Aruba AP-504 Handleiding

Aruba Access point AP-504

Lees hieronder de 📖 handleiding in het Nederlandse voor Aruba AP-504 (13 pagina's) in de categorie Access point. Deze handleiding was nuttig voor 11 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/13

Aruba 500 Series Campus Access Points

Installation Guide

Rev01 | July 2019 1

The Aruba 500 Series campus access points (AP-504 and AP-505) are high-performance, dual-radio wireless

devices that can be deployed in either controller-based (ArubaOS) or controllerless (Aruba Instant) network

environments. These access points deliver high performance concurrent 2.4 GHz and 5 GHz 802.11ax Wi-Fi

functionality with MIMO radios (2x2 in 2.4 GHz, 2x2 in 5 GHz), while also supporting legacy 802.11a/b/g/n/ac

wireless services.

In addition to both Wi-Fi radios, these APs also incorporate a Bluetooth Low Energy (BLE) and Zigbee radio,

supporting a variety of use-cases and services, such as locationing and IoT.

A mount kit (sold separately) is needed to mount the AP. Make sure to purchase the correct mount kit for the

intended deployment of the AP.

Package Contents

Aruba 500 Series access point (with a pre-installed mount bracket)

Hardware Overview

The following sections outline the hardware components of the 500 Series access points.

Figure 1 AP-505 Front View

The AP mount bracket attaches to a variety of mount kits (sold separately).

Inform your supplier if there are any incorrect, missing, or damaged parts. If possible, retain the carton, including

the original packing materials. Use these materials to repack and return the unit to the supplier if needed.

2 Aruba 500 Series Campus Access Points | Installation Guide

Figure 2 AP-504 Front View

External Antenna Connectors

The AP-504 access points are equipped with two external antenna connectors located on the front

corners of the access point (see Figure 2). Antenna ports A0 and A1(corresponding with radio chain 0

and 1), are used for both radios and bands (RF signals are diplexed).

External antennas for this device must be installed by an Aruba Certified Mobility Professional (ACMP) or other

Aruba-certified technician, using manufacturer-approved antennas only.

The Equivalent Isotropically Radiated Power (EIRP) levels for all external antenna devices must not exceed the

regulatory limit set by the host country/domain.

Installers are required to record the antenna gain for this device in the system management software. A list of

approved antennas can be found at: http://www.arubanetworks.com/assets/og/OG_AP-500Series.pdf.

Les antennes externes pour cet appareil doivent être installées par un professionnel de la mobilité certifié Aruba

(ACMP) ou un autre technicien certifié Aruba, en utilisant uniquement des antennes approuvées par le fabricant.

Les niveaux équivalents de puissance à rayonnement isotrope (EIRP) pour tous les périphériques d'antenne

externe ne doivent pas dépasser la limite réglementaire définie par le pays hôte / domaine.

Les installateurs doivent enregistrer le gain d'antenne pour cet appareil dans le logiciel de gestion du système.

Une liste d'antennes approuvées peut être trouvée à http://www.arubanetworks.com/assets/og/OG_AP-

500Series.pdf.

Aruba 500 Series Campus Access Points | Installation Guide 3

Figure 3 LEDs (AP-505 shown)

LEDs

System Status

The System Status LED indicates the operating condition of the access point.

Table 1 System Status LED

Radio Status

The Radio Status LED indicates the operating mode of the access point’s radios.

Table 2 Radio Status LEDs

Color/State Meaning

Off Device Powered off

Green- solid Device ready, fully functional, no network restrictions

Green- blinking 1

1. Blinking: one second on, one second off, 2 seconds cycle.

Device booting, not ready

Green- flashing off 2

2. Flashing off: mostly on, fraction of a second off, 2 seconds cycle.

Device ready, fully functional, uplink negotiated in sub-optimal speed (<1Gbps)

Green- flashing on 3

3. Flashing on: mostly off, fraction of a second on, 2 seconds cycle.

Device in deep-sleep mode

Amber- solid Device ready, restricted power mode (IPM restrictions applied), no network

restrictions

Amber- flashing off Device ready, restricted power mode (IPM restrictions applied), uplink negotiated

in sub-optimal speed (<1Gbps)

Red System error condition - Immediate action required

Color/State Meaning

Off Device powered off, or both radios disabled

Green- solid Both radios enabled in access mode

Green- blinking One radio enabled in access mode, other disabled

Amber- solid Both radios enabled in monitor mode

Product specificaties

Merk:	Aruba
Categorie:	Access point
Model:	AP-504
Kleur van het product:	Wit
Gewicht:	500 g
Breedte:	160 mm
Diepte:	161 mm
Hoogte:	37 mm
Plaatsing:	Ceiling, Wall
USB-connectortype:	USB Type-A
Aantal USB 2.0-poorten:	1
Aantal Ethernet LAN (RJ-45)-poorten:	1
Bevestigingsmogelijkheid voor kabelslot:	Ja
Kabelslot sleuf type:	Kensington
MIMO:	Ja
Modulatie:	16-QAM, 64-QAM, 256-QAM, 1024-QAM, BPSK, CCK, QPSK
Ethernet LAN, data-overdrachtsnelheden:	10,100,1000 Mbit/s
Netwerkstandaard:	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11ax, IEEE 802.11b, IEEE 802.11g, IEEE 802.11n, IEEE 802.3af, IEEE 802.3at, IEEE 802.3az
Ondersteunde beveiligingsalgoritmen:	WPA3, WPA, WPA2
Soort antenne:	Extern
Temperatuur bij opslag:	-40 - 70 °C
Luchtvochtigheid bij opslag:	5 - 93 procent
MIMO-type:	Multi User MIMO
Aansluiting antenne:	RP-SMA
Maximale overdrachtssnelheid van gegevens:	1774 Mbit/s
2,4 GHz:	Ja
5 GHz:	Ja
Auto MDI/MDI-X:	Ja
Power over Ethernet (PoE):	Ja
Aantal connectors:	2
Maximale overdrachtssnelheid van gegevens (2.4 GHz):	574 Mbit/s
Maximale overdrachtssnelheid van gegevens (5 GHz):	1200 Mbit/s
Bedrijfstemperatuur (T-T):	0 - 50 °C
Relatieve vochtigheid in bedrijf (V-V):	5 - 93 procent
Code geharmoniseerd systeem (HS):	85176990
Spread spectrum methode:	DSSS, OFDM, OFDMA