Aruba Instant AP-104 Handleiding

Aruba Access point Instant AP-104

Lees hieronder de 📖 handleiding in het Nederlandse voor Aruba Instant AP-104 (2 pagina's) in de categorie Access point. Deze handleiding was nuttig voor 24 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

AP-100 Series Wireless Access Point

Installation Guide

About the Aruba AP-100 Series Access Points

The Aruba AP-104 and AP-105 wireless access points support the IEEE 802.11n

standard for high-performance WLAN. This access point uses MIMO (Multiple-in,

Multiple-out) technology and other high-throughput mode techniques to deliver

high-performance, 802.11n 2.4 GHz and 5 GHz functionality while simultaneously

supporting existing 802.11a/b/g wireless services. The AP-100 Series access point

works only in conjunction with an Aruba Controller.

The Aruba AP-100 Series access point provides the following capabilities:

Wireless transceiver

Protocol-independent networking functionality

IEEE 802.11a/b/g/n operation as a wireless access point

IEEE 802.11a/b/g/n operation as a wireless air monitor

Compatibility with IEEE 802.3af PoE

Central management configuration and upgrades through an Aruba

Controller

Package Contents

AP-104 or AP-105 access point

Installation guide (this document)

AP-100 Series Hardware Overview

Figure 1 AP-100 Front (AP-104 shown)

LEDs

The AP-100 Series is equipped with four LEDs that indicate the status of the

various components of the AP.

PWR: Indicates whether or not the AP-100 Series is powered-on

ENET: Indicates the status of the AP-100 Series’s Ethernet port

11A/N: Indicates the status of the 802.11a/n radio

11B/G/N: Indicates the status of the 802.11b/g/n radio

For information about the AP-100 Series’s LED behavior, see .Table 1 on page 2

External Antenna Connectors

The AP-104 is designed for use with external antennas and equipped with four

external, female RP-SMA antenna connectors. Antenna connector mapping:

R0/A0: Radio 0 (5GHz), chain 0

R0/A1: Radio 0 (5GHz), chain 1

R1/A0: Radio 1 (2.4GHz), chain 0

R1/A1: Radio 1 (2.4GHz), chain 1

The AP-105 is equipped with internal antennas.

Figure 2 AP-100 Series Rear

Console Port

Use the console port to connect to a terminal for direct local management.

Ethernet Port

AP-100 Series is equipped with a single 10/100/1000Base-T (RJ-45) auto-sensing,

MDI/MDX wired-network connectivity port. This port supports IEEE 802.3af

Power over Ethernet (PoE) compliance, accepting 48VDC as a standard defined

Powered Device (PD) from a Power Sourcing Equipment (PSE) such as a PoE

midspan injector, or network infrastructure that supports PoE.

DC Power Socket

If PoE is not available, an optional Aruba AP AC-DC adapter kit (sold separately)

can be used to power the AP-100 Series.

Reset Button

The reset button can be used to return the AP to factory default settings. To reset

the AP:

1. Power off the AP.

2. Press and hold the reset button using a small, narrow object, such as a

paperclip.

3. Power-on the AP without releasing the reset button. The power LED will

flash within 5 seconds.

4. Release the reset button.

The power LED will flash again within 15 seconds indicating that the reset is

completed. The AP will now continue to boot with the factory default settings.

Before You Begin

Pre-Installation Network Requirements

After WLAN planning is complete and the appropriate products and their

placement have been determined, the Aruba controller(s) must be installed and

initial setup performed before the Aruba APs are deployed.

For initial setup of the controller, refer to the for ArubaOS Quick Start Guide

the software version installed on your controller.

AP Pre-Installation Checklist

Before installing your AP-100 Series AP, ensure that you have the following:

CAT5 UTP cable of required length

One of the following power sources:

IEEE 802.3af-compliant Power over Ethernet (PoE) source

Supports full functionality for AP-100 Series

The POE source can be any power source equipment (PSE) controller or

midspan PSE device

Aruba AP AC-DC adapter kit (sold separately)

Aruba Controller provisioned on the network:

Layer 2/3 network connectivity to your access point

One of the following network services:

Aruba Discovery Protocol (ADP)

DNS server with an “A” record

DHCP Server with vendor-specific options

Summary of the Setup Process

Successful setup of an AP-100 Series access point consists of five tasks, which

must be performed in this order:

1. Verify pre-installation connectivity.

2. Identify the specific installation location for each AP.

3. Install each AP.

4. Verify post-installation connectivity.

5. Configure each AP.

Verifying Pre-Installation Connectivity

Before you install APs in a network environment, make sure that the APs are

able to locate and connect to the controller after power on.

