Apc Back-UPS 550 Handleiding

Apc UPS Back-UPS 550

Lees hieronder de 📖 handleiding in het Nederlandse voor Apc Back-UPS 550 (2 pagina's) in de categorie UPS. Deze handleiding was nuttig voor 73 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Safety

Specifications

Connect the Battery

The Back-UPS is shipped with one battery cable disconnected. Remove the “Stop!

Connect the Battery” label that covers the outlets. Prior to connecting any equipment

to the unit, connect the battery cable to the unused battery terminal. It is normal for

small sparks to be seen when the battery cable is connected to the battery terminal.

Wall Mount Installation

• Horizontal installation, use 2 screws 7.3" (186.3 mm) apart.

• Vertical installation, use 2 screws 5.4" (137.2 mm) apart.

• Allow 5/16" (8 mm), of the screw to protrude from the wall.

Replace Battery

Use only approved APC replacement battery cartridges.

Deliver used batteries to a battery replacement facility in the packaging provided by

APC with the replacement battery cartridge. To order replacement battery cartridges

contact APC.

Connect Equipment

Battery Backup + Surge Protection Outlets

Battery backup outlets provide protection to connected equipment when the

Back-UPS is turned on and connected to utility power.

Battery backup outlets receive power from the Back-UPS for a limited period of time

when a power outage, or brownout condition occurs.

Battery backup outlets provide protection from power surges or spikes.

Connect a computer, monitor and other peripheral devices to the outlets.

Surge Protection Outlets

Surge protection outlets provide protection to connected equipment when the

Back-UPS is connected to utility power, and is switched on or off.

Surge protection outlets provide protection from power surges or spikes.

Connect a printer, scanner or other peripheral devices that do not need to remain on

during power outages, or utility problems to the surge protection outlets.

Connect Network

The Back-UPS protects equipment connected to a 10/100 Base-T ethernet, from

power surges when connected through the Back-UPS coaxial connectors.

PowerChute® Personal Edition Software

Overview

Use PowerChute Personal Edition software to configure the UPS settings.

Protect your computer and other equipment during a power outage. During a power

outage, PowerChute will save any open files on your computer and safely shut it

down. When power is restored, it will restart the computer.

Configure the UPS to use features such as power-saving outlets, shutdown

configuration, and alarms.

Monitor the UPS for power usage and power events.

Note: PowerChute is only compatible with a Windows operating system. If you are

using a Mac OSX, use the native shutdown feature to protect your system. See the

documentation provided with your computer.

Installation

Use a USB cable to connect the Data port on the rear panel of the UPS to the USB port

on your computer.

If the Back-UPS came with CD into your computer and a PowerChute CD, insert the

follow the on-screen instructions

If the Back-UPS did not come with a PowerChute CD, go to www.apc.com and

download the software free of charge.

Turn On the Back-UPS

Press the POWER ON button located on the top of the Back-UPS. The Power On/

Replace Battery LED will illuminate and a single short beep will be audible to

indicate that the Back-UPS is providing protection for connected equipment.

The Back-UPS battery charges fully during the first 16 hours while connected to

utility power. The Back-UPS battery will charge while the Back-UPS is switched on

or off and is connected to utility power. Do not expect full battery run capability

during the initial charge time.

If the red Building Wiring Fault LED located on the side of the Back-UPS

illuminates, do not operate the Back-UPS. Have a qualified electrician correct the

building wiring fault.

Warranty

The standard warranty is 3 years in the USA and Canada, 2 years in all other regions

from the date of purchase. APC standard procedure is to replace the original unit with

a factory reconditioned unit. Customers who must have the original unit back due to

assigned asset tags and set depreciation schedules must declare such a need at first

contact with APC Technical Support. APC will ship the replacement unit once the

defective unit is received by the repair department or cross-ship upon the provision of

a valid credit card number. The customer pays for shipping to APC, and APC pays

ground freight transportation costs back to the customer.

This unit is intended for indoor use only.

