AMX MVP-WCS-52-GW Handleiding

AMX Oplader voor mobiel apparaat MVP-WCS-52-GW

Lees hieronder de 📖 handleiding in het Nederlandse voor AMX MVP-WCS-52-GW (2 pagina's) in de categorie Oplader voor mobiel apparaat. Deze handleiding was nuttig voor 50 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Installation Guide

MVP-WCS-52 Wall Charging Station

Overview

The optional MVP-WCS-52 Wall Charging Station (FG5966-1X) offers the same

recharging and connection features for the MVP-5200i Touch Panel as the

MVP-TCS-52 Table Charging Station, with the advantage of being placed within

accessible locations where the table station is either inconvenient or impractical

(FIG. 1).

The MVP-WCS-52 is available in white (FG5966-13) or black (FG5966-12).

The features of the MVP-WCS-52 include:

• Full charging of a docked MVP-5200i in approximately 4.5 hours

• Touch panel password feature for security

• Integrated docking alignment guides for easy docking

Specifications

The MVP-5200i touch panel remains locked in the MVP-WCS-52 until unlocked

by the user. This may be done by entering an appropriate password (please refer

to the MVP-5200i User Manual, available from www.amx.com, for more

information), or by pressing the Security Release button on the front of the

device in emergencies. The station ejects the MVP-5200i device top first

(FIG. 2).

The device uses two neodymium rare-earth magnets to secure the MVP-5200i to

the cradle when the touch panel is angled forward.

Unlocking the Touch Panel

Once placed within the Wall Charging Station, the MVP-5200i remains secured

until the user unlocks it. To release the touch panel from the Wall Charging

Station:

1. Press the Security Release button.

2. A password keypad will pop up on the MVP-5200i screen. Enter a

password in the password keypad and press Enter.

3. Wait for the Wall Charging Station to pivot the touch panel away from the

wall.

4. The device will remain in the ejected position until the MVP-5200i is

removed. Wait until the device’s ejection door has completely withdrawn

before re-installing the MVP-5200i.

Recharging

To recharge the MVP-5200i:

1. Slide the device into the Wall Charging Station cradle bottom-first and

make sure the device is fully seated in the Charging Station.

2. Press the top of the MVP-5200i back until it clicks. The touch panel is now

locked into the Charging Station, and the station will automatically charge

the device’s battery.

3. To release the touch panel, press the Security Release button, enter the

password (if activated), and wait for the Wall Charging Station to pivot the

touch panel away from the wall.

FIG. 1 MVP-WCS-52-GB Wall Charging Station - Front

MVP-WCS-52 Specifications

Dimensions (HWD): • 8.88" x 6.38" x 2.19" (22.54 cm x 16.19 cm x 5.56 cm)

Note: Always use the cutout/installation dimensions for

the MVP-WCS-52 when installing this unit into various

surfaces. This SP engineering drawing is available online

at www.amx.com.

Power Requirements: • 1.7A @ 12 VDC (Class II listed power supplemented)

Startup Power

Requirements: • Total: 1.7A

• Charging: 1.1A

• Ejection: 0.6A

Weight: • Without back box: 0.85 lbs (0.39 kg)

• With back box: 1.30 lbs (0.59 kg)

Front Panel

Components: • Securing Magnets: Secures MVP touch panel during

ejection.

• Security Latch: Adds the primary layer of security when

mounting an MVP touch panel. When the device is

inserted, this latch grabs onto the rear of the touch panel

and secures it to prevent it from inadvertently being

removed.

• Interface Connector Pins: A set of retractable pins (male)

that connect to the underside MVP connector strip. This

connection provides both communication and power

between the touch panel and the MVP-WCS-52.

• Support Cradle: This retractable mechanism supports a

resting MVP panel and allows a user to either insert or

remove a connected MVP panel.

• Security Release pushbutton: Located on the front of the

unit, this pushbutton toggles an on-screen security

keypad if security is enabled.

- Entering the correct release code allows the MVP-WCS-

52 to release the touch panel from the security latch.

