Apc Back-UPS 750VA Handleiding

Apc UPS Back-UPS 750VA

Lees hieronder de 📖 handleiding in het Nederlandse voor Apc Back-UPS 750VA (8 pagina's) in de categorie UPS. Deze handleiding was nuttig voor 96 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

Installation and Operation

Back-UPS® BE750G Series

Safety

Specifications

This unit is intended for indoor use only.

Do not operate this unit in direct sunlight, in contact with fluids, or where there

is excessive dust or humidity.

Connect the Back-UPS power cord directly to a wall outlet. Do not use a surge

protector or an extension cord.

Input

Voltage 120 Vac Nominal

Frequency 50 Hz/60 Hz auto sensing

Brownout Transfers 92 Vrms Typical

Over-voltage Transfer 139 Vrms Typical

Output

UPS Capacity

(5 battery backup outlets) 750 VA, 450 W

Total Amperage (all outlets) 12 A (including UPS output)

Voltage - On Battery 115 Vrms ± 8% step approximated sine wave

Frequency - On Battery 50 Hz/60 Hz ± 1 Hz

Transfer Time 6 ms Typical, 10 ms maximum

Protection and

Filtering

AC Surge Protection Full time, 354 Joules

Phone/DSL/FAX surge protection Single line (2 wire)

Cable/CAT V/DSS surge protection One coax input/output

Network surge protection 10/100 Base -T ethernet

EMI/RFI Filter Full time

AC Input Resettable circuit breaker

Battery

Type Sealed, maintenance-free, lead acid

Replacement battery cartridge RBC17

Average Life 3 - 5 years depending on the number of discharge cycles and

environmental temperature

Physical

Net Weight 11 lb (5 kg)

Dimensions

Length x Width x Height 14 in x 7 in x 4 in

36 cm x 18 cm x 9 cm

Operating Temperature 32º F to 104º F (0º C to 40º C)

Storage Temperature 5º F to 113º F (–15º C to 45º C)

Operating Relative Humidity 0 to 95% non-condensing humidity

Operating Elevation 0 to 10,000 ft (0 to 3000 m)

EMC

Compliance

This device complies with part 68 and part 15 of the FCC rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) This device must accept any

interference received, including interference that may cause undesired operation.

Back-UPS BE750G Series2

Connect the Battery

The Back-UPS is shipped with one battery cable disconnected. Remove the “Stop! Connect the Battery” label that

covers the outlets. Prior to connecting any equipment to the unit, connect the battery cable to the unused battery

terminal. It is normal for small sparks to be seen when the battery cable is connected to the battery terminal.

Wall Mount Installation

• Horizontal installation, use 2 screws 5.9" (150 mm) apart.

• Vertical installation, use 2 screws 5.5" (140 mm) apart.

• Allow 5/16" (8 mm), of the screw to protrude from the wall.

Connect Equipment

Battery Backup + Surge Protection Outlets

Battery backup outlets provide protection to connected

equipment when the Back-UPS is turned on and

connected to utility power.

Battery backup outlets receive power from the

Back-UPS for a limited period of time when a power

outage, or brownout condition occurs.

Battery backup outlets provide protection from power

surges or spikes.

Connect a computer, monitor and other peripheral devices to the outlets.

Surge Protection Outlets

Surge protection outlets provide protection to connected equipment when the Back-UPS is connected to utility

power, and is switched on or off.

Surge protection outlets provide protection from power surges or spikes.

Connect a printer, scanner or other peripheral devices to the surge protection outlets.

 Press the battery compartment cover

release tab located on the rear side of the

unit. Slide the battery cover off.

 Connect the battery cable securely

to the battery terminal.