Do not operate this unit in direct sunlight, in

contact with fluids, or where there is excessive

dust or humidity.

Connect the Back-UPS power cord directly to a

wall outlet. Do not use a surge protector or an

extension cord.

Input

Voltage 120 Vac Nominal

Frequency 60 Hz + 3

Brownout Transfers 92 Vac Typical

Over-voltage Transfer 139 Vac Typical

Output

UPS Capacity

(4 battery backup outlets) BE450G: 450 VA, 257 W;

BE550G: 550 VA, 330 W;

BE650G1: 650 VA, 390 W

Total Amperage (all outlets) 12 A (including UPS output)

Voltage - On Battery 115 Vac ± 8%

Frequency - On Battery 60 Hz + 1

Transfer Time 6 ms Typical, 10 ms maximum

Protection

and

Filtering

AC Surge Protection Full time, 340 Joules

EMI/RFI Filter Full time

AC Input Resettable circuit breaker

Battery

Type Sealed, maintenance-free, lead acid

BE450G: RBC114

BE550G: RBC110

BE650G1: RBC17

Average Life 3 - 5 years depending on the number of

discharge cycles and environmental

temperature

Physical

Net Weight Replacement battery cartridge

BE450G: 10 lb (4.7 kg)

BE550G: 12 lb (5.5 kg)

BE650G1: 14 lb (6.2 kg)

Dimensions

Length x Width x Height 12 in x 7 in x 3 in

30 cm x 18 cm x 9 cm

Operating Temperature 32º F to 104º F (0º C to 40º C)

Storage Temperature 5º F to 113º F (–15º C to 45º C)

Operating Relative Humidity 0 to 95% non-condensing humidity

Operating Elevation 0 to 10,000 ft (0 to 3000 m)

EMC

Compliance

This device complies with part 68 and part 15 of the FCC rules.

Operation is subject to the following two conditions: (1) This device

may not cause harmful interference, and (2) This device must accept any

interference received, including interference that may cause undesired

operation.

 Press the battery compartment cover

release tab located on the rear side of the

unit. Slide the battery cover off.

 Connect the battery cable securely to the

battery terminal.

 Reinstall the battery compartment cover.

Be sure that the release tab locks into place.

bu064a

bu065a

bu066a

bu202a

Back-UPS

Battery Backup + Surge Protection

Surge Protection

bu201a

CAUTION-Refer to bottom

of unit for safety markings.

Circuit

Breaker

Building

Wiring Fault

PowerChute

USB Port

Network

Out

Push to

Reset

Network

User Manual Back-UPS® BE 450G/550G/650G1

990-3951B

7/2011

or their affiliated companies. All other trademarks are property of their respective owners.

Status Indicators

Troubleshooting Voltage Sensitivity Adjustment (optional)

The Back-UPS detects and reacts to line voltage distortions by transferring to battery

backup power to protect connected equipment. In situations where either the Back-UPS

or the connected equipment is too sensitive for the input voltage level it is necessary to

adjust the transfer voltage.

1. Connect the Back-UPS to a wall outlet. The Back-UPS will be in Standby mode, no

indicators will be illuminated.

2. Press and hold the ON/OFF button for 10 seconds. The OnLine LED will

illuminate alternately green-amber-red, to indicate that the Back-UPS is in

Program mode.

3. The Power On/Replace Battery LED will ﬂash either green, amber, or red to

indicate the current sensitivity level. Refer to the table for an explanation of the

transfer voltage sensitivity levels.

4. To select LOW sensitivity, press and hold the ON/OFF button until the LED flashes

green.

5. To select MEDIUM sensitivity, press and hold the ON/OFF button until the LED

flashes red.

6. To select HIGH sensitivity, press and hold the ON/OFF button until the LED flashes

amber.

7. To exit Program mode wait five seconds and all LED indicators will extinguish.

Program mode is no longer active.

