Aruba AP-103H Handleiding

Aruba Access point AP-103H

Lees hieronder de 📖 handleiding in het Nederlandse voor Aruba AP-103H (2 pagina's) in de categorie Access point. Deze handleiding was nuttig voor 7 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Aruba AP-103H Wireless Access Point

The Aruba AP-103H wireless access point that supports the IEEE 802.11n

standard for high-performance WLAN. This access point uses MIMO (Multiple-

Input, Multiple-Output) technology and other high-throughput mode techniques

to deliver high-performance, 802.11n 2.4 GHz or 5 GHz functionality while

simultaneously supporting existing 802.11a/b/g wireless services. The AP-103H

access point works only in conjunction with an Aruba Controller.

The Aruba AP-103H access point provides the following capabilities:

Wireless transceiver

Protocol-independent networking functionality

IEEE 802.11a/b/g/n operation as a wireless access point

IEEE 802.11a/b/g/n operation as a wireless air monitor

Compatibility with IEEE 802.3af PoE

Central management configuration and upgrades through an Aruba

Controller

Package Contents

AP-103H Access Point

Single Gang Wall-box Mounting bracket

2x #6-32 Machine Screws

Security Key

Installation Guide (this document)

Hardware Overview

Figure 1 Front

LED

The AP-103H is equipped with one LED that indicates the system status of the

AP.

Figure 2 Rear

Console Port

The serial console port allows you to connect the AP to a serial terminal or a

laptop for direct local management. This port located at the rear of the AP-103H

is a 4-pin connector covered by a dust cover. An optional serial adapter cable

(AP-CBL-SER) is available for use with the AP-103H and is sold separately.

Figure 3 Bottom

Ethernet Ports

AP-103H is equipped with a total of three active Ethernet ports (ENET 0-2).

ENET 0 is a 10/100/1000Base-T (RJ-45) auto-sensing, MDI/MDX wired-network

uplink connectivity port. This port supports IEEE 802.3af Power over Ethernet

(PoE), accepting 48VDC as a standard defined Powered Device (PD) from a

Power Sourcing Equipment (PSE) such as a PoE midspan injector or network

infrastructure that supports PoE. ENET 1 and 2 are 10/100Base-T (RJ-45) auto-

sensing, MDI/MDX wired-network downlink connectivity ports, used to provide

secure network connectivity to wired devices. ENET 0 is located on the rear of

the AP, while ENET 1 and 2 are located on the bottom ( ).Figure 3

Additionally, AP-103H supports a passive pass-through RJ-45 interface to extend

a physical connection (typically another Ethernet connection) from the back of

the device to a connector on the bottom.

Figure 4 Gigabit Ethernet Port Pin-Out

Figure 5 Fast Ethernet Port Pin-Out

DC Power Socket

The AP-103H has a single 12V DC power jack socket to support powering

through an AC-to-DC power adapter.

Push Button

The push button can be used to reset the AP to factory default settings or turn

off/on the System Status LED.

To reset the AP to factory default settings:

1. Power off the AP.

2. Press and hold the push button using a small, narrow object, such as a

paperclip.

3. Power-on the AP without releasing the push button. The system status

LED will flash within 5 seconds.

4. Release the push button.

The system status LED will flash again within 15 seconds indicating that the

reset is completed. The AP will now continue to boot with the factory default

settings.

To turn off/on the system status LED:

During the normal operation of the AP, press the push button using a small,

narrow object, such as a paperclip. The system status LED will be turned off/

on immediately.

Before You Begin

Pre-Installation Network Requirements

After WLAN planning is complete and the appropriate products and their

placement have been determined, the Aruba controller(s) must be installed and

initial setup performed before the Aruba APs are deployed.

AP Pre-Installation Checklist

Before installing your AP-103H access point, be sure that you have the following:

Pre-installed wall box

Cat5 UTP cable with network access installed in the wall box

One of the following power sources:

IEEE 802.3af-compliant Power over Ethernet (PoE) source

Aruba AP AC-DC adapter kit (sold separately)

Aruba Controller provisioned on the network:

Layer 2/3 network connectivity to your access point

One of the following network services:

Aruba Discovery Protocol (ADP)

DNS server with an “A” record

DHCP Server with vendor-specific options

Summary of the Setup Process

Successful setup of an AP-103H access point consists of five tasks, which must

be performed in this order:

1. Verify pre-installation connectivity.

2. Identify the specific installation location for each AP.

3. Install each AP.

4. Verify post-installation connectivity.

5. Configure each AP.

Verifying Pre-Installation Connectivity

Before you install APs in a network environment, make sure that the APs are

able to locate and connect to the controller after power on. Specifically, you

must verify the following conditions:

When connected to the network, each AP is assigned a valid IP address

APs are able to locate the controller

Refer to the Guide for instructions on locating and ArubaOS Quick Start

connecting to the controller.

