Atdec SD-DP-750 Handleiding

Atdec Flat panel steun SD-DP-750

Lees hieronder de 📖 handleiding in het Nederlandse voor Atdec SD-DP-750 (2 pagina's) in de categorie Flat panel steun. Deze handleiding was nuttig voor 49 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Component Checklist

Donut Pole 420mm (16½”)

Hardware

Desk Clamp

Bra cket (x1)

IMPORTANT INFORMATION

UÊEach Quickshift Donut supports a maximum weight of 12kg (26½lbs)

o Donut Pole 420mm supports a total of: 12kg (26½lbs)

o Donut Pole 750mm supports a total of: 24kg (53lbs)

o Donut Pole 1150mm supports a total of: 36kg (79½lbs)

UÊ

This product suits VESA compliant displays with 75mm x 75mm (3” x 3”) and 100mm x 100mm (4” x 4”) mounting hole patterns.

UÊThe manufacturer does not accept responsibility for incorrect installation



Check you have received all parts against this component checklist according to the product you have purchased.

Quickshift

Donut (x1)

Cable

Ball (x2)

Cable

Clip (x2)Base Casting (x1)

M8 x 30mm

Screw (x1)

Bolt Through

Washer (x1)

2mm Allen

Key (x1)

Mounting Screws

M4 x 10mm (x4)

M4 x 12mm (x4)

M4 x 16mm (x4)

TOOLS REQUIRED:

UÊ*ower Drill

UÊ£0mm (3/8”) or 6mm (1/4”)

Drill Bit

UÊ*hillips Head Screw Driver

Pressure

Plate (x1)

M8 Desk Clamp

Screw (x1)

5mm Allen

Key (x1)

Step 1. Mounting Options

There are two Mounting Options: Bolt Through and Desk Clamp

To use the Bolt Through system, (Suits desktop thicknesses of 12mm-40mm [

1/2”-1

1/2”]) follow the Bolt Through instructions at Option A.

To use the Desk Clamp, (Suits destop thicknesses of 12mm-38mm [

2”-1

1/2”]) follow the Desk Clamp instructions at Option B.

Option A. Bolt Through



NOTE: It is recommended

that the pole assembly be

mounted towards the rear

edge of the work surface.

Bolt Through

Washer

M8 Desk

Clamp Screw

5mm Allen Key

Tighten Firmly

Note: Only one Desk Clamp Box is included in every Donut Pole purchased.

Donut Pole 750mm (29½”) Donut Pole 1150mm (45¼”)

Desk Clamp

Installation Instructions

Donut Pole | 420mm / 750mm / 1150mm

Option B. Desk Clamp

Attach the Desk Clamp

Bracket to the bottom of

the Pole Assembly using

the M8 x 30mm Screw.

Tighten Firmly using

the 5mm Allen Key.

Ensure the Spacedec

Logo on the Base

Casting is facing the

front as shown.

Desk Clamp

Bracket

M8 x 30mm

Screw

Base Casting

5mm Allen

Key

Work surface

Pressure

Plate

M8 x 30mm

Screw

5mm

Allen Key Tighten

Firmly

Attach the Donut Pole

Assembly using the

Desk Clamp as shown.



Note: Desk Clamp

suits 12mm (

1/2

”)

- 38mm (11/2”) thick

work surfaces.

Adjust the height of

the Pressure Plate

to suit your work

surface.

Ensure cable slot

is facing the back

Quickshift

Donut (x1)

Quickshift

Donut (x1)

Drill a 9mm (3/8”) hole in the

work surface at the desired

position and assemble as

shown.

Security

Screw (x1)

SD-DP-420

SD-DP-750

SD-DP-1150

Pole Assembly

Base

Casting 9mm (3/8”)

hole

Work surface

Ensure cable slot is

facing the back

VESA

plate (x1)

VESA

plate (x1)

VESA

plate (x1)

Step 3. Attach your Display to the Quickshift Donut

TIGHTEN

2mm

Allen Key

Hook the top of the VESA plate onto the

Quickshift Mount.

Insert the Security Screw, and tighten

using the 2mm Allen Key.

CLICK

Gently push the bottom of the Display

into the Mount until you hear a ‘CLICK’.

Back of

Display

No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.

Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 22.05.09©

Connect cables to your Displays,

routing them down the rear of the poles.

Push the cables into the slots, using

either the Cable Balls or Cable Clips

to secure them to the pole as shown.

Note: Ensure enough slack

is left in cables to allow for

movement. When the slot in

each pole cannot be used,

use the supplied Cable Clips

to secure the display cables.

Step 5. Adjust the VESA Ball Mount Step 6. Cable Management

Step 4. Adjust the height of the Quickshift Donut

Step 2. Attach the VESA plate to your Display

Top of

Display

There are two mounting hole configurations:

UÊÇxÊÝÊÇx

UÊ£ääÊÝÊ£ää

Choose appropriate Mounting Screws

from the Hardware supplied to suit

your Display.

Mounting Screws (x4)

VESA Plate

Back of Display

Çx

(3”) £ää

(4”)

Çx

(3”)

£ää

(4”)

Tighten (+Kg)

Loosen (-Kg)

Tightening

Tool

Tension

Plate

VESA plate

TIGHTEN

LOOSEN CLOSE

OPEN

Position your Display to the desired viewing angle, using

the 40° angular movement allowed by the VESA Ball Mount.

If the display does not hold its position, or is too resistant,

adjust the Tension Plate (see diagram below).

To make any adjustments, use the Tightening Tool supplied.

Cable

Balls (x2)

Cable

Clips

Open the lever to loosen the

Quickshift Donut.

Slide the Quickshift Donut to

desired position.

Close the lever to lock the

Quickshift Donut in place.

If necessary, adjust the tension

between the Donut and the Pole

using the 5mm Allen key supplied.

Product specificaties

Merk:	Atdec
Categorie:	Flat panel steun
Model:	SD-DP-750
Kleur van het product:	Zwart
Montagewijze:	Bureau
Maximale gewichtscapaciteit:	24 kg
Draaihoek:	360 °
Pan bereik:	-40 - 40 °
Bereik kantelhoek:	-40 - 40 °
Bevestigingsstandaard:	VESA 75mm x 75mm, 100mm x 100mm, 200mm x 100mm