Anthro Bench Handleiding

Anthro Bureau Bench

Lees hieronder de 📖 handleiding in het Nederlandse voor Anthro Bench (2 pagina's) in de categorie Bureau. Deze handleiding was nuttig voor 7 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

TECHNOLOGY FURNITURE®

01– 48” Wide Bench Shelf ...........Qty. 1 ..................(see below)

28” Deep (S4829zz/xx & S4835zz/xx) ..............100-6406-00

36” Deep (B4829zz/xx & B4835zz/xx) .............100-6349-00

02– Bench Leg Assemblies ...........Qty. 2 ..................(see below)

25” Bench Legs (S4829zz/xx & S4835zz/xx) ..835-5008-00

31” Bench Legs (B4829zz/xx & B4835zz/xx) 835-5009-00

03– Bench Arm Left .......................Qty. 1 ............. 225-5357-00

04– Cross Ends ................................Qty. 2 ............ 225-5334-00

05– 11/4” Wood Screws .................Qty. 12 ...........325-5178-00

06– Glide Insert Screws ...............Qty. 4 ............. 325-5052-00

07– 2.5” End Caps ..........................Qty. 4 ............ 175-5158-00

08– Glide Inserts .............................Qty. 4 ............. 525-5030-00

09– Glides (1/2-13 X 2”) ................Qty. 4 ...........325-5165-00*

10– Cap Screws (5/16-18 X 4”) ...Qty. 8 .............325-5166-00

11– Curved Washers .....................Qty. 8 . 225-2050-00 or 225-3522-00

12– Bench Base Tubes ...................Qty. 2 ..................(see below)

28” Deep (S4829zz/xx & S4835zz/xx) ..............125-5225-00

36” Deep (B4829zz/xx & B4835zz/xx) .............125-5183-00

Enclosed Parts List

Detailed views of all Hardware is provided with each Assembly Step

13– 15” Bench Buttress ................Qty. 2 ............. 225-5386-00

14– 41.5” Bench Cross Tubes ....Qty. 2 ............. 125-5184-00

15– Keps Nuts (1/4-20) ..................Qty. 8 .............325-5130-03

16– Pan Screws (1/4-20 X .5”) ....Qty. 8 .............325-5003-00

17– Bench Arm Right .....................Qty. 1 ............. 225-5358-00

18– Support Screws .......................Qty. 20 ........... 325-5010-00

19– 48” Bench Pans .......................Qty. 2 ............. 225-5370-00

All Screw quantities listed here are the minimum needed

for your Bench assembly. There may be a few extra

Screws included, which are not counted in the Parts List.

To make the assembly of your Anthro Bench even easier, we

have included the required tools.. The handy Hex Driver Bit

can be used in your electric drill in place of the Hex Driver.

20- Hex Driver 5/32” .......................Qty. 1 .............375-5000-00

21- Hex Driver Bit 5/32” ................Qty. 1 .............375-5003-00

22- Hex Key 1/4” ..............................Qty. 1 .............375-5024-00

3-Way Wrench(not shown) ..............Qty. 1 .............225-5196-03

Anthro Corporation Technology Furniture® 10450 SW Manhasset Drive Tualatin, Oregon 97062

SAVE THESE INSTRUCTIONS! anthro.comSeptember 2004 Rev. E

These Assembly Instructions are for the 48” AnthroBench models: B4829zz/xx, S4829zz/xx, B4835zz/xx

& S4835zz/xx. Before beginning assembly of your AnthroBench, please take a moment to review the parts listed below

to verify that your shipment is complete.

11 14

15 16

48” AnthroBench

Assembly Instructions

✔Does your Bench have 5” Casters?*

(If you purchased a 640RT - your Caster Part

Numbers are given here.)

5” Locking Caster

150-5024-00

5” Non-Locking Caster

150-5025-00

Your AnthroBench is heavy!

A second person will make this

assembly procedure much easier.