Operating/Storage

Environments: • Operating Temperature: 0° C to 40° C (32° F to104° F)

• Operating Humidity: 20% - 85% RH

• Storage Temperature: -20° C to 60° C (-4° F to140° F)

• Storage Humidity: 5% - 85% RH

Security Release

MVP-5200i-GB

MVP-WCS-52

button

MVP-WCS-52 Specifications (Cont.)

Included

Accessories • MVP-WCS-52 Wall Charging Station Quick Start Guide

( )93-5966-12

• Wallmount Plastic Back Box (EMA5966-13)

• MVP-WCS-52 Installation Kit - Black (KA5966-01bl)

• MVP-WCS-52 Installation Kit - White (KA 5966-01wh)

• MVP-WCS-52 Wall Charging Station Template

( )68-5966-01

Other AMX

Equipment: • MVP-TCS-52 Table Charging Station (FG5966-1X)

• Wallmount Metal Rough-In Box (62-5966-12)

• PSN4.4 (FG423-45)

• PSN6.5 (FG423-41)

• MVP-5200i - Gloss Black (FG5966-01)

• MVP-5200i - Gloss White (FG5966-02)

FIG. 2 MVP-WCS-52-GW Wall Charging Station - Side View

MVP-5200i

Wall Charging Station

Security Release button

For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).

3/11

AMX reserves the right to alter specifications without notice at any time.

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com

93-5966-12 REV: F

Installing the MVP-WCS-52

Since the Wall Charging Station is intended to be affixed to a wall or other

permanent structure, care must be taken to ensure its proper installation to

prevent potential damage to the MVP-5200i placed within. The device may be

installed into existing walls, but the optional metal rough-in box must be

installed before installation of drywall or other paneling.

Note: Other than wall installation tools, the only tool required for this installation

is a #1 Phillips screwdriver.

Installing the Wall Charging Station and Plastic Back Box

The Plastic Back Box has two knockouts at the top of the box and four (4)

lockdown wings attached to the box with Phillips-head screws. For ease of

installation, the interior of the box contains an "UP" arrow pointing to the

knockouts.

Note: The optional Metal Rough-In Box is not required for installation of the

supplied Plastic Back Box, but it offers an extra level of support.

To install the Plastic Back Box:

1. Cut a hole into the wall or surface intended to hold the back box. The

back box is sized 8.375 inches (21.27cm) long and 5.75 inches (14.60cm)

high. Use the included MVP-WCS-52 Wall Charging Station Template

(68-5966-01) as an aid for hole placement and measurement.

WARNING: Make sure to measure the size of the intended hole before starting

to cut it. Cutting the hole slightly smaller than the dimensions to allow for

adjustments is highly recommended.

2. Select the knockout to be removed from the top of the back box. The box

has two knockouts, at the top left and the top right.

Note: To assist with wiring, and to avoid mechanical stresses on the wire and

the mechanism of the Wall Charging Station, the top right knockout is preferred

for use.

3. Run the power cable through the knockout into the back box. Pull out

about six inches (15.25cm) of cable into the back box to facilitate

installation of the MVP-WCS-52.

4. Slide the plastic back box into the hole, being careful not to twist or pinch

the cable, and set it flush with the wall. Make sure that all of the lockdown

wings are folded into their slots before attempting to insert the box. For

ease of installation, the inside of the box has the direction "UP" labeled for

reference.

5. Extend the wings on the sides of the back box by tightening the screws

inside the box, taking care not to overtighten. Not all of the wings must be

extended to lock the back box in place, but extending a minimum of two

wings on opposite sides of the box is highly recommended. Apply enough

pressure to the screw head to keep the box flush with the wall: this

ensures that the wing will tighten up against the inside of the wall.

WARNING: Make absolutely certain that the back box is in its intended

position. Once the back box lockdown wings are extended, removing the back

box will be extremely difficult without damaging the wall in the process.

6. Prepare the captive wires for the 2-pin 3.55 mm mini-captive wire

connector used for the MVP-WCS-52’s power supply:

• Strip 0.25 inch (6.35 mm) of wire insulation off all wires.

• Insert each wire into the appropriate opening on the connector.