Specifically, you must verify the following conditions:

When connected to the network, each AP is assigned a valid IP address

APs are able to locate the controller

Refer to the Guide for instructions on locating and ArubaOS Quick Start

connecting to the controller.

Identifying Specific Installation Locations

You can mount the AP-100 Series access point on a wall or on the ceiling. Use the

AP placement map generated by Aruba’s RF Plan software application to

determine the proper installation location(s). Each location should be as close

as possible to the center of the intended coverage area and should be free from

obstructions or obvious sources of interference. These RF absorbers/reflectors/

interference sources will impact RF propagation and should have been

accounted for during the planning phase and adjusted for in RF plan.

Identifying Known RF Absorbers/Reflectors/Interference

Sources

Identifying known RF absorbers, reflectors, and interference sources while in

the field during the installation phase is critical. Make sure that these sources are

taken into consideration when you attach an AP to its fixed location.

RF absorbers include:

Cement/concrete—Old concrete has high levels of water dissipation, which

dries out the concrete, allowing for potential RF propagation. New concrete

has high levels of water concentration within the concrete, blocking RF

signals.

Natural Items—Fish tanks, water fountains, ponds, and trees

Brick

RF reflectors include:

Metal Objects—Metal pans between floors, rebar, fire doors, air conditioning/

heating ducts, mesh windows, blinds, chain link fences (depending on

aperture size), refrigerators, racks, shelves, and filing cabinets

Do not place an AP between two air conditioning/heating ducts. Make sure

that APs are placed below ducts to avoid RF disturbances.

RF interference sources include:

Microwave ovens and other 2.4 or 5 GHz objects (such as cordless phones)

Cordless headset such as those used in call centers or lunch rooms

Installing the AP

Using the Integrated Wall-Mounting Slots

The keyhole-shaped slots on the back of the AP can be used to attach the device

upright to an indoor wall or shelf. When you choose the mounting location, allow

additional space at the right of the unit for cables.

1. Since the ports are on the back of the device, make sure that you mount the

AP is such a way that there is a clear path to the Ethernet port, such as a pre-

drilled hole in the mounting surface.

2. At the mounting location, install two screw on the wall or shelf, 1 7/8 inches

(4.7 cm) apart. If you are attaching the device to drywall, Aruba recommends

using appropriate wall anchors (not included).

3. Align the mounting slots on the rear of the AP over the screws and slide the

unit into place (see ).Figure 3

Figure 3 Installing the AP-100 Series Access Point on a Wall

Using the Integrated Ceiling Tile Rail Slots

The snap-in tile rail slots on the rear of the AP can be used to securely attach the

device directly to a 15/16" wide, standard ceiling tile rail.

1. Pull the necessary cables through a prepared hole in the ceiling tile near

where the AP will be placed.

2. If necessary, connect the console cable to the console port on the back of the

AP.

Hold the AP next to the ceiling tile rail with the ceiling tile rail mounting slots at

approximately a 30-degree angle to the ceiling tile rail (see ). Make sure Figure 4

that any cable slack is above the ceiling tile.

Figure 4 Orienting the Ceiling Tile Rail Mounting Slots

3. Pushing toward the ceiling tile, rotate the AP clockwise until the device

clicks into place on the ceiling tile rail.

Inform your supplier if there are any incorrect, missing, or damaged parts. If

possible, retain the carton, including the original packing materials. Use

these materials to repack and return the unit to the supplier if needed.

PWR

ENET

11B/G/N

11A/N

External

Antenna

Connector

FCC Statement: Improper termination of access points installed in the

United States configured to non-US model controllers will be in violation of

the FCC grant of equipment authorization. Any such willful or intentional

violation may result in a requirement by the FCC for immediate termination

of operation and may be subject to forfeiture (47 CFR 1.80).

EU Statement:

Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands.