Identifying Specific Installation Locations

You can mount the AP-103H access point on a wall. Use the AP placement map

generated by Aruba’s RF Plan software application to determine the proper

installation location(s). Each location should be as close as possible to the

center of the intended coverage area and should be free from obstructions or

obvious sources of interference. These RF absorbers/reflectors/interference

sources will impact RF propagation and should have been accounted for during

the planning phase and adjusted for in RF plan.

Identifying Known RF Absorbers/Reflectors/Interference

Sources

Identifying known RF absorbers, reflectors, and interference sources while in

the field during the installation phase is critical. Make sure that these sources are

taken into consideration when you attach an AP to its fixed location.

RF absorbers include:

Cement/concrete—Old concrete has high levels of water dissipation, which

dries out the concrete, allowing for potential RF propagation. New concrete

has high levels of water concentration in the concrete, blocking RF signals.

Natural Items—Fish tanks, water fountains, ponds, and trees

Brick

RF reflectors include:

Metal Objects—Metal pans between floors, rebar, fire doors, air conditioning/

heating ducts, mesh windows, blinds, chain link fences (depending on

aperture size), refrigerators, racks, shelves, and filing cabinets.

Do not place an AP between two air conditioning/heating ducts. Make sure

that APs are placed below ducts to avoid RF disturbances.

RF interference sources include:

Microwave ovens and other 2.4 or 5 GHz objects (such as cordless phones)

Cordless headset such as those used in call centers or lunch rooms

Installing the AP

The AP-103H is designed to mount into a variety of electrical gang boxes.

1. Begin by removing the existing data wall plate (if applicable).

Figure 6 Removing Wall Plate (US Single Gang Outlet Box Shown)

2. Remove any existing RJ45 connectors (typically snap-in) or cut/remove the

UTP cable.

3. Use a short Ethernet cable (sold separately) to connect the ENET0 port to an

RJ45 connector or crimp an RJ45 plug (not supplied) on the cable and insert

in the ENET0 port. Do the same for the Pass Through port, if used.

4. Align the mounting holes of the AP-103H mounting bracket with mounting

holes in you gang box as shown in and . For worldwide Figure 7 Figure 8

single gang outlet box, the mounting bracket provides two sets of mounting

holes for fixing to the box to meet different installation position requirement.

See for details.Figure 8

The applicable standards for the wall boxes are:

IEC 60670-1, GB17466, BS4662 and DIN49073 for Worldwide

ANSI/NEMA OS 1 and OS 2 for US

5. Insert the two included machine screws and tighten them to secure the

mounting bracket.

The Aruba AP-103H requires ArubaOS 6.4.1 or later.

Inform your supplier if there are any incorrect, missing, or damaged

parts. If possible, retain the carton, including the original packing

materials. Use these materials to repack and return the unit to the

supplier if needed.

Table 1 LED Meanings

LED Color/State Meaning

System Status LED Off No power to AP, or LED switched to

‘off mode’

Red Error condition

Green - Flashing LED switched to ‘blink mode’

Green - Steady AP ready

Amber - Flashing AP booting, or AP in Air or Spectrum

monitor mode

Amber - Steady AP ready, restricted mode:

10/100Mbps uplink negotiated

Either radio in non-HT mode

For more information on blink and off mode of the LED, refer to the

ArubaOS User Guide.

AP-103H_01

System Status LED

Console Port

Pass Through

Port ENET0

Hot-plug operation is not recommended for the console port.

If both POE and DC power are available, the AP uses POE.

Power

Push Button ENET1 ENET2 Pass Through Port

FCC Statement: Improper termination of access points installed in

the United States configured to non-US model controllers will be in

violation of the FCC grant of equipment authorization. Any such willful

or intentional violation may result in a requirement by the FCC for

immediate termination of operation and may be subject to forfeiture

(47 CFR 1.80).

