AMX AVB-TX-CATPRO-HD15-5T Handleiding

AMX AV extender AVB-TX-CATPRO-HD15-5T

Lees hieronder de 📖 handleiding in het Nederlandse voor AMX AVB-TX-CATPRO-HD15-5T (2 pagina's) in de categorie AV extender. Deze handleiding was nuttig voor 20 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Quick Start Guide

AutoPatch CatPro RGBHV+Stereo Modules

Overview

CatPro RGBHV+Stereo Transmitter (TX) and Receiver (RX) Modules work together

or work in conjunction with CatPro RGBHV+Stereo boards on an AMX AutoPatch

Distribution Matrix. This guide contains complete information for standalone use.

For use with a distribution matrix, see the distribution matrix’s instruction manual on

the AMX AutoPatch CD or at www.amx.com.

Specifications

* The automatically adjusting universal 110/220 IEC power supply is ENERGY STAR

® qualified to

ensure maximum efficiency and savings.

Module Installation

Module Mounting Options

Rack Trays and Mounting Brackets – Search for ”V Style” at www.amx.com.

Important: Always use a UL approved power source. Check the power source’s

documentation for information specific to that power source.

System Setup

A typical setup using CatPro RGBHV+Stereo TX and RX Modules is illustrated in

FIG. 2. The signals are sent to a monitor with speakers at a distance, as well as to a

local monitor with speakers.

FIG. 1 CatPro RGBHV+Stereo TX and RX Modules

General Specifications – TX (FG1010-45-01) and RX (FG1010-48-01)

Power Consumption (max.) 12 V to 24 V DC @ 6 W

Thermal Dissipation (max.) 20 BTU/hr.

Power Connector 2.1 mm DC power jack (power supply provided*)

Humidity 0 to 90% non-condensing

Operational Temperature 32° to 110° F (0° to 43° C)

Dimensions TX Module 5.15 in. (13.08 cm) depth

5.80 in. (14.73 cm) width

1.66 in. (4.22 cm) height

Weight TX Module Approximately 1.5 lb. (0.68 kg)

Dimensions RX Module 5.15 in. (13.08 cm) depth

4.33 in. (11.00 cm) width

1.66 in. (4.22 cm) height

Weight RX Module Approximately 1.3 lb. (0.6 kg)

Supported Twisted-Pair

Cable Types

Category cable 5, 5e, 6, 6e, and STP (skew free cable is not

recommended)

Note: All measurements listed were taken using Cat5e cable.

Approvals CE, UL, cUL, RoHS

Specifications – TX (FG1010-45-01)

Signal Types RGBHV + Stereo Audio

Maximum Resolution 1600x1200 (4:3) and 1920x1080p (16:9) @ 60 Hz

up to 1000 ft. (305 m)

RGB In

Signal Level Range:

Impedance:

Return Loss:

+0.75 V to -0.3 V (terminated)

75 ohms

<-35 dB @ 5 MHz

RGB Local Out

Signal Level Range:

Impedance:

SNR:

+0.75 V to -0.3 V (terminated)

75 ohms

>65 dB

Sync In

Impedance:

Polarity:

510 ohms

Active high or low

Sync Local Out

Signal Level:

Polarity:

Low = 0 V, High = +5 V (unterminated)

Active high or low (follows input polarity)

Audio In

Signal Type:

Signal Levels (max.):

Impedance:

Stereo, unbalanced

+8 dBu

2 kohms

Audio Local Out

Signal Type:

Signal Levels (max.):

Frequency Response:

THD+N:

SNR:

Impedance:

Stereo, unbalanced

+8 dBu (unity gain)

<±0.35 dB, 20 Hz to 20 kHz

<0.04%, 1 kHz, -10 dBu to +4 dBu

>105 dB, 20 Hz to 20 kHz, Vin = +4 dBu

<5 ohms

Connectors

RGBHV In:

RGBHV Local Out:

Stereo Audio In:

Stereo Audio Local Out:

RGBHV+Stereo Out:

1 Female HD-15

1 Female 3.5 mm mini-stereo jack

1 Female RJ-45

CatPro RGBHV+Stereo TX Module

FG1010-45-01

CatPro RGBHV+Stereo RX Module

FG1010-48-01

Front view

Rear view

EDID Specifications – TX (FG1010-45-01)

Standard Timing Identification

ID 1 1600x1200 @ 60 Hz (This is the preferred timing identified in the EDID)

