

satisfy himself that the

ceiling is strong

enough to support the

Telehook Flat Panel

Ceiling Mount unit of

14kgs (31lbs) plus the

maximum allowable

monitor weight of

91kgs (200lbs).

Total of 105kgs

(231lbs).

Telehook Flat Panel

Ceiling Mount

supports a maximum

weight of 91kgs

(200lbs)

TOOLS REQUIRED:

zPower Drill

z12mm (1/2”) Drill Bit

z7mm (9/32”) Drill Bit

zAdjustable wrench

Ceiling Mount

IMPORTANT:

Ensure you have received all parts against the component checklist prior to installing.

Bits Box

12mm (1/2”)

Hole

Nylon Plug

M10 Coach

Screw

Masonry

Ceiling

Masonry Mounting Option

Timber Beam Mounting Option

Timber

Beam

M10 Coach

Screw

7mm (9/32”)

Hole

Inner Hanger

M8 x10mm

Screw (x24)

M6 x12mm

Grub Screw

(x3)

M10 Washer

Collar Front Collar Rear Swivel Insert

(x3)

Adhesive Vinyl

Strip (x6)

M8x30mm

Screw (x4)

NOTE: Ensure all four M10 Coach Screws are used when mounting the Ceiling Mount.

Note: The Vinyl Strips may need to be cut to length

depending on the hanger configuration chosen.

The Telehook Flat Panel Ceiling Mount’s

set up is now complete. The remaining

unused holes can be covered using the

6 white adhesive vinyl strips for improved

aesthetics. Peel the backing from the

strip and apply the adhesive side onto

the hanger(s) so that they cover the

unused holes. Padlock

(not supplied)

5mm (3/16”)

diameter shackle

For added security you may

choose to attach a padlock to

one or both brackets to prevent

the theft of the display. It is

recommended that the padlock

should have a shackle diameter

of 5mm (3/16”).

L Security Option

2. Pan Adjust 3. Horizontal Adjust

Wall Mount Horizontal Bar

Slider (x2)

Hanger Joiner

Extension Hanger

Collar Joiner

Installation Instructions

Flat Panel Ceiling Mount

M8 x45mm

Locking Screws

(x2)

Multi

Washer (x6)

M5 x16mm

Mounting

Screws (x6)

M6 x16mm

Mounting

Screws (x6)

M8 x16mm

Mounting

Screws (x6)

M4 x16mm

Mounting

Screws (x6)

Long 6mm

Allen Key

M8 Small

Washer

(x2)

3mm

Allen Key

5mm

Allen Key

M8 Small

Washer

M8x45mm

Screw

Long 6mm

Allen Key

Tighten

6mm Allen

Key

TH-3070- CTW

Ceiling Mount Cover

Wall Mount Bracket (Left) Wall Mount Bracket (Right)

Clinch Nuts

B Attaching the Ceiling Mount Cover

Slide cover plate up.

Ceiling Mount

Cover

If the ceiling mount is attached where a false ceiling is used,

the ceiling mount cover should be used to hide the hole in

the false ceiling.

Ceiling Mount

Cover

Ceiling Mount

False Ceiling

C Mounting Options

Option 1:

To mount the display from 220mm (811/16”) to 470mm (181/2”)

please use the above set up as shown. Settings are at 50mm

(2”) increments.

*See note.

Ceiling Mount

Cover

Option 2:

To mount the display from 650mm (251/2”) to 1000mm

(393/8”) please use the above set up as shown. The Inner

Hanger position can be adjusted at 50mm (2”) increments.

Ceiling Mount

Cover

Ceiling Mount

M8x10mm

Screws

There are four possible mounting options for the Telehook Flat Panel Ceiling Mount. The selected mounting option will be deter-

mined by the required distance from the ceiling to the centre of the display.

Ceiling Mount

Option 1: 220mm (811/16”) - 470mm (181/2”) Option 2: 650mm (251/2”) - 1000mm (393/8”)

Inner Hanger

Collar Joiner

Option 3:

To mount the display from1070mm (421/8”) to 1820mm (715/8”)

please use the above set up as shown. The Inner Hanger

position can be adjusted and the Collar can be mounted along

the holes on the Extension hanger. Settings are at 50mm (2”)

increments.

*See Note.

Ceiling Mount

Cover

Option 4:

To mount the display from 1650mm (65”) to 2000mm (783/8”)

please use the above set up as shown. Note that the Inner

Hanger position can be adjusted, and that the Collar will be

mounted to the Collar Joiner. Settings are at 50mm (2”)

increments.

Ceiling

Mount Cover

Ceiling Mount

M8x10mm

Screws

Ceiling Mount

Option 3: 1070mm (421/8”) - 1820mm (715/8

”) Option 4: 1650mm (65”) - 2000mm (783/8”)

Extension

Hanger

Collar Joiner

M8x10mm

Screws

Extension

Hanger

Inner Hanger

Point of Contact

*NOTE:

If you intend to mount the display along the hanger

as per Option 1 or Option 3, you may choose to cut

the excess hanger, for improved aesthetics and cable

management.

Cut

Inner Hanger

Hanger Joiner

D Attaching the Brackets to the Display

M8 Screw Hole

M6 Screw Hole

M5 & M4

Screw Hole

Step 2:

Use the supplied Multi Washer as shown

above. Ensure that the tightest fitting hole

in the washer is used for the specific size

screw. Note distance X, for use in

the following steps.

== =

TOP

Clinch Nuts

Multi Washer

Step 1

Attach left and right brackets to the rear of your display. Select M4, M5, M6 or M8 fasteners to suit your display. Ensure

a minimum of 2 fasteners are used per bracket. Clinch nuts must be positioned as shown (internally).

E Attaching Horizontal Rail

Collar Front

Step 1

Insert the Horizontal Bar into the Hanger Pole Collar. Ensure

the slots on the Horizontal Bar are facing towards the Collar.

Insert the M8x55mm Screw to hold the bar in position.

Loosely insert the three M6x12mm grub screws.

M8x55mm

Screw

M6x12mm

Grub Screw

Horizontal

Rail

Step 2

Attach the two sliders to the Horizontal Bar, one on either

side. Tighten the grub screw into the slot, however do not

tighten firmly as the position will need to be adjusted to suit

your display.

Slider

Grub Screw

Slot

Horizontal Bar

F Position Sliders

= =

Slider

Grub

Screw Step 2

Secure slider in position and tighten firmly with

supplied allen key. Ensure that the grub screw

tightens into the slot on the horizontal bar.

Tighten

Distance X

Step 1

Accurately position sliders at Distance X as recorded in Section D. Ensure the

Sliders are equally spaced along the centre Horizontal Bar.

5mm

Allen Key

3mm Allen Key

Product specificaties

Merk:	Atdec
Categorie:	Flat panel steun
Model:	TH-3070-CTW
Kleur van het product:	Wit
Gewicht:	91 kg
Montagewijze:	Muur
Geschikt voor schermmaten:	30 - 65 "
Horizontaal draaibaar:	5 °
Gewicht (imperiaal):	200 lbs
Scharnier:	360°
Bereik kantelhoek:	-5 - 25 °
Bevestigingsstandaard:	VESA & nonVESA 180mm x 685mm / 100mm x 430mm
Maximum afstand tot plafond:	2000 mm