AMX FG552-28 Handleiding

AMX AV extender FG552-28

Lees hieronder de 📖 handleiding in het Nederlandse voor AMX FG552-28 (2 pagina's) in de categorie AV extender. Deze handleiding was nuttig voor 29 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Quick Start Guide

HPX-AV101-DP-R DisplayPort Module with Retractable Cable

Overview

Hydraport Retractable Cable Modules are designed to be used in conjunction

with the HPX-600/900/1200 Connection Port base assembly, to provide the

convenience of various types of cables in a Hydraport System.

The HPX-AV101-DP-R DisplayPort Module with Retractable Cable (FG552-28)

provides a user-accessible Display cable in a retractable spool that mounts into

the Hydraport base assembly (FIG. 1).

The HPX-AV101-DP-R features Dual Mode DisplayPort (DP++) compatibility.

Installation

Warning! - Do not attempt to open the retractable cable module enclosure.

There are no serviceable parts inside the module.

Opening the module enclosure may result in an uncontrolled release of spring

forces which could cause serious injury and/or equipment damage.

Opening the module enclosure will void the product warranty.

Caution: Only use a hand-held screw driver for the mounting instructions in this

document. Over-tightening the screws can hinder performance or damage the

product.

1. For Existing HPX Installations, First Unmount the HPX Base

For new HPX installations, skip to Step 2.

For existing HPX installations, the HPX Base Assembly must be un-mounted

from the surface before the Retractable Cable Modules can be installed:

1. Cut/remove any cable ties that would restrict the removal of the HPX Base

Assembly.

2. Loosen the four mounting screws (located inside and at each end of the

HPX base assembly), in order to rotate the retaining tabs from under the

mounting surface.

Note that when the cover of the HPX base is open, only two of these

screws are visible. To access the other two mounting screws, tip the cover

over to the opposite open position (see FIG. 2).

3. Once the retaining tabs have been rotated out from under the mounting

surface, the HPX assembly can be be lifted away from the mounting

surface.

FIG. 3 provides a cutaway view of the End Cap, showing the retaining tabs

in both the loose position and the tightened (secure) position:

2. Remove the End Cap and Existing Modules

Remove the End Cap as well as existing modules (as necessary, depending on

how you want the modules arranged) from one end of the HPX base assembly.

1. Remove the (silver) pivot screw and pivot pawl assembly in the center of

the End Cap (FIG. 4).

2. Remove the six (black) sheet metal screws that secure the End Cap to the

HPX assembly (locations circled in red below).

3. Gently slide the End Cap out of the HPX base assembly.

FIG. 1 HPX-AV101-DP-R DisplayPort Module with Retractable Cable

FIG. 2 HPX Base Assembly (shown mounted) - Mounting Screws Locations

FIG. 3 HPX Base Assembly (shown mounted) - Mounting Screws Locations

FIG. 4 HPX Base Assembly (shown mounted) - Mounting/Pivot Screw Locations

For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).

1/14

AMX reserves the right to alter specifications without notice at any time.

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com

93-0552-28 REV: C

3. Insert the Retractable Cable Module into the HPX Base

1. Orient the module relative to the HPX base assembly so that the Module’s

faceplate is facing up, towards the mounting surface (FIG. 5).

2. Align the Mounting Notches on the module with the Mounting Rails on the

HPX base.

Note: Module faceplates are notched in a “tongue and groove" type fashion to

ensure that all modules are oriented correctly in the HPX. Note the orientation of

the notched faceplate on each module before sliding the module(s) into the HPX

assembly.

3. Slide the module into position.

4. Install any remaining modules into the HPX base.

4. Re-Install the End-Cap

Caution: Do not use a high-powered torque screw driver. Over-tightening these

screws can damage the product.

1. Align the Mounting Notches on the End Cap with the Mounting Rails on the

HPX base.

2. Slide the End Cap into the HPX base until it is fully inserted against the end

of the base assembly.

3. Secure the End Cap with the six (black) sheet metal screws (removed in

Step 2 - 2; see FIG. 4).

4. Replace the (silver) pivot screw and pivot pawl assembly (removed in Step

2 - 1, see FIG. 4) in the center of the End Cap.

5. Mount the HPX into the Mounting Surface

Caution: Do not use a high-powered torque screw driver. Over-tightening these

screws can damage the product.

Note: For detailed instructions on installing the HPX base assembly, refer to the

HPX-600/900/1200 Installation Guide (available online at www.amx.com).

1. Carefully insert the HPX base into the cutout in the mounting surface.

2. Tighten the four mounting screws (loosened in Step 1, see FIG. 3) located

inside and at each end of the HPX base assembly, to rotate the retaining

tabs into locking position under the mounting surface.

6. Terminate Fixed Cables

1. Terminate fixed cables as necessary.

Note: Use of an extension cable on either end of this cable should be

avoided to ensure optimal performance.

2. Replace any cable ties that were removed in Step 1.

Mounting Dimensions

FIG. 6 provides dimensions for the retractable cable module, when installed in

an HPX base assembly:

Additional Documentation

Refer to the Products > Architectural Connectivity catalog page on

www.amx.com (Dealer Site) for additional product documentation.

FIG. 5 Retractable Cable Module - Mounting into an HPX Base Assembly

FIG. 6 RCM Module (installed in an HPX base) - detailed dimensions

4.65”

(11.81 cm)

End Cap

8.51”

(21.62 cm)

(of Base Assembly)

Product specificaties

Merk:	AMX
Categorie:	AV extender
Model:	FG552-28
Kleur van het product:	Zwart
Gewicht:	453 g
Ondersteunde video-modi:	1080p
Maximum resolutie:	1920 x 1080 Pixels
Video-ingang:	1
Compatibele producten:	AMX HydraPort
HDMI in:	1
Video uit:	1
Bandbreedte:	10.2 Gbit/s
Aansluiting type:	DisplayPort (M), HDMI (M)