Antennas Direct PA18 Handleiding


Lees hieronder de đź“– handleiding in het Nederlandse voor Antennas Direct PA18 (2 pagina's) in de categorie Signaalversterker TV. Deze handleiding was nuttig voor 45 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
Before attaching the antenna to any surface, TEST RECEPTION in that area.
Connect the antenna to the TV or receiver and run a full channel scan.
If reception is not as desired, move the antenna and rescan TV/receiver.
Q ck Start A ly/Install Instructionsui ssemb
PA18 UHF/VHF Antenna Pre-Amp Kit
Before beginning assembly, make sure all pieces needed are present.
1
2
3
4
1) Low noise amplifier
2) Loss loss power inserter
3) 2- 3’ coaxial cables
4) 12v DC power supply
The PA18 UHF/VHF Pre-Amp comes with:
Installation Instructions:
1. If your antenna is already installed, disconnect the down-lead coax cable from your antenna’s
transformer that runs to your digitalTV,TV/digital receiver or set-top box.
2. Connect the supplied 3’ coax cable to your (3)
antennas transformer as shown in Fig.1 (Your antenna
may look different but, the cable conntection will be the
same.) Connect the other end of the of the 3’ coax cable
to the PA18 amplifier using the “In” port as shown in(1)
the bottom of Fig.1
3. Strap the PA18 Pre-Amplifier to the antenna mast or to (1)
an adjacent wall in the attic installations using the supplied
cable tie.
4. Previous installation: Attach the down lead coax cable
that was attached to the antennas transformer to the “Out”
port of the PA18 Pre-Amplifier .(1)
Antenna Transformer
Fig.1
“In” Port “Out” Port
Technical Assistance is available Monday - Friday, 9am - 9pm Central Time
and Saturday - Sunday, 10am - 6pm.
©Antennas Direct 2012 02/12
PA18 Pre-Ampfilier
PI-012AP
TO RECEIVER
TO AMPLIFIER
POWER INSERTER
5. Install your down lead coax cable (not supplied) to the
“Antenna” input on the back of your digital TV,TV/digital receiver
or set-top box as shown in Fig. 3
6. Using the second supplied 3’ coax cable the left port labeled
“To Receiver” on the power inserter to your digitalTV,(2)
TV/digital receiver or set-top box. Do Not reverse the conection.
7. Connect the 12v DC power supply screw on f-connector (4)
to the bottom connection of the power inserter .(2)
8. Insert the wall plug into any 110 volt AC power sourse, wall
outlet or power strip, close to the TV and ensure that the 110v
wall outlet is live - not switched off.
For New Installation:
TO RECEIVER TO AMPLIFER
Fig.2
PA18 Pre-Amplifier
ANTENNA
INPUT
DIGITAL TELEVISION
DB2e HDTV Antenna
12v Power Supply
PI-012AP
TO RECEIVER
TO AMPLIFIER
Power Inserter
Finished Installation:
Your completed installation and assembly of your PA18 Pre-Amplifier should resemble the full installation diagram of Fig.3
Important: The power inserter sends power Up your down lead to drive the amplifier mounted on or near your antenna.
The power inserter can be located anywhere in your house but, is usually near your TV. The down lead coax cable
also brings the digital antenna into your house and the signal passes though the power inserter to your Digital TV/Receiver.
This eliminates any need for a 110VAC wall power source close to your antenna.
Fig.3
Technical Assistance is available Monday - Friday, 9am - 9pm Central Time
and Saturday - Sunday, 10am - 6pm.
©Antennas Direct 2012 02/12


Product specificaties

Merk: Antennas Direct
Categorie: Signaalversterker TV
Model: PA18
Kleur van het product: Black, Grey
Aansluiting(en): 75 Ohm F
Aantal poorten: 2
Geluid figuur: 1.8 dB

Heb je hulp nodig?

Als je hulp nodig hebt met Antennas Direct PA18 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Signaalversterker TV Antennas Direct

Handleiding Signaalversterker TV

Nieuwste handleidingen voor Signaalversterker TV