Apantac SDI-FIB Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Apantac SDI-FIB (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 39 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
1. SDI-FIB-Tx: SDI to Fiber transmitter w/ DC5V
1.5A Power Supply
2. SDI-FIB-Rx: Fiber to SDI receiver w/ DC5V
1.5A Power Supply
3. DC 5V 1.5A Power Supplies
4. Options: 12V XLR male to mini XL female
cable for direct power from the camera
5. User Manual
6. Pelican like hard carrying case
Product Specification
ï‚· Transmission of Multi-rate SDI (3G/HD/SD-
SDI) video over a single fiber. (SMPTE-
424M, SMPTE-292M and SMPTE-259M)
ï‚· Compatible with single-mode or multi-mode
fiber
ï‚· Equalized on the inputs and reclocked on the
output to maximize performance up to 120m
for 3G and 140m for HD-SDI
ï‚· Extension limit: 18 mile (30 km) for 1.485
Mbps, 12.5 miles (20 km) for 3G (1080P)
ï‚· Recommended fiber optic cable: Glass single
-mode fiber with 1310, 1550nm with ST ter-
minated connectors
ï‚· General Electrical specifications
ï‚· Link power budget: Minimum 11dB
ï‚· BNC connectors: 75 ohm male
ï‚· Mechanical specifications
ï‚· Dimension: 19.5mm x 19.5mm x 82.7mm
(WxHxD)
ï‚· Environmental Specifications
ï‚· Operating temperature: -20C to 70C
ï‚· Storage temperature: -30C to 85C
ï‚· Humidity: 5% to 95% RH
MAZAMA
SDI-FIB
Installation and
Apantac LLC
7556 SW Bridgeport Road
Portland, OR 97224
T: +1 (503) 968 3000
F: +1 (503) 389 7921
E: info@apantac.com
3G/HD/SD-SDI to Fiber Extender
Mazama SDI-FIB 0817
What’s in the Box
DC Power Adaptor Pin-out
Startup and Installation
(1) Unpack the content from the hard carrying
case
(2) Connect the SDI-FIB-Tx’s BNC side to the SDI
source. (Note: It is recommended to connect
the BNC directly to the source. Any interme-
diate cables or barrows may impact the signal
performance)
(3) Plug the +5V DC power adaptor to SDI-FIB-
Tx
(4) Connect the SDI-FIB-Rx’s BNC to the display.
(Note: It is recommended to connect the BNC
directly to the source. Any intermediate ca-
bles or barrows may impact the signal perfor-
mance)
(5) Plug the +5V DC power adaptor to SDI-FIB-
Rx
Connection Diagram
there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause
harmful interference to other devices, which can be
determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
ï‚· Reorient or relocate the receiving device.
ï‚· Increase the separation between the equipment.
ï‚· Connect the equipment into an outlet on a circuit dif-
ferent from that to which the other device(s) are con-
nected.
ï‚· Consult the manufacturer or field service technician for
help.
ï‚· Type of protection against electric shock: Class I equip-
ment
ï‚· Degree of protection against electric shock: Not classified
- no applied parts
ï‚· Classification according to the degree of protection
against ingress of water as detailed in the current edition
of IEC 529: IPX0, ordinary equipment
ï‚· This equipment is not suitable for use in the presence of
flammable anesthetics or oxygen
ï‚· Mode of operation: continuous operation
Warranty Information
1 One ( ) Year Warranty
Apantac warrants this fiber-optic 3G-SDI extension
product to be free from defects in workmanship and
materials, under normal use and service, for a period
of ( ) year from the date of purchase from One 1
Apantac or its authorized resellers.
If a product does not work as warranted during the
applicable warranty period, Apantac shall, at its option
and expense, repair the defective product or part,
deliver to customer an equivalent product or part to
replace the defective item, or refund to customer the
purchase price paid for the defective product.
All products that are replaced will become the property
of Apantac.
Replacement products may be new or reconditioned.
FCC/CE Statement
This device complies with part 15 of FCC Rules and EN
55022/61000-3 for CE certification. Operation is sub-
ject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this de-
vice must accept any interference received, including
interference that may cause undesired operation. This
equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to part
15 and 2 of FCC Rules and EN 55022/61000-3 for CE
certification. These limits are designed to provide rea-
sonable protection against harmful interference when
the equipment is operated in a residential installation.
This equipment generates, uses, and can radiate radio
frequency energy and. if not installed and used in ac-
cordance with the instruction guide, may cause harm-
ful interference to radio communications. However,
there is no guarantee that interference will not occur
in a particular installation. If this equipment does
cause harmful interference to radio or television re-
ception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the follow-
ing measures:
ï‚· Re-orient or relocate the receiving antenna.
ï‚· Increase the separation between the equipment and
the receiver.
ï‚· Connect the equipment into an outlet on a circuit differ-
ent from that to which the receiver is connected.
ï‚· Consult a service representative for help.
Properly shielded and grounded cables and connectors
must be used in order to comply with FCC/CE emis-
sion limits. Changes or modifications not expressly
approved by the party responsible for compliance
could void the user s authority to operate the equip-
ment.
UL/IEC Statement
This equipment has been tested and found to
comply with the limits for medical devices in IEC
60601-1:1994. These limits are designed to provide
reasonable protection against harmful interference in a
typical medical installation.
This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in ac-
cordance with the instructions, may cause harmful
interference to other devices in the vicinity. However,
Any replaced or repaired product or part has a ninety
(90) day warranty or the reminder of the initial war-
ranty period, whichever is longer.
Warranty Limitation and Exclusion
Apantac shall have no further obligation under the
foregoing limited warranty if the product has been
damaged due to abuse, misuse, neglect, accident,
unusual physical or electrical stress, unauthorized
modifications, tampering, alterations, or service other
than by Apantac or its authorized agents, causes oth-
er than from ordinary use or failure to properly use
the Product in the application for which said Product
is intended.
Dispose of Old Electrical & Electronic
Equipment
(Applicable in the European Union and other Europe-
an countries with separate systems)
This symbol on the product or on its
packaging indicates that this product
shall not be treated as household
waste. Instead it shall be handed over
to the applicable collection point for
the recycling of electrical and elec-
tronic equipment. By ensuring this product is
disposed of correctly, you will help prevent po-
tential negative consequences for the environ-
ment and human health, which could otherwise
be caused by inappropriate waste handling of this
product. The recycling of materials will help to
conserve natural resources. For more detailed
information about recycling of this product,
please contact your local city office, your house-
hold waste disposal service or the shop where
you purchased the product.


Product specificaties

Merk: Apantac
Categorie: Niet gecategoriseerd
Model: SDI-FIB

Heb je hulp nodig?

Als je hulp nodig hebt met Apantac SDI-FIB stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Apantac

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd