Apc Smart-UPS SUA24XLBP Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Apc Smart-UPS SUA24XLBP (2 pagina's) in de categorie UPS. Deze handleiding was nuttig voor 52 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/2
Smart-UPS® External Battery Pack SUA24XLBP
990-5054 04/2011
Refer to the User Manual for basic information about the Smart-UPS and the Smart-UPS XL Supplement for additional information on extended run versions of the
UPS. This supplement provides information on the battery packs.
Installation
Inspection
Inspect the battery pack upon receipt. Notify the carrier and dealer if there is damage. The packaging is recyclable; save it for reuse or dispose of it properly.
Placement
This figure shows the location of the battery pack connector.
The battery pack connector is color coded and keyed to prevent improper connection. Do not attempt to
install battery packs with connectors that are a different color from the battery pack connector on the UPS.
Install up to 10 battery packs per XL model UPS following the instructions below.
1. Prepare the UPS to connect the battery pack(s).
Note the holes used to attach the battery pack
connector clamp (near the center of the
connector opening). Use a #2 Phillips head
screwdriver to remove the battery pack
connector clamp from the back of the UPS.
3. Holding the clamp aside, insert the battery pack connector into
the UPS.
2. Turn the clamp over and loosely attach one end
at the edge of the connector opening in the
UPS.
4. Secure the connector clamp.
For additional battery packs, repeat this procedure using the battery pack connectors on the battery packs.
Note: Do not stack battery packs. Stacking results in a tipping hazard.
Storage
Storage Conditions
Store the battery pack covered and upright in a cool, dry location, with its
batteries fully charged. Before storing, charge the battery pack for at least
4 hours.
Extended Storage
At -15 to +30 °C (+5 to +86 °F), charge the battery pack every 6 months
At +30 to +45 °C (+86 to +113 °F), charge the battery pack every 3 months.
Battery Charge and Run Times
A floppy disk is shipped with each battery pack to configure your Smart-UPS for use with each new battery pack added. Your Smart-UPS needs to be configured
appropriately so that it can better calculate the discharge time. Connect the UPS’ port to a serial port on a PC or workstation running DOS or Windows, by using the
black colored communications cable included. Next, while at the DOS prompt, insert the floppy disk into a drive and change to that drive’s letter (e.g.. A:) Then
type: battpack com[X] [Y], where [X] = 1 or 2 depending on the serial port used, and [Y] = number of battery packs attached to the UPS.
The Smart-UPS XL Supplement contains tables showing both the time required for charging UPS and battery pack batteries for rated protection and typical run
times.
Replacing the Battery
This battery pack has easy to replace hot-swappable batteries. Battery replacement is a safe procedure, isolated from electrical hazards. You may leave the UPS and
loads on for the following procedure. See your dealer or call the number in this manual for information on replacement battery kits.
Note: Please read the cautions in the APC Safety Guide. Save your data before beginning this procedure. Once the battery is disconnected, the loads are
not protected from power outages.
Battery Replacement Procedure - Rack Mount XL Battery Packs
1.Reach into the finger pull and remove the front cover.
2.Use a flat-blade, screwdriver or coin to remove the battery
door screws and open the door.
Warning! Do not force the battery out. This may
damage internal wiring!
3.Disconnect the battery connector by pulling on the white
cord on the side of the battery.
4.Slide the battery out of the battery pack.
5.Remove the foam separator.
6.Repeat steps 3 - 5 for the second battery.
7.Repeat steps 3 - 6 for the two batteries on the other side of
the battery pack.
Note: Be careful removing the batteries - they are heavy..
8.Slide the new battery into the battery pack.
9.Connect the battery connector
Note: Small sparks at the battery connectors are normal
during connection.
10.Push the battery in as far as it will go. There are stops in
the back to prevent it from going too far.
11.Replace the foam separator.
12.Repeat steps 8 - 10 for the second battery.
13.Repeat steps 8 - 12 for the two batteries on the other side
of the battery pack.
14.Close the battery door, replace the battery compartment
screws, and replace the front cover.
15.Dispose of the old battery properly at an appropriate
recycling facility or return it to the supplier in the packing
material for the new battery. See the new battery
instructions for more information.
Specifications
Typical Battery Life 3 to 6 years, depending on number of discharge
cycles and ambient temperature
Operating Temperature 0 to 40°C (+32 to +104°F)
Storage Temperature -15 to 45°C (+5 to _113°F)
Operating and Storage
Relative Humidity
0 to 95%, non-condensing
Operating Elevation 0 to +3,000 m (0 to +10,000 ft.)
Storage Elevation 0 to +15,000 m (0 to +50,000 ft.)
Size (H x W x D) Tower:
21.6 x 17.0 x 43.9 cm
(8.5 x 6.7 x 17.3 in.)
Rack Mount:
17.8 x 48.3 x 45.7 cm
(7.0 x 19.0 x 18.0 in.)
Weight - net (shipping) 31.3 (33.1) kg
69.0 (73.0) lb.
61.7 (69.4) kg
136.0 (153.0) lb.
©2011 APC by Schneider Electric. APC, the APC logo, Smart-UPS and
PowerChute are owned by Schneider Electric Industries S.A.S., American
Power Conversion Corporation, or their affiliated companies. All other
trademarks are property of their respective owners.
Battery Replacement Procedure - Tower XL Battery Packs
1.Grasp the side of the front cover and tilt it out and down.
2.Unhook the bottom of the cover from the chassis and
remove it to expose the battery door
3.Use a flat-blade screwdriver or a coin to remove the two
battery door screws and open the door.
4.Pull the white cord on the front battery connector to remove
the battery connector.
5.Grasp the tab and gently pull the battery out of the battery
pack.
6.Reach into the battery compartment and grasp the white
cord on the other battery connector. Pull firmly to
disconnect the connector and remove the second set of
batteries.
Note: Be careful removing the batteries - they are heavy..
7.Slide the first set of new batteries into the unit. Hold the
connector down below the top of the batteries and toward the
door, otherwise the assembly will not fit. Guide the
connector over the top of the batteries and press firmly to
connect it to the rear connector of the battery compartment.
Note: Small sparks at the battery connectors are normal
during connection.
8. Slide the second set of batteries in, then guide the connector
over the batteries and press firmly to connect it to the front
connector of the battery compartment.
9.Now close the battery door, replace the screws, and replace
the front cover.
10.Dispose of the old battery properly at an appropriate
recycling facility or return it to the supplier in the packing
material for the new battery. See the new battery instructions
for more information.
APC Customer Support and Warranty
APC Web site: www.apc.com/jp
Telephone: 03-6402-2030
Limited Warranty
APC® by Schneider Electric warrants its products to be free from defects in materials
and workmanship for a period of six months from the date of purchase. Its obligation
under this warranty is limited to repairing or replacing, at its own sole
option, any such defective products. To obtain service under warranty you must obtain a
Returned Material Authorization (RMA) number from customer support. Products must
be returned with transportation charges prepaid and must be
accompanied by a brief description of the problem encountered and proof of date and
place of purchase. This warranty does not apply to equipment that has been damaged by
accident, negligence, or misapplication or has been altered or modified in any way. This
warranty applies only to the original purchaser who must have properly registered the
product within 10 days of purchase.
EXCEPT AS PROVIDED HEREIN, AMERICAN POWER CONVERSION MAKES
NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Some states
do not permit limitation or exclusion of implied warranties; therefore, the aforesaid
limitation(s) or exclusion(s) may not apply to the purchaser.
EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL APC BE LIABLE FOR
DIRECT, INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF
THIS PRODUCT, EVEN IF
ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Specifically, APC is not
liable for any costs, such as lost profits or revenue, loss of equipment, loss of use of
equipment, loss of software, loss of data, costs of substitutes, claims by third parties, or
otherwise.
Product specificaties
| Merk: | Apc |
| Categorie: | UPS |
| Model: | Smart-UPS SUA24XLBP |
Heb je hulp nodig?
Als je hulp nodig hebt met Apc Smart-UPS SUA24XLBP stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding UPS Apc
2 December 2024
2 December 2024
2 December 2024
2 December 2024
16 November 2024
12 November 2024
12 Oktober 2024
12 Oktober 2024
12 Oktober 2024
12 Oktober 2024
Handleiding UPS
- UPS HP
- UPS IKEA
- UPS AEG
- UPS Siemens
- UPS Dell
- UPS Digitus
- UPS Eaton
- UPS Emerson
- UPS Furman
- UPS Gembird
- UPS Gys
- UPS Lenovo
- UPS LevelOne
- UPS Riello
- UPS Schneider
- UPS Voltcraft
- UPS Jung
- UPS Steren
- UPS Conceptronic
- UPS Tripp Lite
- UPS Approx
- UPS Block
- UPS LC-Power
- UPS Energenie
- UPS CyberPower
- UPS Adj
- UPS East
- UPS Equip
- UPS Liebert
- UPS Avocent
- UPS Minute Man
- UPS Minuteman
- UPS Maruson
- UPS V7
- UPS Phoenix Contact
- UPS Puls Dimension
- UPS Vanson
- UPS Salicru
- UPS SurgeX
- UPS Murr Elektronik
- UPS Altronix
- UPS Ditek
- UPS Bxterra
- UPS Middle Atlantic
- UPS FSP
- UPS Atlantis Land
- UPS PowerWalker
- UPS FSP/Fortron
- UPS Online USV
Nieuwste handleidingen voor UPS
14 December 2024
14 December 2024
10 December 2024
10 December 2024
8 December 2024
8 December 2024
18 November 2024
17 November 2024
17 November 2024
17 November 2024