Service

If the unit requires service, do not return it to the dealer. Follow these steps:

1. Review the Troubleshooting section of the manual to eliminate common problems.

2. If the problem persists, contact APC Customer Support.

a. Note the model number and serial number and the date of purchase. The model

and serial numbers are located on the rear panel of the unit and are available

through the LCD display on select models.

b. Call APC Customer Support and a technician will attempt to solve the problem

over the phone. If this is not possible, the technician will issue a Returned

Material Authorization Number (RMA#).

c. If the unit is under warranty, the repairs are free.

d. Service procedures and returns may vary internationally. Refer to the APC Web

site for country speciﬁc instructions.

3. Pack the unit properly to avoid damage in transit. Never use foam beads for

packaging. Damage sustained in transit is not covered under warranty. Always

DISCONNECT THE UPS BATTERY before shipping in compliance with U.S.

Department of Transportation (DOT) and IATA regulations. The battery may

remain in the unit.

4. Write the RMA# provided by Customer Support on the outside of the package.

5. Return the unit by insured, pre-paid carrier to the address provided by

Customer Support.

Contact

APC Web site, www.apc.com

Status LED Indicator Audible Indicator On Audible Indicator Terminates

Power On

The Back-UPS is supplying utility power to connected equipment. The green LED illuminates. None N/A

On Battery

Back-UPS supplying battery power to battery backup outlets.

The green LED illuminates. The LED

is not illuminated during the beeps. Back-UPS beeps 4

times every 30 seconds. Beeping stops when utility power is restored or

the Back-UPS is turned off.

Low Battery warning

The Back-UPS is supplying battery power to the battery backup outlets

and the battery is near a total discharge state.

The green LED illuminates with rapid

green flashes.

The Back-UPS emits

rapid beeping, every

1/2 second.

Beeping stops when utility power is restored or

the Back-UPS is turned off.

Replace Battery

• The battery is disconnected.

• The battery needs to be charged, or replaced.

•Replace Battery LED flashes.

• Replace Battery and Power On

LEDs flash alternately.

Constant tone

Constant tone Back-UPS is turned off.

Overload Shutdown

While on battery power an overload condition has occurred in one or

more of the battery backup outlets while the Back-UPS is operating on

battery power.

None Constant tone Back-UPS is turned off.

Sleep Mode

While on battery power the battery is completely discharged. The

Back-UPS will “awaken” once utility power is restored. None

The Back-UPS beeps

once every four

seconds.

The beeping stops when:

• Utility power is restored

• If utility power is not restored within 32 seconds

• The Back-UPS is turned off

Building Wiring Fault

The building wiring presents a shock hazard that must be corrected by a

qualified electrical.

Building Wiring Fault LED

illuminates red

None The Back-UPS is unplugged from the wall outlet

or is plugged into an improperly wired outlet.

Problem and Possible Cause Solution

The Back-UPS will not turn on

The Back-UPS has not been turned

on. Press the POWER ON button.

The Back-UPS is not connected to

utility power, there is no utility power

available at the wall outlet, or the

utility power is experiencing a

brownout or over voltage condition.

Make sure the power cord is securely connected to

the wall outlet, and that there is utility power

available at the wall outlet.Where applicable,

check that the wall outlet is switched on.

The battery is not connected. Connect the battery. Refer to “Connect the

Battery” on page 1 of this manual.

In the event that the Back-UPS receives no utility

power and the battery is connected, a cold-start can

be initiated. Press and hold the Power On button

until the Back-UPS emits two beeps.

The Back-UPS is on, the Replace Battery LED flashes and the unit emits a

constant tone

The battery is disconnected. Refer to the “Connect the Battery” on page 1.

Connected equipment loses power

A Back-UPS overload condition has

occurred.

Remove all nonessential equipment connected to

the outlets. One at a time reconnect equipment to

the Back-UPS.

The Back-UPS battery is completely

discharged.

Connect the Back-UPS to utility power and allow

the battery to recharge for eight hours.

PowerChute software has performed a

shutdown due to a power failure.

This is normal Back-UPS operation.

