Anthro Fit Adjusta Unit Handleiding

Anthro Bureau Fit Adjusta Unit

Lees hieronder de 📖 handleiding in het Nederlandse voor Anthro Fit Adjusta Unit (4 pagina's) in de categorie Bureau. Deze handleiding was nuttig voor 88 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Questions? 1-800-325-3841

Thank you for buying our Products!

Please return the enclosed Registration Card to receive our product

updates, new catalogs, and sale ﬂyers.

Anthro Corporation Technology Furniture®

10450 SW Manhasset Drive

Tualatin, Oregon 97062

anthro.com

Anthro Corporation Technology Furniture® 10450 SW Manhasset Drive Tualatin, Oregon 97062 anthro.com

SAVE THESE INSTRUCTIONS! Rev. C January 2006

Hello! Thank you for choosing Anthro.

Before beginning assembly of your Adjusta Unit, take a moment to review the parts listed on the next page

to verify that your shipment is complete. Please review the assembly instructions of all Anthro products you

purchased and are planning to include in this installation, prior to beginning this assembly.

30”/36”/48” wide Adjusta Unit

Assembly Instructions

1-800-325-3841

To make the assembly of your Adjusta Unit even easier, we have included all of the required tools. The handy

Hex Driver Bit can be used in your electric drill in place of the Hex Driver. Your Adjusta Unit is heavy! A second

person will make this assembly procedure much easier.

Hex Driver 5/32” ............................................................ 375-5000-00

Hex Driver Bit 5/32” ..................................................... 375-5003-00

Hex Key 5/32” ................................................................. 375-5016-00

Hex Key 3/16” ................................................................. 375-5028-00

3-Way Wrench ............................................................. 225-5196-03

8 oz. Rubber Mallet ..................................................... 375-5022-00

Anthro Corporation Technology Furniture® 10450 SW Manhasset Drive Tualatin, Oregon 97062 1-800-325-3841 anthro.com

01–ﬁt Adjusta Fixed Worksurface Qty. 1 ....................... (see below)

30” Wide Fixed Worksurface (FAJ30zz/xx3) ....100-6454-00

36” Wide Fixed Worksurface (FAJ36zz/xx3) ....100-6455-00

48” Wide Fixed Worksurface (FAJ48zz/xx3) ....100-6456-00

02–ﬁt Adjusta Caddy Worksurface Qty. 1 ....................... (see below)

30” Wide Caddy Worksurface (FAJ30zz/xx3)..100-6458-00

36” Wide Caddy Worksurface (FAJ36zz/xx3) ..100-6459-00

48” Wide Caddy Worksurface (FAJ48zz/xx3) ..100-6460-00

03– Adjusta Mechanismﬁt ...............Qty. 1 ....................... (see below)

(The Adjusta Mechanism is packaged separately & requires assembly)

30” Wide Adjusta Mechanism (FAJ30zz/xx3) ...225-5545-00

36” Wide Adjusta Mechanism (FAJ36zz/xx3) ...225-5546-00

48” Wide Adjusta Mechanism (FAJ48zz/xx3) ...225-5547-00

04– Small Support Bracket X .............Qty. 1 ...................225-2014-00

05– 24.875” Vertical Legs .................Qty. 4 ...................125-5230-00

06– Adjusta Base Tubes ......................Qty. 2 ..................125-5276-00

07– Cross Tubes ....................................Qty. 2 ....................... (see below)

30” Wide Cross Tube (FAJ30zz/xx3) ...................125-5219-00

36” Wide Cross Tube (FAJ36zz/xx3) ...................125-5220-00

48” Wide Cross Tube (FAJ48zz/xx3) ...................125-5214-00

08– Insert Screws .................................Qty. 4 ...................325-5052-00

09– 2.0” Large End Caps ...................Qty. 4 ...................175-5157-00

10– Caster Inserts ...............................Qty. 4 ...................525-5032-00

11– 3” Locking Casters ......................Qty. 2 ...................150-5053-00

12– 5/16-18 Boltsﬁt ..............................Qty. 8 ...................325-5194-00

13– Tube Washersﬁt .........................Qty. 8 ..225-2050-00 or 225-3522-00

14– 3” Non-Locking Casters ........... Qty. 2 ...................150-5052-00

15– 3/4” Wood Screws ........................Qty. 42 ................325-5106-00

16– Back Trough .................................... Qty. 1 ....................... (see below)

30” Wide Back Trough (F3029zz/xx3) ................225-2290-00

36” Wide Back Trough (F3629zz/xx3) ................225-2291-00

48” Wide Back Trough (F4829zz/xx3) ................225-2292-00

17– Support Screws ............................Qty. 8 ...................325-5010-00

18– Small Support Bracket Y ............Qty. 1 ...................225-2015-00

19– 1/4-20 Button Head Screws ......Qty. 4 ...................325-5003-00

20– 1.5” Small Caps .............................Qty. 4 ...................175-5156-00

All Fastener quantities listed here are the minimum needed

for your Adjusta Unit assembly. There may be a few extra

Fasteners included, which are not counted in the Parts List.

Component list for part #’s FAJ30zz/xx3, FAJ36zz/xx3 & FAJ48zz/xx3

NOTE: Detailed views of all Hardware are provided with each Assembly Step.

10 12

09 13 14

15 16

Step 12

Align the Base Assembly on the Vertical Tubes as shown.

