Atdec TH-1030-VFM Handleiding

Atdec Flat panel steun TH-1030-VFM

Lees hieronder de 📖 handleiding in het Nederlandse voor Atdec TH-1030-VFM (4 pagina's) in de categorie Flat panel steun. Deze handleiding was nuttig voor 49 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Step 7. Final Adjustment

Installation Complete

Your Telehook Wall Mount Swing Arm is complete and ready to use.

Position and angle your Display as desired, ensuring the Swing Arm moves freely.

Adjust the tension of the joints to suit, using the Allen Keys supplied.

4mm Allen Key

6mm Allen Key

As Display Manufacturers are constantly releasing new monitor models, Atdec does not accept responsibility if the VESA mounting does not comply with the international standards.

Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 27.11.09 ©

LOOSEN

T GHTENI

LOOSEN T GHTENI

Step 6. Cable Management

127( Leave enough

slack in the cables to

allow for full movement.

Connect cables

Cable Cover (x2)

Cable Clip

To utilise the Telehook Swing Arm cable

management system, use the Cable Covers

and Cable Clip as shown.

IM A I F MA IPORT NT N OR T ON

,03257$17,QVWDOO7HOHKRRN:DOO0RXQW6ZLQJ$UPDVSHU ,QVWDOODWLRQ,QVWUXFWLRQVWKH

! Telehook Wall Mount Swing Arm supports displays weighing up to 20kg (44lbs), with VESA hole configurations:

75x75mm (3”x3”), 100x100mm (4”x4”), *200x100mm (8”x4”), and *200x200mm (8”x8”) (*using extension tabs supplied)

! The Manufacturer accepts no responsibility for incorrect installation.

Step 1. Check Components

Check you have received all parts against the Component Checklist and Hardware above.

Step 2. Installing the Wall Bracket

Component Checklist

Stud

Masonry Wall

Nylon Anchor (x2)

Wall Mount

Screw (x2)

Wall Mount

Screw (x2)

Wall Material

H ward are

Flat Screen Wall Mount | Swing Arm

Installation Instructions

TOOL RE RES QUI D:

Power Drill

4mm ( 5/32”) Drill Bit

11mm ( 7/16

”) Masonry Drill Bit

Phillips Head Screwdriver

Spirit Level

Mounting to a Mounting to a 7LPEHU6WXG:DOO 0DVRQU\:DOO:

7+9)0

Swing Arm

Vesa Plate

- Position the Wall Bracket vertically on the wall and mark the

2 mounting holes (use a spirit level to check).

- Drill two 60mm (23/8“) deep holes using an 11mm (7/16”)

masonry drill bit.

- Secure the Wall Bracket using the Wall Mount Screws and

Nylon Anchors supplied.

- Position Wall Bracket vertically on the wall and mark the

2 mounting holes (use a spirit level to check).

- Drill two 60mm (23/8”) deep holes using a 4mm (5/32 ”) drill bit.

- Secure the Wall Bracket using the Wall Mount Screws supplied.

2.5mm Allen Key

4mm Allen Key

5mm Allen Key

6mm Allen Key

Washer (x4)

Nylon Anchor (x2)

Wall Mount Screw (x2)

Wall Bracket

Extension

Tabs (x4)

E wxtension Mounting Scre s

M4x12mm/M4x16mm (x4 each)

M5x12mm/M5x16mm (x4 each)

M6x12mm/M6x16mm (x4 each)

Display Mounting Scre sw

M5x12mm (x4)

75 or 100mm

VESA

Top of

Display

Ste 4. Att ch the VESA te t ur p a pla o yo Display

Fasten the VESA plate to your Display using the Display Mounting screws and Washers provided.

Select the appropriate size screw to suit your Display.

Display Mounting Screw (x4)

Top of VESA plate

Washer (x4)

Display Mounting hole

Back of Display

Ste 3. Att ch the Exten n b t the VESA te p a sio Ta s o pla (optional)

Only use the Extension Tabs if the display you wish to mount has a 200x200mm (8”x8”),

or 200x100mm (8”x4”) VESA hole mounting configuration.

If not, skip to Step 4.

200mm (8”)

Secure the Extension Tabs to the VESA plate using

the M5x12mm Extension Mounting Screws supplied.

M5x12mm

Screw (x4)

Extension

Tab (x4)

VESA

plate

TIGHT NE

FIRMLY

OPTION - 200 200mm (8” 8”)A x x

200mm (8”)

OPTION B - 200 100mm (8” ”)x x4

100mm (4”) Extension

Tab (x4)

VESA

plate

M5x12mm

Screw (x4)

TIGHT NE

FIRMLY

NOTE: Position the Extension Tabs to

suit your display mounting hardware.

Large Hole

(M6-M8)

Small Hole

(M4-M5)

( required)

Ste 5. Att ch ur t the Sw ng Arp a yo Display o i m

Back of

Display

TIGHT NE

Tighten both grub screws with the

2.5mm Allen Key supplied.

Slot the VESA plate on to the Swing Arm.

Ensure the display is level,

using the horizontal

adjustment.

+/- °5

r t t no a io

5mm

Allen Key

Product specificaties

Merk:	Atdec
Categorie:	Flat panel steun
Model:	TH-1030-VFM
Kleur van het product:	Zwart
Gewicht:	20 kg
Montagewijze:	Muur
Geschikt voor schermmaten:	-10 - 20 "
Horizontaal draaibaar:	5 °
Gewicht (imperiaal):	44 lbs
Scharnier:	360°/190°
Bereik kantelhoek:	-10 - 20 °
Bevestigingsstandaard:	VESA 50 x 50 / 75 x 75 / 100 x 100 / 200 x 100 / 200 x 200