EU Statement:

Lower power radio LAN product operating in 2.4 GHz and 5 GHz

bands. Please refer to the for details on ArubaOS User Guide

restrictions.

Produit réseau local radio basse puissance operant dans la bande

fréquence 2.4 GHz et 5 GHz. Merci de vous referrer au ArubaOS User

Guide pour les details des restrictions.

Low Power FunkLAN Produkt, das im 2.4 GHz und im 5 GHz Band

arbeitet. Weitere Informationen bezlüglich Einschränkungen finden

Sie im ArubaOS User Guide.

Apparati Radio LAN a bassa Potenza, operanti a 2.4 GHz e 5 GHz.

Fare riferimento alla per avere informazioni ArubaOS User Guide

detagliate sulle restrizioni.

It is important that you verify the items listed under AP Pre-Installation

Checklist before you attempt to set up and install an AP-103H.

Aruba Networks, Inc., in compliance with governmental requirements, has

designed the AP-103H access points so that only authorized network

administrators can change the settings. For more information about AP

configuration, refer to the ArubaOS Quick Start Guide and ArubaOS User

Guide.

Access points are radio transmission devices and as such are subject to

governmental regulation. Network administrators responsible for the

configuration and operation of access points must comply with local

broadcast regulations. Specifically, access points must use channel

assignments appropriate to the location in which the access point will be

used.

The included machine screws may not fit all wall boxes.

Aruba AP-103H Wireless

Access Point

Installation Guide

www.arubanetworks.com

1344 Crossman Avenue

Sunnyvale, California 94089

Phone: 408.227.4500

Fax 408.227.4550

Aruba AP-103H Wireless Access Point | Installation Guide

Part Number 0511618-02 | July 2014

Contacting Aruba Networks

Web Support

Main Site http://www.arubanetworks.com

Support Site https://support.arubanetworks.com

Airheads Social Forums and Knowledge Base community.arubanetworks.com

North American Telephone 1-800-943-4526 (Toll Free)

1-408-754-1200

International Telephones arubanetworks.com/support-services/aruba-support-

program/contact-support/

Software Licensing Site licensing.arubanetworks.com/login.php

Wireless Security Incident

Response Team (WSIRT)

arubanetworks.com/support/wsirt.php

Support Email Addresses

Americas and APAC support@arubanetworks.com

EMEA emea.support@arubanetworks.com

Americas and APAC Support Email support@arubanetworks.com

WSIRT Email

Please email details of any security

problem found in an Aruba product.

wsirt@arubanetworks.com

For Wireless That Works®, Mobile Edge Architecture, People Move. Networks Must Follow., RFProtect

®, The All

Wireless Workplace Is Now Open For Business, and The Mobile Edge Company® are trademarks of Aruba

Open Source Code

Certain Aruba products include Open Source software code developed by third parties, including software code

subject to the GNU General Public License ("GPL"), GNU Lesser General Public License ("LGPL"), or other Open

Source Licenses. The Open Source code used can be found at this site:

http://www.arubanetworks.com/open_source

Legal Notice

The use of Aruba Networks, Inc. switching platforms and software, by all individuals or corporations, to terminate

other vendors' VPN client devices constitutes complete acceptance of liability by that individual or corporation for

this action and indemnifies, in full, Aruba Networks, Inc. from any and all legal actions that might be taken against

it with respect to infringement of copyright on behalf of those vendors.

Warranty

This hardware product is protected by the standard Aruba warranty of one year parts/labor. For more information,

refer to the ARUBACARE SERVICE AND SUPPORT TERMS AND CONDITIONS.

Altering this device (such as painting it) voids the warranty.

Figure 7 Bracket to Gang Box (US Single Gang Outlet Box Shown)

Figure 8 Bracket to Gang Box (Worldwide Single Gang Outlet Box Shown)

6. Connect any required cables to the rear of the AP-103H.

7. Align the mounting posts on the back of your AP-103H with the corresponding

mounting holes on the mounting bracket as shown in .Figure 9

8. Push the AP against the holes and downward until the posts engage the slots

at the top of the mounting holes. See and for more details.Figure 9 Figure 10

Figure 9 AP-103H to Bracket

Figure 10 Completed Installation

9. To remove the AP-103H from the mounting bracket, begin by inserting the

security key into the hole as shown in .Figure 11

10. Use the security key to depress the tab on the AP and push the AP up,

releasing the AP from the mounting holes on the bracket.