Step 7

Place the Bench Shelf (laminate facing down) onto the

ﬂoor.

With the help of another person, carefully rotate the Leg

Assembly (from Step 6) over onto the Shelf.

Position the holes on the Pans and Arms to align with the

twelve predrilled holes on the Shelf. Insert two Wood

Screws through each center opening of the Bench Pans

(shown encircled at right).

Install the remaining Wood Screws into each of the Arms

and Pans, a total of twelve Wood Screws will be installed.

In preparation for Step 8, carefully rotate your Anthro-

Bench back over onto the Glides.

Step 8 (requires a 3-Way Wrench)

FIRST- from the rear of your Bench, align one Buttress

with one hole on the Back Pan. Install a Pan Screw

through the Buttress and loosely capture using a Keps Nut

on the opposite side.

SECOND- position one Cross End on the remaining

Buttress end and install a Pan Screw and Keps Nut in the

same manner, but do not fully tighten.

THIRD- rotate the Buttress to align the Cross End with

two openings on the Leg. Secure the Cross End to the

Leg using two Support Screws.

Repeat this entire procedure for the remaining Buttress

and Cross End on the opposite end.

Tighten all Pan Screws, Support Screws & Keps Nuts.

Congratulations! Your 48” AnthroBench assembly is

complete. Please return the enclosed Registration Card to

receive our product updates, new catalogs, and sale ﬂyers.

Thank you for choosing Anthro!

Questions? 1-800-325-3841

11/4” Wood Screw

325-5178-00

(1/4-20 X .5”) Pan Screw

325-5003-00

(1/4-20) Keps Nut

325-5130-03

Buttress

Back Pan hole

Support Screw

325-5010-00

FIRST Install this Pan Screw

SECOND Install this Pan Screw

THIRD Install the Cross End

Lower Metal Mounts

Cable Grommet

Workstation Screw

(not counted in Parts List)

325-5092-00

Removal of Leg Covers & Cable Grommets

Remove the Leg Cover by: 1. First removing the top two

Workstation Screws. 2. Slightly lift the Cover upward and

off the lower metal mounts.

Cable Grommets are snapped into and out of each of the

circular Leg openings.

NOTE: The purpose of the Buttress is not to

support your Bench Shelf. It is intended to make

your Bench absolutely rigid under extreme weight

conditions.

Pans

Arms

Rounded Edge of Shelf

Predrilled holes

Anthro Corporation Technology Furniture® 10450 SW Manhasset Drive Tualatin, Oregon 97062 anthro.com

Step 4

Determine the height of your Shelf. These Instructions will

place your ﬁnal Shelf height at either 29” or 35” from the ﬂoor

(depending on which height Bench you purchased).

The holes along the Leg Assemblies are spaced at 1”

increments. Adjusting either one hole up or down will modify

the ﬁnal Shelf height by 1” respectively. Rotating the Glides

will also provide additional height adjustment.

NOTE: Your Shelf height can be adjusted at a later time if needed,

however, Assembly Steps 5 through 8 will need to be disassembled

and reassembled again.

Step 5

Position the Left Bench Arm onto the Left Leg Assembly.

Align the top two openings of the Arm with Hole 2 of the

Leg Assembly. Loosely install a Support Screw through the

top two holes of the Arm into the Leg.

Install the remaining six Support Screws into the Left Arm,

but do not fully tighten any of the Support Screws.

Repeat entire procedure for the Right Bench Arm on the

Right Leg Assembly.

Step 6 (requires a 3-Way Wrench)

Position a Bench Pan between the Arms, aligning the

two tabs on each Arm with the two holes in the lower

corners of a Pan. Insert a Pan Screw through the Pan

and Arm Tab- capturing it with a Keps Nut (but do not

fully tighten). Repeat this procedure for the remaining

end of the Pan and for the second Pan.

Tighten all Pan and Support Screws.

NOTE: the 3-Way Wrench can be used to assist in tightening

the Keps Nuts.

