Apc Back-UPS 500 Handleiding

Apc UPS Back-UPS 500

Lees hieronder de 📖 handleiding in het Nederlandse voor Apc Back-UPS 500 (4 pagina's) in de categorie UPS. Deze handleiding was nuttig voor 127 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

INSTALLATION

.apc.com

Back-UPS HS 500

User’s Manual

990-9236 3/04

3Remove Battery (if wall-mounting - if not proceed at Step 5)

0 - 40oC (32 - 104 oF)

1Placement 2Remove Connector Cover

Disconnect battery

wires from battery.

Remove battery.

Press cover release

tab (one each side)

and remove cover.

Caution: To prevent damage to the ribbon cable (not shown)

that connects the cover to the UPS, replace the cover after

removing the battery. Do not disconnect the ribbon cable

from the cover or the UPS.

Press the outlet cover release

tab (one each side); and pivot

cover off the unit.

Phone Line Out

4Mount Back-UPS (optional)

Wall Anchor

Mounting

Hole

Wall

5Connect/Install Battery, Install Battery Cover

Install battery cover.

Connect and install

the battery.

Press the outlet cover

release tab (one each

side); and pivot cover

off the unit.

6Connect Cable Modem,

Circuit Breaker

Push to Reset

Cable Out

Input:

230V~, 2.2A, 50-60Hz

Cable In

From Cable Provider

(Phone, Internet,

and/or CATV; or

DSS)

To Cable Modem,

VCR, DSS or TV

Cable Box

7Connect Phone Line

LAN

NetworkModem/Phone/Fax

RJ-45

Connectors

(can accept RJ-11)

RJ-45

Connectors

Phone Line In

(Standard or

DSL)

From Network Device

(or Computer Using a

Crossover Cable)

From Modem

DSS or CATV Receiver

8 10 Install Connector Cover

(optional)

or DSL to Surge

Connect Network

Equipment

To Hub

Router

11 Connect to Power Source and Switch on UPS Power

Connect Equipment Power Cords

Hub

or Router

Modem

Network Device

Output 1

Output 2

Output 3

to Surge Protection Protection (optional)

Align the holes in the

cover with the connector

cover release tabs (one

each side) and lower

connector cover.

7 AMP

The line cord used for this connection is supplied

by the user.

NOTE: APC recommends your network equipment

(computer, modem, router, hub, or other networked

devices) be completely installed, configured, and

tested prior to adding this UPS to the network.

Figure 2. InstallShield Welcome Screen

4. The software will then display the Licence Agreement (Figure 3). Please

read the Agreement and accept the terms by clicking Yes. To decline the

Agreement, click No - the software will not install.

Figure 3. InstallShield Licence Agreement Screen

If Autoplay is enabled on your computer, the software on the CD-ROM will

automatically start the installation program.

If Autoplay is not enabled on the computer, proceed as follows:

1. On the computer desktop of the display, double-click on My Computer, or

start Windows Explorer to locate the computer’s CD-ROM drive icon.

2. Double-click on the CD-ROM drive icon and then double-click on the

setup.exe icon. The software will start and display the InstallShield

Wizard Screen (Figure 1). The software will begin the installation

process. To stop the installation, click Cancel.

Figure 1. InstallShield Wizard Screen

3. After about 4 seconds, the software will display the Welcome Screen

(Figure 2). To continue, click Next. To cancel the installation, click

Cancel.

There are six status indicators (lights) on the front panel of the Back-UPS (On Line, On Battery,

Overload, Replace Battery, TX/RX, and ACT/LNK).On Line (green) - is lit whenever AC utility power is

powering the outlets.

On Battery (yellow) - is lit whenever the battery of the

Back-UPS is supplying power to the equipment connected to

the outlets.

Four Beeps Every 30 Seconds - this alarm is

sounded whenever the Back-UPS is running On

Battery. Consider saving work-in-progress.

Overload (red) - is lit whenever power demand has

exceeded the capacity of the Back-UPS.

Continuous Tone - this alarm is sounded

whenever the Back-UPS outlets are overloaded.

Replace Battery (red) - is lit whenever the battery is

near the end of its useful life, or if the battery is not

connected (see above). A battery that is near the end of its

useful life has insufficient run-time and should be replaced.

Chirps for 1 Minute Every 5 Hours - this

alarm is sounded whenever the battery has failed

the automatic diagnostic test.

Continuous Beeping - this alarm is sounded

whenever a low battery condition is reached.

Battery run-time is very low. Promptly save any

work-in-progress and exit all open applications.

Shutdown the operating system, computer, and the

Back-UPS.

STATUS INDICATORS AND ALARMS

Back-UPS

0 0

Replace

Battery

OverloadOn Battery

On-Line

ACT/LNK

TX/RX

.apc.com

TX/RX (green) - is lit whenever the Back-UPS is

sending or receiving data over the network.