Figure 11 Removing the AP-103H

11. If not using PoE, connect the AC-DC power adapter (sold separately) to the

DC power socket located on the bottom of the AP-103H.

Verifying Post-Installation Connectivity

The integrated LED on the AP can be used to verify that the AP is receiving

power and initializing successfully (see ). Refer to the Table 1 ArubaOS Quick

Start Guide for further details on verifying post-installation network

connectivity.

Configuring the AP-103H

AP Provisioning/Reprovisioning

Provisioning parameters are unique to each AP. These local AP parameters are initially configured on

the controller which are then pushed out to the AP and stored on the AP itself. Aruba recommends

that provisioning settings be configured via the ArubaOS Web UI only. Refer to the ArubaOS User

Guide for complete details.

AP Configuration

Configuration parameters are network or controller specific and are configured and stored on the

controller. Network configuration settings are pushed out to the AP(s) but remain stored on the

controller.

Configuration settings can be configured via the ArubaOS Web UI or ArubaOS CLI. Refer to ArubaOS

User Guide for details.

Product Specifications

Electrical

Ethernet:

1 x 10/100/1000Base-T auto-sensing Ethernet RJ-45 Interface (ENET 0)

2 x 10/100Base-T auto-sensing Ethernet RJ-45 Interfaces (ENET 1 and ENET 2)

1 x passive RJ-45 pass-through interface

MDI/MDX

IEEE 802.3 (10Base-T), IEEE 802.3u (100Base-T). IEEE 802.3ab (1000Base-T)

Power over Ethernet (IEEE 802.3af compliant), 48V DC (nominal) and 56V DC (maximum)/

350mA (see for pin configuration)Figure 4

Power:

12 VDC power interface, supports powering through an AC-to-DC power adapter

POE support on Ethernet ports: 802.3af-compliant POE sourcing device

For additional specifications on this product, please refer to the data sheet. The data sheet can be

found at .www.arubanetworks.com

Proper Disposal of Aruba Equipment

For the most current information about Global Environmental Compliance and Aruba products, see

our website at .www.arubanetworks.com

Waste of Electrical and Electronic Equipment

Aruba products at end of life are subject to separate collection and treatment in

the EU Member States, Norway, and Switzerland and therefore are marked with

the symbol shown at the left (crossed-out wheelie bin). The treatment applied at

end of life of these products in these countries shall comply with the applicable

national laws of countries implementing Directive 2002/96EC on Waste of

Electrical and Electronic Equipment (WEEE).

India RoHS

This product complies with RoHS requirements as prescribed by E-Waste (Management & Handling)

Rules, governed by the Ministry of Environment & Forests, Government of India.

European Union RoHS

Aruba products also comply with the EU Restriction of Hazardous

Substances Directive 2011/65/EC (RoHS). EU RoHS restricts the use of

specific hazardous materials in the manufacture of electrical and

electronic equipment. Specifically, restricted materials under the RoHS

Directive are Lead (including Solder used in printed circuit assemblies), Cadmium, Mercury,

Hexavalent Chromium, and Bromine. Some Aruba products are subject to the exemptions listed in

RoHS Directive Annex 7 (Lead in solder used in printed circuit assemblies). Products and packaging

will be marked with the “RoHS” label shown at the left indicating conformance to this Directive.

China RoHS

Aruba products also comply with China environmental declaration requirements

and are labeled with the “EFUP 25” label shown at the left.

Safety and Regulatory Compliance

Aruba Networks provides a multi-language document that contains country-specific restrictions and

additional safety and regulatory information for all Aruba access points. This document can be

viewed or downloaded from the following location: www.arubanetworks.com/safety_addendum

Regulatory Model Names

The regulatory model name of AP-103H is APINH103.

FCC

This device is electronically labeled. To view the FCC ID:

1. Log into the controller WebUI.

2. Navigate to .Maintenance > Controller > About

EMC Compliance and Warning Statement

This equipment generates, uses and can radiate radio frequency energy, and, if not installed and used

in accordance with the manufacturer’s instructions may cause harmful interference to other devices

in the vicinity. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment causes interference with other devices, which may be determined by

turning the equipment off and on, the user is encouraged to try and correct the interference by one or

more of the following measures:

Reorient or relocate the device receiving the interference.