Secure the Base Assembly by inserting a Bolt through a ﬁt

Tube Washer. Then insert the Bolt through the Base Tube

and carefully thread it into the Vertical Tubes.

Repeat for the remaining three Bolts and tighten all Bolts.

(5/16-18 X 3.5”) Boltﬁt

325-5194-00

ﬁt Tube Washer

225-2050-00 or 225-3522-00

Locking Casters

ﬁt Bolt

ﬁt Tube

Washer

1.5” Small

End Cap

Rotate Knobs

to adjust

Caddy angle.

Squeeze Paddle

to adjust Caddy height.

Step 13

Insert the four 1.5” Small End Caps into the Vertical Legs.

Congratulations! Your assembly is complete.

Please return the enclosed Registration Card to receive

our product updates, new catalogs, and sale ﬂyers.

Thank you for choosing Anthro!

Adjust the Caddy Worksurface height by:

1. Squeezing and holding the Paddle.

2. Reposition the Caddy to the desired location.

3. Release the Paddle.

Adjust the Caddy Worksurface angle by:

1. Rotating the Knobs counterclockwise.

2. Reposition the Caddy to the desired angle.

3. Rotate the Knobs clockwise.

Step 9 (requires Worksurface to be 12” from ﬂoor)

Rotate the Caddy Worksurface so the predrilled holes face

upward and the Lip faces the front of the Adjusta Unit.

Slide the Caddy under the Mechanism and align

the three holes located on each end of the Caddy and

Mechanism.

Secure the Caddy using a total of six Wood Screws. Then,

secure the Paddle to the Caddy using four Wood Screws.

NOTE: Make certain the Cable for the Paddle is positioned

underneath the Adjusta Bar.

Anthro Corporation Technology Furniture® 10450 SW Manhasset Drive Tualatin, Oregon 97062 1-800-325-3841 anthro.com

Step 2 (uses the 3-Way Wrench)

Unpack the remaining Adjusta Mechanism components

and arrange them as shown at right.

Place one Crossbar end onto the lower Crossbar

Button and Threaded Bolt (located on each of the Arm

Mechanisms). Secure the Crossbar to the Arm Mechanism

using one 5/16” Hex Nut onto the Threaded Bolt.

Repeat for remaining Crossbar end and Arm Mechanism.

5/16” Hex Nut

(included with 225-554x-00) DETAIL VIEW

Arm Mechanism

Thread-

ed Bolts

5/16” Hex

Nut

Paddle

Brake/Paddle As-

sembly

Arm Mechanism Crossbar

Lower Crossbar

Button

NOTE: it is very important that you attach the

Crossbar ONLY to the Lower Crossbar Button.

Step 1a

Your Adjusta Mechanism comes unassembled and is

boxed separately inside the Adjusta Unit package.

Begin to assemble the Mechanism by ﬁrst locating the Adjusta

Crossbar and Brake/Paddle Assembly, position it as shown at

right. Depress the Paddle once to free the Brake Shaft.

Place the Brake Shaft between the two center Crossbar

Flanges. Insert the Post through both center Crossbar

Flanges and Brake Shaft.

Cotter Pin

(included with 225-554x-00)

Center Crossbar Flanges

Cotter Pin

Step 1b

Install the Cotter Pin through the single opening of the

Post to secure into place.

NOTE: included with Adjusta Mechanism is a small bag of

Hardware containing the (1) Post, (1) Cotter Pin, (2) Hex

Nuts, (2) Wood Screws, & (2) Cable Mounts.

Post

(included with 225-554x-00)

Brake Shaft

Brake/Paddle Assembly

Crossbar

Post

3/4” Wood Screw

325-5106-00

Step 10

Install two Caster Inserts into each Base Tube and se-

cure with one Insert Screw per Insert.

Insert one Locking and one Non-Locking Caster into

each Insert of a Base Tube as shown.

Insert two End Caps into the ends of both Base Tubes.

Insert Screw

(with pink threads)

325-5052-00

Locking

Caster

Caster Inserts placed

into the large holes

Leave these two side holes open

Non-Locking

Caster

Paddle

Adjusta Bar

(12” high surface shown shaded)

FAJ30zz/xx3, FAJ36zz/xx3 & FAJ48zz/xx3

Step 11

Attach a Cross Tube to a Base Tube by inserting a Bolt ﬁt

through a Tube Washer, then insert the Bolt through the

Base Tube and carefully thread into the Cross Tube.

Repeat this procedure for other Cross Tube. Then tighten

all Bolts. ﬁt

ﬁt Tube Washer

225-2050-00 or 225-3522-00

Cross Tube

ﬁt Tube

Washer

(5/16-18 X 3.5”) Boltﬁt

325-5194-00

ﬁt Bolt

Base Assembly

Wood Screw

Product specificaties

Merk:	Anthro
Categorie:	Bureau
Model:	Fit Adjusta Unit
Kleur van het product:	Zwart
Breedte:	1524 mm
Diepte:	927 mm
Hoogte:	793.75 mm
Maximale gewichtscapaciteit:	68 kg
Paneelmontage-interface:	Nee mm
Draaihoek:	360 °
Afmetingen (B x D x H):	1524 x 927 x 793.75 mm
Bereik kantelhoek:	0 °
Lift:	0 cm