Connected equipment does not accept

the step-approximated sine waveform

from the Back-UPS.

The output waveform is intended for computers

and peripheral devices. It is not intended for use

with motor driven equipment.

The Back-UPS may require service. Contact APC Technical Support for more in depth

troubleshooting.

The Power On LED is illuminated and the Back-UPS beeps 4 times every 30

seconds

The Back-UPS is operating on battery

power.

The Back-UPS is operating normally on battery

power. At this point the user should save all open

files, and shutdown the computer. When utility

power is restored the battery will recharge.

The Power On LED flashes once every second while the Back-UPS beeps once

every second

The Back-UPS battery has

approximately two minutes of

remaining runtime.

The Back-UPS battery is near a total discharge

state. At this point the user should save all open

files, and shutdown the computer. When utility

power is restored the battery will recharge.

The Building Wiring Fault LED illuminates

The building wiring presents a shock

hazard that must be corrected by a

qualified electrical.

Do not operate the Back-UPS. Call a qualified

electrician to correct the building wiring fault.

The Back-UPS has an inadequate battery runtime

The battery is not fully charged.

The battery is near the end of useful

life and should be replaced.

Leave the Back-UPS connected to utility power for

16 hours while the battery charges to full capacity.

As a battery ages, the runtime capability decreases.

Contact APC at the Web site www.apc.com, to

order replacement batteries.

The connection from the Back-UPS to the internet is lost during a power

outage

The modem has lost power. Connect the modem cable into one of the Battery

Backup + Surge Protection outlets.

LED

Flashes

Sensitivity

Setting

Input Voltage Range

(Utility Operation) Recommended Use

Green LOW 88 Vac to 142 Vac Use this setting with equipment that is less

sensitive to fluctuations in voltage or

waveform distortions.

Red MEDIUM 92 Vac to 139 Vac Factory default setting. Use this setting

under normal conditions.

Amber HIGH 96 Vac to 136 Vac Use this setting when connected equipment

is sensitive to voltage and waveform

fluctuations.

Product specificaties

Merk:	Apc
Categorie:	UPS
Model:	Back-UPS 550
Kleur van het product:	Zwart
Gewicht:	6020 g
Breedte:	224 mm
Diepte:	311 mm
Hoogte:	89 mm
Snoerlengte:	1.83 m
Geluidsniveau:	40 dB
Gewicht verpakking:	6930 g
Breedte verpakking:	279 mm
Diepte verpakking:	400 mm
Hoogte verpakking:	127 mm
LED-indicatoren:	Ja
Vormfactor:	Compact
Aantal Ethernet LAN (RJ-45)-poorten:	1
Ondersteund aantal accu's/batterijen:	1
Certificering:	GOST, REACH, UL 1449
Geluidsalarm(en):	Ja
Duurzaamheidscertificaten:	RoHS
Uitgangsvermogen:	330 W
Accu/Batterij oplaadtijd:	16 uur
Temperatuur bij opslag:	-15 - 40 °C
Frequentie:	50/60 Hz
Luchtvochtigheid bij opslag:	0 - 95 procent
Hoogte, in bedrijf:	0 - 9000 m
Hoogte bij opslag:	0 - 9000 m
Modem (RJ-11) poort:	1
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 95 procent
Batterijtechnologie:	Sealed Lead Acid (VRLA)
Surge energy rating:	450 J
Aantal AC uitgangen:	8 AC-uitgang(en)
Nominale input voltage:	220 V
Stopcontacttypes:	Type F
Golf protectie functies:	Fax, Modem, Network, Telephone
Stroom (max.):	10 A
Output power capacity:	0.55 kVA
Ingang operation voltage (min):	160 V
Ingang operation voltage (max):	278 V
Uitgang operation voltage (min):	- V
Uitgang operation voltage (max):	- V
Typische backup tijd op halve lading:	12 min
Typische backup tijd op volledige lading:	3 min
Hot-swap batterij:	Ja
Netspanning, in bedrijf:	220 V
Koude start:	Ja