Increase the separation between the equipment.

Connect the equipment into an outlet on a circuit different from that to which the other device(s)

are connected.

Consult the manufacturer or field service technician for help.

The protection against electric shock is Class ll.

Equipment not suitable for use in the presence of flammable mixtures.

FCC Class B Part 15

This device complies with Part 15 of the Federal Communications Commission (FCC) Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause

undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the manufacturer’s instructions, may cause

interference harmful to radio communications.

If this equipment does cause interference, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment to an outlet on a circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio or TV technician for help.

Complies with the Class B limits for radio noise emissions as set out in the interference-causing

equipment standard entitled “Digital Apparatus,” ICES-003 of Industry Canada.

Cet apareil numerique de la classe B respecte toutes les exigencies du Reglement sur le materiel

brouilleur du Canada.

Users are advised that high power Radars are allocated as primary users of the bands 5250-5350 MHz

and 5650-5850 MHz and these Radars could cause interference and/or damage to Licensed Exempt

WLAN devices.

EU Regulatory Conformance

This product is CE marked according to the provisions of the R & TTE Directive

(1999/5/EC) - CE(!). Aruba Networks Inc., hereby declares that the APIN0103 device

model is in compliance with the essential requirements and other relevant provisions of Directive

1999/5/EC -CE(!)

The Declaration of Conformity made under Directive 1999/5/EC is available for viewing at the

following location: http://support.arubanetworks.com

Users are advised that high power Radars are allocated as primary users of the bands 5250-5350 MHz

and 5650-5850 MHz and these Radars could cause interference and/or damage to Licensed Exempt

WLAN devices.

Canadian Statement

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a

type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce

potential radio interference to other users, the antenna type and its gain should be so chosen that the

equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful

communication.

This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired

operation of the device.

AP-103H_04

AP-103H_07

Another

two

mounting

holes

AP-103H_05

AP-103H_06

If a power adapter other than the one provided by Aruba Networks is used

in the US or Canada, it should be NRTL Listed, with an output rated 12

VDC, minimum 1.25A, marked “LPS” and “Class 2”, and suitable for

plugging into a standard power receptacle in the US and Canada.

Aruba access points must be installed by a professional installer. The

professional installer is responsible for ensuring that grounding is available

and it meets applicable local and national electrical codes.

RF Radiation Exposure Statement: This equipment complies with FCC

RF radiation exposure limits. This equipment should be installed and

operated with a minimum distance of 7.87 inches (20cm) between the

radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter

must not be co-located or operating in conjunction with any other antenna

or transmitter. When operated in the 5.15 to 5.25 GHz frequency range, this

device is restricted to indoor use.

Changes or modifications to this unit not expressly approved by the party

responsible for compliance could void the user’s authority to operate this

equipment.

Product specificaties

Merk:	Aruba
Categorie:	Access point
Model:	AP-103H

Heb je hulp nodig?

Als je hulp nodig hebt met Aruba AP-103H stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Access point Aruba

Aruba AP-504 Handleiding

20 Augustus 2024

Aruba AP-318 Handleiding

19 December 2023

Aruba AP-577 Handleiding

19 December 2023

Aruba Instant IAP-175 Handleiding

30 Mei 2023

Aruba 205H Handleiding

25 Mei 2023

Aruba AP-93H Handleiding

25 Mei 2023

Aruba AP-503H Handleiding

8 Mei 2023

Aruba AP-567 Handleiding

7 Mei 2023

Aruba Instant IAP-175P Handleiding

29 April 2023

Aruba AP-375EX Handleiding

23 April 2023

Handleiding Access point

Nieuwste handleidingen voor Access point

TP Link Festa F65-Outdoor Handleiding

11 December 2024

Mikrotik WAP R Handleiding

8 December 2024

Mikrotik Wireless Wire Handleiding

8 December 2024

TP Link RE6000XD Handleiding

3 December 2024

Vimar 19195.B Handleiding

1 December 2024

Vimar 20195.B Handleiding

1 December 2024

Vimar 14195.SL Handleiding

1 December 2024

Vimar 14195 Handleiding

1 December 2024

Vimar 19195 Handleiding

1 December 2024

Vimar 20195 Handleiding

1 December 2024