Please refer to the for details on restrictions.ArubaOS User Guide

Produit réseau local radio basse puissance operant dans la bande

fréquence 2.4 GHz et 5 GHz. Merci de vous referrer au ArubaOS User

Guide pour les details des restrictions.

Low Power FunkLAN Produkt, das im 2.4 GHz und im 5 GHz Band arbeitet.

Weitere Informationen bezlüglich Einschränkungen finden Sie im ArubaOS

User Guide.

Apparati Radio LAN a bassa Potenza, operanti a 2.4 GHz e 5 GHz. Fare

riferimento alla ArubaOS User Guide per avere informazioni detagliate sulle

restrizioni.

AP105_002

CONSOLE

ENET

12V 1.25A

48V 350mA

CONSOLE

ENET

Power

Connector

Reset Button

Aruba Networks, Inc., in compliance with governmental requirements, has

designed the AP-100 Series access points so that only authorized network

administrators can change the settings. For more information about AP

configuration, refer to the ArubaOS Quick Start Guide and ArubaOS User

Guide.

Access points are radio transmission devices and as such are subject to

governmental regulation. Network administrators responsible for the

configuration and operation of access points must comply with local

broadcast regulations. Specifically, access points must use channel

assignments appropriate to the location in which the access point will be

used.

Service to all Aruba Networks products should be performed by trained

service personnel only.

Make sure the AP fits securely on the ceiling tile rail when hanging the

device from the ceiling; poor installation could cause it to fall onto people

or equipment.

AP105_003

P105_004

AP-100 Series Wireless

Access Point

Installation Guide

www.arubanetworks.com

1344 Crossman Avenue

Sunnyvale, California 94089

Phone: 408.227.4500

Fax 408.227.4550

AP-100 Series Wireless Access Point | Installation Guide

Part Number 0511027-02 | April 2012

Contacting Aruba Networks

Table 1

Web Site Support

Main Site http://www.arubanetworks.com

Support Site https://support.arubanetworks.com

Software Licensing Site https://licensing.arubanetworks.com/login.php

Wireless Security Incident

Response Team (WSIRT)

http://www.arubanetworks.com/support/wsirt.php

Americas and APAC Support Email support@arubanetworks.com

EMEA Support Email emea.support@arubanetworks.com

WSIRT Email

Please email details of any security

problem found in an Aruba product.

wsirt@arubanetworks.com

Table 2

Telephone Support

Aruba Corporate +1 (408) 227-4500

FAX +1 (408) 227-4550

For Wireless That Works®, Mobile Edge Architecture, People Move. Networks Must Follow., RFProtect

®, The All

Wireless Workplace Is Now Open For Business, and The Mobile Edge Company® are trademarks of Aruba

Open Source Code

Certain Aruba products include Open Source software code developed by third parties, including software code

subject to the GNU General Public License ("GPL"), GNU Lesser General Public License ("LGPL"), or other Open

Source Licenses. The Open Source code used can be found at this site:

http://www.arubanetworks.com/open_source

Legal Notice

The use of Aruba Networks, Inc. switching platforms and software, by all individuals or corporations, to terminate

other vendors' VPN client devices constitutes complete acceptance of liability by that individual or corporation for

this action and indemnifies, in full, Aruba Networks, Inc. from any and all legal actions that might be taken against

it with respect to infringement of copyright on behalf of those vendors.

Warranty

This hardware product is protected by the standard Aruba warranty of one year parts/labor. For more information,

refer to the ARUBACARE SERVICE AND SUPPORT TERMS AND CONDITIONS.

Altering this device (such as painting it) voids the warranty.

Connecting Required Cables

Install cables in accordance with all applicable local and national regulations and

practices.

Ethernet Ports

The RJ45 Ethernet port (ENET) supports 10/100/1000Base-T auto-sensing MDI/

MDX connections. Use these ports to connect the AP to a twisted pair Ethernet

LAN segment or directly to an Aruba Controller. Use a 4- or 8-conductor,

Category 5 UTP cable up to 100 m (325 feet) long.

The 10/100/1000 Mbps Ethernet port is on the back of the AP. The port has an RJ-

45 female connector with the pin-outs shown in .Figure 5

Figure 5 Gigabit Ethernet Port Pin-Out

Serial Console Port

The serial console port (Console) allows you to connect the AP to a serial

terminal or a laptop for direct local management. This port is an RJ-45 female

connector with the pinouts described in . Connect this port in one of the Figure 6

following ways:

Connect it directly to a terminal or terminal server using an Ethernet cable.

Use a modular adapter to convert the RJ-45 (female) connector on the AP to a

DB-9 (male) connector, and connect the adapter to a laptop using an RS-232

cable. See for connector details of the adapter.Figure 7

Figure 6 Serial Port Pin-Out

Figure 7 RJ-45 (Female) to DB-9 (Male) Modular Adapter Conversion

Power Connection

The AP-100 Series has a single 12V DC power jack socket to support powering

through an AC-to-DC power adapter.

Verifying Post-Installation Connectivity

The integrated LEDs on the AP can be used to verify that the AP is receiving

power and initializing successfully (see ). Refer to the Table 1 ArubaOS Quick

Start Guide for further details on verifying post-installation network

connectivity.

Configuring the AP-100 Series

AP Provisioning/Reprovisioning

Provisioning parameters are unique to each AP. These local AP parameters are

initially configured on the controller which are then pushed out to the AP and

stored on the AP itself. Aruba recommends that provisioning settings be

configured via the ArubaOS Web UI only. Refer to the for ArubaOS User Guide

complete details.

AP Configuration

Configuration parameters are network or controller specific and are configured

and stored on the controller. Network configuration settings are pushed out to

the AP(s) but remain stored on the controller.

Configuration settings can be configured via the ArubaOS Web UI, ArubaOS CLI,

or Aruba MMS. Refer to their respective guides for further details: the ArubaOS

User Guide Aruba Mobility Management System User Guide or .

Product Specifications

Electrical

Ethernet:

1 x 10/100/1000Base-T auto-sensing Ethernet RJ-45 Interfaces

MDI/MDX

IEEE 802.3 (10Base-T), IEEE 802.3u (100Base-T). IEEE 802.3ab

(1000Base-T)

Power over Ethernet (IEEE 802.3af compliant), 48V DC/350mA (see Figure

5 for pin configuration)

Power:

12 VDC power interface, supports powering through an AC-to-DC power

adapter

For additional specifications on this product, please refer to the data sheet. The

data sheet can be found at .www.arubanetworks.com

Proper Disposal of Aruba Equipment

For the most current information about Global Environmental Compliance and

Aruba products, see our website at .www.arubanetworks.com

Waste of Electrical and Electronic Equipment

Aruba products at end of life are subject to separate collection

and treatment in the EU Member States, Norway, and

Switzerland and therefore are marked with the symbol shown

at the left (crossed-out wheelie bin). The treatment applied at

end of life of these products in these countries shall comply

with the applicable national laws of countries implementing

Directive 2002/96EC on Waste of Electrical and Electronic

Equipment (WEEE).

European Union RoHS

Aruba products also comply with the EU Restriction of

Hazardous Substances Directive 2002/95/EC (RoHS). EU

RoHS restricts the use of specific hazardous materials in

the manufacture of electrical and electronic equipment.

Specifically, restricted materials under the RoHS Directive are Lead (including

Solder used in printed circuit assemblies), Cadmium, Mercury, Hexavalent

Chromium, and Bromine. Some Aruba products are subject to the exemptions

listed in RoHS Directive Annex 7 (Lead in solder used in printed circuit

assemblies). Products and packaging will be marked with the “RoHS” label

shown at the left indicating conformance to this Directive.

China RoHS

Aruba products also comply with China environmental declaration

requirements and are labeled with the “EFUP 10” label shown at

the left.

Safety and Regulatory Compliance

Aruba Networks provides a multi-language document that contains country-specific

restrictions and additional safety and regulatory information for all Aruba access points.

This document can be viewed or downloaded from the following location:

www.arubanetworks.com/safety_addendum

The device is electronically labeled and the FCC ID will be displayed via the controller

WebUI under the About menu.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

EMC Compliance and Warning Statement

IEC 60601-1-2: 2007

EN 60601-1-2: 2007

The AP-105 has been tested and found to comply with the limits of the standard for

medical devices, IEC 60601-1-2:2007. The unit also complies with the requirements of EN

60601-1-2:2007, providing the presumption of compliance to the European Union’s Medical

Device Directive 2007/47/EC. The limits are designed to provide reasonable protection

against harmful interference in a typical medical installation. This equipment generates,

uses and can radiate radio frequency energy, and, if not installed and used in accordance

with the manufacturer’s instructions may cause harmful interference to other devices in

the vicinity. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment causes interference with other devices, which may be

determined by turning the equipment off and on, the user is encouraged to try and correct

the interference by one or more of the following measures:

Reorient or relocate the device receiving the interference.