 Reinstall the battery compartment

cover. Be sure that the release tab

locks into place.

bu076a

bu077a

bu083a

bu207a

Back-UPS

Ma st er

Enable

Battery Backup + Surge Protection

MASTER

Surge Protection

Controlled By MASTER

Back-UPS BE750G Series 3

Connect Modem/Telephone/DSL/FAX/10/100

Base-T Network Cable

The Back-UPS protects a single line, 2 wire telephone

line, including a Digital Subscriber Line (DSL), a

modem, a 10/100 Base-T ethernet, or a FAX machine

from power surges when connected through the

Back-UPS coaxial connectors.

PowerChute® Personal Edition Software

Overview

PowerChute Personal Edition Software allows you to use your computer to access additional power protection and

management features of the Back-UPS.

Using PowerChute, you can:

• Preserve work in progress during a power outage by putting your computer into Hibernate mode.

When the power returns, the computer will appear exactly as it did before the power outage.

• Conﬁgure the Back-UPS management features, such as power-saving outlets, shutdown

parameters, audible alarms, and more.

• Monitor and view the status of the Back-UPS, including the estimated runtime, power

consumption, power event history, and more.

Available features will vary by Back-UPS model and operating system.

If you choose not to install PowerChute, the Back-UPS will still provide backup power and power protection to

connected equipment. However, you will only be able to configure a limited number of features using the display

interface.

Compatibility

PowerChute is compatible with Windows operating systems only. For a detailed list of supported operating

systems, go to www.apc.com, select Software & Firmware.

For Mac operating systems, we recommend using the native shutdown application (within System Preferences)

which recognizes your battery backup and allows you to configure shutdown of your system during power outages.

To access this application, connect a USB cable from the Back-UPS DATA PORT (POWERCHUTE PORT) to a USB

port on your computer, and see the documentation provided with your computer.

Installation

Connect the Back-UPS to a computer using a USB cable. Plug one end into the P COWER HUTE PORT on the rear

panel of the Back-UPS and the other into a USB port on your computer.

Insert the PowerChute CD into your computer and follow the on-screen instructions. If your Back-UPS did not

come with a PowerChute CD, download the software from www.apc.com, select Software & Firmware.

bu209a

CAUTION-Ref er to bottom

of unit for safety markings.

Building

Wiring Fault

PowerChute

USB Port

Circuit Breaker

Push to Reset

Cable In Cable Out

Out

Network/DSL/Modem/FAX

Product specificaties

Merk:	Apc
Categorie:	UPS
Model:	Back-UPS 750VA
Kleur van het product:	Zwart
Gewicht:	4700 g
Breedte:	180 mm
Diepte:	343 mm
Hoogte:	88 mm
Snoerlengte:	1.83 m
Geluidsniveau:	45 dB
LED-indicatoren:	Batterijvervanging
Vormfactor:	Compact
Aantal Ethernet LAN (RJ-45)-poorten:	3
Certificering:	FCC, NOM, UL
Duurzaamheidscertificaten:	RoHS
Uitgangsvermogen:	450 W
Accu/Batterij oplaadtijd:	16 uur
Temperatuur bij opslag:	-15 - 45 °C
Frequentie:	50/60 Hz
Luchtvochtigheid bij opslag:	5 - 95 procent
Netwerkfuncties:	Fast Ethernet
Filtratie:	Ja
Hoogte, in bedrijf:	0 - 3000 m
Hoogte bij opslag:	0 - 15000 m
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	5 - 95 procent
Batterijtechnologie:	Sealed Lead Acid (VRLA)
Type batterij:	RBC17
Surge energy rating:	354 J
Aantal AC uitgangen:	10 AC-uitgang(en)
Nominale input voltage:	120 V
Stopcontacttypes:	NEMA 5–15R
Golf protectie functies:	A/V, Coax, Fax, Modem, Network, Telephone
Output power capacity:	0.75 kVA
Ingang operation voltage (min):	- V
Ingang operation voltage (max):	- V
Uitgang operation voltage (min):	- V
Uitgang operation voltage (max):	- V
Netspanning, in bedrijf:	120 V
Spanningsbeveiliging:	Ja