Questions? 1-800-325-3841

(1/4-20 X .5”) Pan Screw

325-5003-00

Support Screw

325-5010-00

Insert Screw

(small pink patch on end)

325-5052-00

Glide Inserts placed

into the large holes

Leave these two holes open

(5/16-18 X 4”) Bench Cap Screw

325-5166-00

Curved Washer

225-2050-00 or 225-3522-00

29” or 35”

Left Leg Assembly

Right Leg Assembly

Side holes

Cross Tubes

Leave top two

Holes open Hole 2

Left Leg Assembly

Right Leg Assembly

(1/4-20) Keps Nut

325-5130-03

(5/16-18 X 4”) Bench Cap Screw

325-5166-00

Curved Washer

225-2050-00 or 225-3522-00

Leave these two holes open

Lower holes

Arms

Second Pan shown installed

REMINDER: You may want to measure

your equipment to make sure it ﬁts into

the selected Shelf location.

48” AnthroBench

Assembly Instructions

Left Bench Arm

Step 3

Position the Right Leg Assembly with two (from Step 2)

Cross Tubes as shown. Insert one Bench Cap Screw

with a Curved Washer through a side hole, carefully

threading the Screw into the Cross Tube.

Repeat entire procedure for the remaining three

side holes.

Step 2

Orient one Bench Leg Assembly with one Base Tube

Assembly (from Step 1). The Glide Inserts should be facing

down.

Insert one Bench Cap Screw through one Curved Washer,

then carefully insert through one of the lower holes on

the Base Tube, threading into the Right Leg Assembly.

Repeat this procedure for the remaining three lower holes

on the Right & Left Leg Assembly.

STOP: If you are upgrading to 5” Casters do so now.

Finally, thread one Bench Glide into each Glide Insert.

Left Leg

Assembly

Right Leg

Assembly

Thread one Glid e

int o ea c h Gl i d e

Inse r t AFT ER the

Base Tubes have been

installed to the Legs.

NOTE: Loosen these

Support Screws (if

needed) to allow the

Base Tube to install

easier.

Glide Inserts

Step 1

Install two Bench Glide Inserts into each Bench Base Tube

and secure with one Insert Screw per Insert.

Pop two End Caps into the ends of both Base Tubes.

Product specificaties

Merk:	Anthro
Categorie:	Bureau
Model:	Bench
Kleur van het product:	Zwart
Breedte:	1219.2 mm
Diepte:	914.4 mm
Hoogte:	889 mm
Maximale gewichtscapaciteit:	181.4 kg

Heb je hulp nodig?

Als je hulp nodig hebt met Anthro Bench stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Bureau Anthro

Anthro Trolley Handleiding

8 Februari 2024

Anthro Elevate II Handleiding

8 Februari 2024

Anthro Security Cart Handleiding

8 Februari 2024

Anthro Fit Adjusta Unit Handleiding

8 Februari 2024

Anthro Large Carts Handleiding

8 Februari 2024

Anthro Steve's Station Advanced Handleiding

8 Februari 2024

Anthro Fit Console Unit Handleiding

8 Februari 2024

Anthro POC Cart Handleiding

8 Februari 2024

Anthro Elevate Single Surface Handleiding

8 Februari 2024

Anthro Zido cart Handleiding

8 Februari 2024

Handleiding Bureau

Nieuwste handleidingen voor Bureau

Lian Li DK-05F Handleiding

10 December 2024

Fellowes 9870301 Handleiding

8 December 2024

Fellowes 9870701 Handleiding

8 December 2024

Fellowes 9871301 Handleiding

8 December 2024

Fellowes 9870001 Handleiding

8 December 2024

Fellowes 9871001 Handleiding

8 December 2024

Fellowes 9870101 Handleiding

8 December 2024

Fellowes 9870401 Handleiding

8 December 2024

Fellowes 9870201 Handleiding

8 December 2024

Fellowes 9870601 Handleiding

8 December 2024