Aruba AP-535 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Aruba AP-535 (14 pagina's) in de categorie Access point. Deze handleiding was nuttig voor 56 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/14
Aruba 530 Series Campus Access Points
Installation Guide
Installation Guide | May 2019 1
Aruba 530 Series access points (AP-534 and AP-535) are high-performance, multi-radio wireless devices that can
be deployed in either controller-based (ArubaOS) or controllerless (InstantOS) network environments. These
access points deliver high-performance concurrent 2.4 GHz and 5 GHz 802.11ax Wi-Fi functionality with 4x4
MIMO radios, while also supporting legacy 802.11a/b/g/n/ac wireless services.
Ethernet ports located on the back of this access point are used to connect the device to the wired networking
infrastructure and to provide power over Ethernet (PoE) to the device (802.3at class 4 or 802.3bt class 5).
In addition to both Wi-Fi radios, these APs also incorporate a Bluetooth Low Energy (BLE) and Zigbee radio,
supporting a variety of use-cases and services, such as locationing and IoT.
A variety of mounting scenarios is supported by a range of mount kits (sold separately). Make sure to purchase
the correct mount kit for the intended deployment of the AP.
Hardware Overview
The following sections outline the hardware components of the 530 Series access point.
Figure 1 Aruba AP-535 (front view)
Figure 2 Aruba AP-534 (LEDs)
2Aruba 530 Series Campus Access Points | Installation Guide
External Antenna Connectors
The AP-534 access points are equipped with four external antenna connectors located on the front corners of
the access point (see Figure 2). Antenna ports A0 through A3 (corresponding with radio chains 0 through 3), are
used for both radios and bands (RF signals are diplexed).
LEDs
The LED displays located on the front panel of the access point indicate the following functions:
System Status
The System Status LED indicates the operating condition of the access point, See Table 1.
Table 1 System Status LEDs
1 Blinking: one second on/one second off, 2 second cycle.
2 Flashing Pattern 1: mostly on, briefly off, 2 second cycle.
3 Flashing Pattern 2: mostly off, briefly on, 2 second cycle.
Radio Status
The Radio Status LED indicates the operating mode of the access point’s radios. See Table 2.
!
!
!
!!
External antennas for this device must be installed by an Aruba Certified Mobility Professional (ACMP) or other
Aruba-certified technician, using manufacturer-approved antennas only.
The Equivalent Isotropically Radiated Power (EIRP) levels for all external antenna devices must not exceed the
regulatory limit set by the host country/domain.
Installers are required to record the antenna gain for this device in the system management software. A list of
approved antennas can be found at: http://www.arubanetworks.com/assets/og/OG_AP-530Series.pdf.
Les antennes externes pour cet appareil doivent être installées par un professionnel de la mobilité certifié Aruba
(ACMP) ou un autre technicien certifié Aruba, en utilisant uniquement des antennes approuvées par le fabricant.
Les niveaux équivalents de puissance à rayonnement isotrope (EIRP) pour tous les périphériques d'antenne
externe ne doivent pas dépasser la limite réglementaire définie par le pays hôte / domaine.
Les installateurs doivent enregistrer le gain d'antenne pour cet appareil dans le logiciel de gestion du système.
Une liste d'antennes approuvées peut être trouvée à http://www.arubanetworks.com/assets/og/OG_AP-
530Series.pdf.
Color/State Meaning
Off Device powered off
Green- blinking 1Device booting, not ready
Green- solid Device ready, fully functional, no network restrictions
Green- flashing pattern 12Device ready, fully functional, either uplink negotiated in sub-optimal speed
(<1Gbps)
Green- flashing pattern 23Deep sleep mode
Amber- solid Device ready, restricted power mode (limited PoE power available, or IPM
restrictions applied), no network restrictions
Amber- flashing pattern 1 Device ready, restricted power mode (limited PoE power available, or IPM
restrictions applied), uplink negotiated in sub-optimal speed (<1Gbps)
Red System error condition - Immediate attention required
Aruba 530 Series Campus Access Points | Installation Guide 3
Table 2 Radio Status LEDs
1 Alternating: one second each color, 2 second cycle.
LED Display Settings
The LEDs have three operating modes that can be selected in the system management software:
Default mode: Refer to Table 1 and Table 2
Off mode: LEDs are off
Blink mode: LEDs blink green
Force the LEDs into off mode and back to software defined mode by pressing the reset button for a short
duration. Warning: pressing the reset button for longer than 10 seconds may cause the AP to reset and return to
factory default state.
Figure 3 AP-535 access point (rear view)
External Antenna Connectors
The AP-534 access points are equipped with four external antenna connectors located on the front
corners of the access point (see Figure 4).
Color/State Meaning
Off AP powered off, or both radios disabled
Green- solid Both radios enabled in access mode
Green- blinking One radio enabled in access mode, other disabled
Amber- solid Both radios enabled in monitor mode
Amber- blinking One radio enabled in monitor mode, other disabled
Green/Amber-
alternating1Green: one radio in access mode
Amber: one radio in monitor mode


Product specificaties

Merk: Aruba
Categorie: Access point
Model: AP-535

Heb je hulp nodig?

Als je hulp nodig hebt met Aruba AP-535 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Access point Aruba

Handleiding Access point

Nieuwste handleidingen voor Access point

Vimar

Vimar 19195.B Handleiding

1 December 2024
Vimar

Vimar 20195.B Handleiding

1 December 2024
Vimar

Vimar 14195.SL Handleiding

1 December 2024
Vimar

Vimar 14195 Handleiding

1 December 2024
Vimar

Vimar 19195 Handleiding

1 December 2024
Vimar

Vimar 20195 Handleiding

1 December 2024
Vimar

Vimar 19195.M Handleiding

1 December 2024
Vimar

Vimar 20195.N Handleiding

1 December 2024
EQ-3

EQ-3 HMIP-HAP Handleiding

30 November 2024