Increase the separation between the equipment.

Connect the equipment into an outlet on a circuit different from that to which the

other device(s) are connected.

Consult the manufacturer or field service technician for help.

The Model AP-105 do not have an Applied Part as defined in IEC 60601-1. The protection

against electric shock is Class ll.

Device is not protected against ingress of liquids and has a protection class of IPX0 as

defined by IEC 60601-1 and IEC 60529. Equipment not suitable for use in the presence of

flammable mixtures.

The unit is considered “Continuous Operation” equipment as defined by IEC 60601-1.

Power Consumption – 48 VDC 802.3af power over Ethernet or 12VDC, 1.25A for external

AC supplied power (adapter sold separately); Maximum power consumption – 12.5W.

Mechanical Dimensions: 132mm x 135mm x 45mm; 300g.

Environmental: Operating Temp: 0° C to +50° C (+32° F to +122° F); Humidity: 5 to 95%

non-condensing. Storage Temp: -40° CS to +70° C (-40°F to +158°F).

If both POE and DC power are available, the AP uses POE even when there

is not enough POE voltage available to power the AP.

Table 1 AP-100 Series Series LED Meanings

LED Color/State Meaning

PWR Off No power to AP

Green flashing System initializing

Red steady System failed to

initialize, contact TAC

Green steady Power on, device ready

ENET

(10/100/1000 Mbps)

Off No link

Green on 1000 Mbps link

Amber on 10/100 Mbps link

Green flashing Ethernet link activity

1000Base-T Gigabit

Ethernet Port

RJ-45 Female

Pin-Out

Signal Name

BI_DC+

BI_DC-

BI_DD+

BI_DD-

BI_DA+

BI_DA-

BI_DB+

BI_DB-

Function

Bi-directional pair +C

Bi-directional pair -C

Bi-directional pair +D

Bi-directional pair -D

Bi-directional pair +A

Bi-directional pair -A

Bi-directional pair +B

Bi-directional pair -B

Serial

Console Port

TxD

GND

RxD

RJ-45 Female

Pin-Out

Direction

Input

Output

GND

6 3

RJ-45 DB-9

Internal

Connections

TxD

GND

RxD

TxD

GND

RxD

RJ-45 Female

Pin-Out

Direction

Input

Output

DB-9 Male

Pin-Out

TxD

RxD

Ground

Direction

Input

Output

11A/N Off 5 GHz radio is disabled

Amber 5 GHz radio enabled in

WLAN mode

Green 5 GHz radio enabled in

11n mode

Green flashing 5 GHz Air Monitor or RF

Protect mode

11B/G/N Off 2.4 GHz radio disabled

Amber 2.4 GHz radio enabled in

WLAN mode

Green 2.4 GHz radio enabled in

11n mode

Green flashing 2.4 GHz Air Monitor or

RF Protect mode

If a power adapter other than the one provided by Aruba Networks is used

in the US or Canada, it should be cULus (NRTL) Listed, with an output

rated 12 VDC, minimum 1.25A, marked “LPS” or “Class 2,” and suitable for

plugging into a standard power receptacle in the US and Canada.

Table 1 AP-100 Series Series LED Meanings

LED Color/State Meaning

RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure

limits. This equipment should be installed and operated with a minimum distance of 7.9 inches

(20 cm) between the radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter

must not be co-located or operating in conjunction with any other antenna or transmitter. When

operated in the 5.15 to 5.25 GHz frequency range, this device is restricted to indoor use to

reduce the potential for harmful interference with co-channel Mobile Satellite Systems.

