Atdec AF-AT-D Handleiding

Atdec Flat panel steun AF-AT-D

Lees hieronder de 📖 handleiding in het Nederlandse voor Atdec AF-AT-D (4 pagina's) in de categorie Flat panel steun. Deze handleiding was nuttig voor 47 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

AF-AT-D Page 1 of 4

COMPONENT CHECKLIST

VESA

head

(x2)

Primary arm

cable cover

(x2)

Secondary arm

cable cover

(x2)

Pole Assembly

(x1)

Desk clamp

assembly

(x1)

M8 x 30mm

Screw

(x1)

Steel

washer

(x1)

M8 x 60mm

Screw

(x1)

Pole

top cap

(x1)

Bolt through

base

(x1)

Security Screw

M4 x 16mm

(x2)

Cable

stop

(x2)

Cable

clip

(x2)

Dual arm

assembly

(x1)

5mm

Allen key

(x1)

Mounting

screws

M4 x 10mm

(x8)

Mounting

screws

M4 x 12mm

(x8)

Mounting

screws

M4 x 16mm

(x8)

Installation Guide

AF-AT-D

Dual Arm

Desktop Monitor Mount

IMPORTANT INFORMATION

! Please ensure this product is installed as per these installation instructions.

! This product is compatible with the range of AF Poles and arms.

! The manufacturer accepts no responsibility for incorrect installation.

REQUIRED TOOLS

WEIGHT RANGE

• Power Drill

• Drill Bit

• Phillips Head Screwdriver

0 - 8kg

(0 - 17.6lbs)

per screen

AF-AT-D Page 2 of 4

1. Desk overview

The desk clamp bracket

can be repositioned to

suit different mounting

surface thicknesses

1.1 1.2 Default Inverted

2. How to reconfigure desk clamp

2.1 Remove screws

(M8 x 16mm Countersunk screw)

2.2 Remove clamp plate Invert bracket Replace clamp plate Reattach bracket2.3 2.4 2.5

Pressure Plate

M10 Desk Clamp Screw

5mm Allen Key

M8 x 30mm

Countersunk

screw Tighten

firmly

3.2 Place in desired location Screw pressure plates in and .3.3 tighten firmly3.1 Attach clamp to post

Drill 9mm hole in

desired post position

on work surface

3. Post mount configuration

4. Bolt through

9mm

(3/8”)

25mm

offset

MIN THICKNESS - 0mm (0”)

MAX THICKNESS - 39mm (1.5”)

MIN THICKNESS - 35mm (1.4”)

MAX THICKNESS - 76mm (3”)

5. Installing bolt through

5.1 Attach plate to post

Align rear hole with

hole on desk

5mm

Allen Key

M8x60mm

Screw

Bolt

Through

Plate

AF-AT-D Page 3 of 4

6. Install VESA monitor head

Optional Spacers (may be

required for recessed and

uneven surfaces)

VESA monitor

head

Screen

M4x10/12/16mm

Phillips Head Mounting

Screws

6.1 Install VESA monitor head as shown. 100mm

100mm

Double Arm

Assembly

7. Install arm assembly

Handgrip Tab

5mm

Allen Key

Pole

Top Cap

7.1 Unlock handgrip and raise so

that handgrip tab protrudes

7.3 Slide the double arm assembly and

Handgrip down the pole before locking

the handgrip at the desired height

7.4 Insert Pole

Top Cap into

Pole. This is also

where the Allen

Key is stored.

7.2 Slip the double arm assembly

over the handgrip tab and then

onto the pole

8. Mounting Monitor

VESA monitor head

Arm Assembly

8.2 OPTIONAL SECURITY SCREW

Ensure the Monitor is supported, then loosen the

Monitor head screw with the 5mm Allen Key and

tilt screen up before installing the M4 x 16mm

Security Screw into the Security Screw hole

8.1 Insert VESA monitor head into

the receptacle in the Arm Assembly

5mm Allen Key

Phillips Head

Screwdriver

Loosen

Tighten

Security Screw

Hole

M4 x 16mm

Security Screw

Monitor head

screw

Note: Support Screen

when adjusting tilt.

Note: Back to back configurations

may result in clamp failure

Product specificaties

Merk:	Atdec
Categorie:	Flat panel steun
Model:	AF-AT-D
Kleur van het product:	Zilver
Gewicht verpakking:	3800 g
Breedte verpakking:	235 mm
Diepte verpakking:	560 mm
Hoogte verpakking:	115 mm
Materiaal behuizing:	Aluminium, Plastic
In hoogte verstelbaar:	Ja
Maximale gewichtscapaciteit:	8 kg
Paneelmontage-interface:	75 x 75, 100 x 100 mm
Aantal per verpakking:	1 stuk(s)
Inclusief schroeven:	Ja
Draaihoek:	240 °
(Buitenste) hoofdverpakking hoogte:	250 mm
(Buitenste) hoofdverpakking breedte:	485 mm
(Buitenste) hoofdverpakking brutogewicht:	16200 g
(Buitenste) hoofdverpakking lengte:	575 mm
Hoeveelheid per (buitenste) hoofdverpakking:	4 stuk(s)
Type product:	Flatscreen bevestigingsarm
Bereik kantelhoek:	-70 - 70 °