ACT/LNK (green) - is lit whenever the Back-UPS is

connected to equipment and is ready and waiting to send

or receive data.

TRANSFER VOLTAGE/SENSITIVITY ADJUSTMENT (Optional)

Circuit Breaker - the rocker-type circuit breaker switch

located on the bottom panel of the Back-UPS will trip if an

overload condition forces the Back-UPS to disconnect

itself from AC utility power. If the switch trips, disconnect

non-essential equipment. Reset the circuit breaker by

pushing it to the ON position.

Follow the

on-screen

instructions.

INSTALL AND SETUP SOFTWARE

In situations where the Back-UPS or connected equipment appears too sensitive to input voltage, it may be

necessary to adjust the transfer voltage. This is a simple task requiring use of the front panel pushbutton. It can

also be accomplished using the Configuration Page Screen in the supplied software (see Install and Setup

Software). To adjust the transfer voltage, proceed as follows:

1. Plug the unit into an AC utility power source; the Back-UPS will go into Standby Mode (no indicators lit).

2. Press the front panel pushbutton fully inward for 10 seconds. All indicators on the Back-UPS will flash to

acknowledge going into Programming Mode.

3. The Back-UPS will then indicate its current Sensitivity Setting, as shown in the following table.

4. To select the Low Sensitivity setting, press the pushbutton until the yellow indicator is flashing.

5. To select the Medium Sensitivity setting, press the pushbutton until the yellow and red indicators are

flashing.

6. To select the High Sensitivity setting, press the pushbutton until yellow and both red indicators are flashing.

7. To exit without changing the Sensitivity Setting, press the pushbutton until the green indicator is flashing.

8. Once in Programming Mode, if the pushbutton is not pressed within 5 seconds, the Back-UPS will exit

Programming Mode; all indicators will extinguish.

Indicators

Flashing

Sensitivity

Setting

Input Voltage

Range (for

utility

operation)

Use When

(yellow)

Low 160 - 278 Vac Input voltage is extremely low or high. Not

recommended for computer loads.

(yellow, and red)

Medium

(factory default)

180 - 266 Vac Back-UPS frequently goes On Battery

(recommended).

(yellow, red, and red)

High 196 - 256 Vac Connected equipment is sensitive to voltage

fluctuations.

5. The software will display the Choose Destination Location Screen (Figure

4). Select Browse to find a location, click Next to accept the system default

location, the system will then display the Setup Status Screen (Figure 5).

Click on Cancel to stop the installation.

Figure 4. Choose Destination Location Screen

Figure 5. Setup Status Screen

6. The software then displays the InstallShield Wizard Complete Screen (Figure 6). Select

Finish to quit the installation program..

Figure 6. InstallShield Wizard Complete Screen

7. To launch the program, go to the Start menu, select APC, then select APC Back-UPS HS

(Figure 7). Continued on the next page -

Figure 7. APC Software Startup Menu Selections

Input Voltage (on line) 180 - 266 Vac

Input Frequency 47 - 63 HZ (autosensing)

Output Wave Form (On battery) Stepped Sine Wave

Maximum Load 500 VA 300 Watts

Operating temperature 32 - 104° F (0 to 40° C)

Storage temperature 5 - 113° F (-15 to 45° C)

Operating humidity 10 - 90% non-condensing

Storage humidity 10 - 95% non-condensing

Physical: (H x W x D) 14.65 x 8.85 x 4.13 in

(37.2 x 22.5 x 10.5 cm)

Weight 16.3 lb (7.4 kg)

Typical Recharge Time 6 - 8 hours

EMI Classification EN50091-2, Class B

Approvals NEMKO-GS, CE, and GOST

Specifications

8. Following installation, the Back-UPS HS software is available in the Start

menu. Upon launching the program, it searches for all Back-UPS HS devices on

the network, and will identify them as shown in Figure 8 by IP Address and

MAC Address. The IP Address is automatically assigned to the Back-UPS by

the DHCP services from your hub or router. IP Addresses assigned by the

DHCP service may automatically change over time. Thus, APC recommends

you do not bookmark the IP Address, as you may not be able to access it

through your browser. The MAC Address is assigned to the Back-UPS HS 500

at the factory.

Figure 8. Back-UPS HS IP Address and MAC Address Screen

9. If there are no DHCP services on the network, or if you want to assign an IP

Address you can easily remember, you can manually assign an IP Address to

the Back-UPS by clicking on the IP Configuration button. The address you

assign must follow the format shown in Figure 9 and cannot duplicate an

address already assigned. Figure 10 shows the IP Configuration Screen with the

IP Address fields set to zero (0).

To assign an IP Address to your computer, please read and follow the directions

that came with your computer.