᳝↦᳝ᆇ⠽䋼ໄᯢ

᳝↦᳝ᆇ⠽䋼ໄᯢ᳝↦᳝ᆇ⠽䋼ໄᯢ

Hazardous Materials Declaration

᳝↦᳝ᆇ⠽䋼៪ܗ㋴(Hazardous Substance)

䚼ӊৡ⿄

(Parts) 䪙

3E

∲

+J

䬝

&G

݁Ӌ䫀

&U





໮⒈㘨㣃

3%%

໮⒈Ѡ㣃䝮

3%'(

⬉䏃ᵓ

(

PCA Boards)

h ƻ ƻ ƻ ƻ ƻ

ᴎẄ㒘ӊ

(Mechanical Sub-Assemblies)

h ƻ ƻ ƻ ƻ ƻ



ƻ˖ 㸼⼎䆹

᳝

↦᳝ᆇ⠽䋼೼䆹䚼ӊ᠔᳝ഛ䋼ᴤ᭭Ёⱘ৿䞣ഛ೼

SJ/T11363-2006 󰵼ޚ㾘ᅮⱘ䰤䞣㽕∖ҹϟǄ

Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is

below the relevant threshold of the SJ/T11363-2006 standard.



h˖ 㸼⼎䆹

᳝

↦᳝ᆇ⠽䋼㟇ᇥ೼䆹䚼ӊⱘᶤϔഛ䋼ᴤ᭭Ёⱘ৿䞣䍙ߎ6-7󰵼ޚ㾘ᅮⱘ䰤䞣㽕∖Ǆ

Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials

in the parts is above the relevant threshold of the SJ/T11363-2006 standard.



ᇍ䫔ଂП᮹ⱘ᠔ଂѻકᴀ㸼ᰒ⼎կᑨ䫒ⱘ⬉ᄤֵᙃѻકৃ㛑ࣙ৿䖭ѯ⠽䋼Ǆ

This table shows where these substances may be found in the supply chain of electronic information

products, as of the date of sale of the enclosed product.

ℸ󰵼ᖫЎ䩜ᇍ᠔⍝ঞѻકⱘ⦃ֱՓ⫼ᳳ󰵼ᖫᶤѯ䳊䚼ӊӮ

᳝

ϔϾϡৠⱘ⦃ֱՓ⫼ᳳ

՟བ⬉∴ܗ῵ഫ䌈೼݊ѻકϞ

ℸ

⦃Փ⫼ᳳ䰤া䗖⫼Ѣѻકᰃ೼ѻક᠟ݠЁ᠔㾘ᅮⱘᴵӊϟᎹ԰

The Environment- Friendly Use Period (EFUP) for all enclosed products and their parts are

per the symbol shown here. The Environment- Friendly Use Period is valid only when the

product is operated under the conditions defined in the product manual.

200202320G

TRA

REGISTERED No:

DEALER No:

DA0039425/10

0019614/09

Product specificaties

Merk:	Aruba
Categorie:	Access point
Model:	Instant AP-104

Heb je hulp nodig?

Als je hulp nodig hebt met Aruba Instant AP-104 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Access point Aruba

Aruba AP-504 Handleiding

20 Augustus 2024

Aruba AP-318 Handleiding

19 December 2023

Aruba AP-577 Handleiding

19 December 2023

Aruba Instant IAP-175 Handleiding

30 Mei 2023

Aruba 205H Handleiding

25 Mei 2023

Aruba AP-93H Handleiding

25 Mei 2023

Aruba AP-503H Handleiding

8 Mei 2023

Aruba AP-567 Handleiding

7 Mei 2023

Aruba Instant IAP-175P Handleiding

29 April 2023

Aruba AP-375EX Handleiding

23 April 2023

Handleiding Access point

Nieuwste handleidingen voor Access point

TP Link Omada EAP115-Wall Handleiding

15 November 2024

Mikrotik LTAP Mini LTE kit Handleiding

15 November 2024

TP Link Festa F65-Wall Handleiding

3 Oktober 2024

D-Link DWL-1000AP+ Handleiding

23 September 2024

D-Link DWL-700AP Handleiding

21 September 2024

Cambium Networks cnPilot e505 Handleiding

11 September 2024

Cambium Networks cnPilot e425H Handleiding

11 September 2024

Cambium Networks cnPilot e600 Handleiding

11 September 2024

Cambium Networks cnPilot e510 Handleiding

11 September 2024

Cambium Networks cnPilot e502S Handleiding

11 September 2024