• Turn the screws clockwise to secure the wires in the connector. Do not

over-torque the screws; doing so can bend the seating pins and damage

the connector.

7. Secure the power cable to the device, using either of the two tie-wrap

anchors included in the Installation Kit at the top rear of the device

(FIG. 3). Point the head of each tie wrap toward the center of the device.

8. Firmly seat the mini-captive wire connector to the power connector on the

device.

9. Firmly seat the device against the back box. Make sure that the tab con-

nector at the top of the device is locked into the back box.

10. Insert the two installation screws from the MVP-WCS-52 Installation Kit

into the screw holes in the interior compartment of the device and tighten

them to anchor the device to the back box.

Note: For ease of installation, put each screw on a neodymium magnet in the

device’s interior compartment to keep them on hand until they are needed.

11. Take a rubber foot and remove its adhesive backing. Put the foot, adhe-

sive-side down, in the slot surrounding the screw hole in the Wall Charg-

ing Station. Press down firmly to remove any air bubbles from underneath

the foot.

12. Install an MVP-5200i device by placing it into the interior compartment

bottom-first. Press the top of the touch panel until it is flush with the Wall

Charging Station. The neodymium magnets will hold it in place.

13. To remove the MVP-5200i, unlock the touch panel and wait for the touch

panel to pull away from the Wall Charging Station. Once it has been

released, grip it by the top of the device, and pull it free from the Charging

Station.

Installing the Optional Metal Rough-In Box

The optional Metal Rough-In Box (FG037-11) is 10 inches (25.40cm) wide at its

widest dimension (wider than the bezel of the Wall Charging Station), and is

only intended for pre construction installations (FIG. 4). The Metal Rough-In

Box is used in conjunction with the Wall Charging Station’s plastic back box.

The Metal Rough-In Box must be located behind 3/8" (0.95cm) to 3/4" (1.91cm)

of wall/mounting surface material.

The Metal Rough-In Box bears a wing on each corner which is intended to

bridge gaps between studs and/or spacers. These wings may be bent carefully

in order to fit a particular gap, but may not be so bent as to allow the rough-in

box to hang in a vertical position. Once placed in the desired position, put at

least one screw through each wing into the adjoining stud or spacer to secure

it.

The interior of the rough-in box contains a set of holes on either side, as well as

top and bottom, for standard 1/4-inch screws. Use these holes to anchor the

rough-in box to its adjoining studs or spacers.

WARNING: Ensure that the metal rough-in box is flush with the 2x4 studs. Any

overhang will affect the installation of the covering sheetrock, as well as affect

the placement of the plastic back box.

The rough-in box has two sets of knockouts in the top and bottom, one in the

set for US wiring and one for international wiring.

Note: Make sure that the power cable has been pulled through the metal

rough-in box by the resident electrician before continuing the installation.

After completing the installation of the metal rough-in box, install sheet rock or

other wall material over the box, cut a hole matching the size of the inside

diameter in the sheet rock, and clean out all dust before proceeding with the

installation of the Wall Charging Station.

Additional Information

For additional installation information, please refer to the MVP-5200i Modero

ViewPoint Touch Panel User Manual, available online at www.amx.com.

FIG. 3 MVP-WCS-52 - Rear View Of Anchors And Connector Plug

FIG. 4 Typical Optional Metal Rough-In Box Installation

Tie-Wrap Anchors

Mini-Captive Wire

Connector Plug

(female)

Install front surface of rough-in

box flush with surface of wall stud

Product specificaties

Merk:	AMX
Categorie:	Oplader voor mobiel apparaat
Model:	MVP-WCS-52-GW
Kleur van het product:	Zwart
Gewicht:	590 g
Breedte:	161.9 mm
Diepte:	55.6 mm
Hoogte:	225.4 mm
Type stroombron:	AC
Ingangsspanning:	12 V
Ingebouwde accu:	Nee
Compatibiliteit:	MVP-5200i\r\nMVP-5150\r\nMVP-5100
Type oplader:	Binnen
Lader compatibiliteit:	Tablet
Bedrijfstemperatuur (T-T):	0 - 40 °C