Figure 9. Assign IP Address Screen

Figure 10. Blank Assign IP Address Screen

10. You can assign a name to the Back-UPS by clicking on the Assign Name

button (Figure 8) and entering the name in the Assign Name Screen dialog. It

will appear in the column to the left of the IP Address of the device (Figure 11).

Names should not be duplicated.

Figure 11. Assign Name Screen

11. To reset the Back-UPS HS to factory default values, use the UPS Settings

button. If the Back-UPS HS does not reset using the software, remove the

Battery Cover and insert a small object (about 2 inches in length) into the hole

located next to the telephone jack (Figure 12) for approximately 5 seconds.

Note: The telephone jack is provided for factory testing only - do not connect

anything to this jack).

Figure 12. Manual Reset Access

12. Before performing any UPS maintenance task, check the Status of the UPS by

clicking on the Status link. The screen shown in Figure 13 will be displayed.

Figure 13. Back-UPS HS 500 Status Screen

13. To change the configuration of the Back-UPS or perform UPS maintenance,

you must log on to the web page (Figure 11) by clicking on the UPS Settings

button.

When this page is displayed, enter a default Username of apc, and a default

Password of apc. To change the Username or Password, you must log on and

then click Maintenance (Figure 14).

Note: You can also access the Logon Page Screen by entering the IP Address

into the Address line of your browser.

Manual Reset

Access

Figure 14. Log On Screen

14. Using the Maintenance Screen (Figure 15), you can perform a Battery Self-

Test, Update the Battery Replacement Date, Change the User Name or

Password (as previously discussed) then click Update Now, or you can

Restore Factory Defaults. Note: You must be logged on to perform any of

these tasks.

Figure 15. Maintenance Page Screen

15. Using the Configuration Page Screen (Figure 14), you can adjust the

Sensitivity of the Back-UPS. By adjusting the Sensitivity, the Back-UPS will

allow the unit to switch to battery power depending on the quality of the AC

utility power being supplied to the unit. Use of the Sensitivity settings are for

the following conditions:

Low - Use only for extreme conditions of low input voltage. Not recommended

for computer loads.

Medium - Back-UPS frequently goes On Battery due to low input voltage

(recommended).

High - Connected equipment is sensitive to low voltage.

The Configuration Page Screen also allows you to enable or disable the

Audible Alarm. If enabled, this alarm operates as described in the Status

Indicators and Alarms section of this manual. If disabled, the Back-UPS will

quiet the alarm.

Additionally, the Configuration Page Screen allows you to adjust the voltage

Transfer Points. The Back-UPS will transfer to On Battery operation at input

voltages Above or Below the points selected in the drop-down Volts menu.

Finally, the Configuration Page Screen provides Output Control for the four

outlets of the Back-UPS. Control consists of switching power On or Off at

Output 1, Output 2, or the two outlets of Output 3. It also allows you to

Reboot loads by automatically switching power Off and then On at the selected

outlet. If an outlet is switched Off, it cannot be rebooted.

To use the Configuration Page Screen, you must be logged on to the Back-

UPS. Select the desired function and click on the Apply button. To reset the

unit to the factory defaults, click the Reset button.

Figure 16. Configuration Page Screen

16. The About Page Screen provides general information about your Back-UPS

including Network Parameters (IP and MAC Addresses), as well as Technical

Parameters (Model, Serial Number, Firmware Revision, Web Firmware

Revision, UPS Date of Manufacture, and Battery Replacement Date).

Figure 17 About Page Screen

Product specificaties

Merk:	Apc
Categorie:	UPS
Model:	Back-UPS 500
Kleur van het product:	Beige
Gewicht:	5730 g
Breedte:	91 mm
Diepte:	284 mm
Hoogte:	165 mm
Geluidsniveau:	40 dB
Gewicht verpakking:	6640 g
LED-indicatoren:	Ja
Afmetingen verpakking (BxDxH):	241 x 368 x 178 mm
Certificering:	C-tick, CE, EN 50091-1, EN 50091-2, GOST, VDE, RoHS.
Geluidsalarm(en):	Ja
Uitgangsvermogen:	300 W
Accu/Batterij oplaadtijd:	6 uur
Temperatuur bij opslag:	-15 - 45 °C
Frequentie:	50/60 Hz
Luchtvochtigheid bij opslag:	0 - 95 procent
Hoogte, in bedrijf:	0 - 3000 m
Hoogte bij opslag:	0 - 15000 m
Afmetingen (B x D x H):	91 x 284 x 165 mm
Overbelastingsprotectie:	Ja
Producten per pallet:	96 stuk(s)
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 95 procent
Batterijtechnologie:	Sealed Lead Acid (VRLA)
Type batterij:	RBC2, RBC2J
Surge energy rating:	320 J
Input-connectietype:	IEC C13
Output power capacity:	0.5 kVA
Netspanning, in bedrijf:	230 V
Spanningsbeveiliging:	Ja
Number of output IEC jumpers:	4