ID 4 1280x1024 @ 85 Hz

ID 6 1152x864 @ 120 Hz

ID 8 1280x800 @ 60 Hz

ID 7 1280x720 @ 60 Hz

ID 3 1024x768 @ 120 Hz

ID 5 800x600 @ 120 Hz

ID 2 640x480 @ 120 Hz

Established Timing

720x400 @ 70 Hz, 88 Hz

640x480 @ 60 Hz, 67 Hz, 72 Hz, 75 Hz

800x600 @ 56 Hz, 60 Hz, 72 Hz, 75 Hz

832x624 @ 75 Hz

1024x768 @ 60 Hz, 70 Hz, 75 Hz, 87 Hz

1280x1024 @ 75 Hz

1152x870 @ 75 Hz

Specifications – RX (FG1010-48-01)

Signal Types RGBHV + Stereo Audio

Maximum Resolution 1600x1200 (4:3) and 1920x1080p (16:9) @ 60 Hz

up to 1000 ft. (305 m)

RGB Out (at 1000 ft.)

Signal Level Range:

Impedance:

SNR:

Skew Adjustment:

+0.75 V to -0.3 V typical (terminated, user adjustable with gain & peak)

75 ohms

>50 dB

0 to 62 ns in 2 ns increments on RGB channels

(user adjustable)

Sync Out

Signal Levels:

Polarity:

Low = 0 V, High = +5 V (unterminated)

Active high or low (follows input polarity)

Audio Out (at 1000 ft.)

Signal Type:

Signal Levels (max.):

Volume Control Range:

Frequency Response:

THD+N:

SNR:

Impedance:

Stereo, unbalanced

+8 dBu

Mute to +6 dB (user adjustable)

<±0.2 dB, 20 Hz to 20 kHz

<0.04%, 1 kHz, -10 dBu to +4 dBu

>105 dB, 20 Hz to 20 kHz, Vin = +4 dBu

<5 ohms

Connectors

RGBHV+Stereo In:

RGBHV Out:

Stereo Audio Out:

1 Female RJ-45

1 Female HD-15

1 Pluggable 3.5 mm terminal block

FIG. 2 Typical system setup using CatPro Modules

TX# FG1010-45-01

RX# FG1010-48-01

Source PC

Local monitor

with speakers

Distance monitor

with speakers

Note: When used with an AMX

AutoPatch Distribution Matrix,

overall cable length cannot exceed

1,000 ft. (305 m).

For full warranty information, refer to www.amx.com.

2/11

AMX reserves the right to alter specifications without notice at any time.

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com

93-10-828-01 REV: B

CatPro RGBHV+Stereo Modules use power supplies provided with each unit.

To attach source device connectors and power to the TX Module:

1. Insert the audio mini-jack (3.5 mm) and the HD-15 connector into the Audio

and the Video Input connectors.

2. Insert the RJ-45 connector into the CAT-5 receptacle.

3. Plug the desktop power supply into the power jack on the module and into an

AC external power source.

If you are providing the power supply – Plug the power cord from a UL

(or equivalent) listed power supply into the power jack on the Module.

The electrical ratings must meet those indicated in the Specifications table.

4. Optional – To use the Local Out option, insert the audio mini-jack and the

HD-15 connector into the Local Output connectors.

To attach destination device connectors and power to the RX Module:

1. Insert the HD-15 connector and wire the audio connector (wiring shown is for

an unbalanced output signal).

2. Insert the RJ-45 connector into the CAT-5 receptacle.

3. Plug the power cord into the power jack and into the power source.

If you are providing the power supply – Plug the power cord from a UL

(or equivalent) listed power supply into the power jack on the Module.

The electrical ratings must meet those indicated in the Specifications table.

4. If the destination display needs adjusting, see “Adjusting the Picture” below.

TX and RX HD-15 Pinouts

Note: 55 mA supplied on output pin 9; power draw not to exceed 50 mA per port.

Adjusting the Picture

This section includes information for adjusting the gain, peak, and skew to obtain a

sharp picture on the destination display. Volume can also be adjusted during the

procedure for adjusting skew.

Tip for Flat Panel LCDs: For optimal results, press the auto-adjust button on the

flat panel LCD after using the adjustment options on the RX Module.

Test Image File

Test image files are provided on the AMX AutoPatch CD. File names begin with the

resolution (800x600, 1024x768, 1280x768, etc.) and end with “SkewPattern.”

• Turn the peak and gain potentiometers (watch the black and white pattern and

the text) before and after skew adjustment for brightness and sharpness.

• Turn the Adjust knob for each color until the corresponding color bars align with

the color bars directly below them.

Gain and Peak

Gain and peak potentiometers on the RX can be used to compensate for overall

cable length.

Important: Do not push or over-tighten the potentiometers when turning them.

To adjust the gain and peak:

1. Optional – On the PC, open the test image file for the resolution of the source

signal.

2. If the picture’s brightness needs to be increased or decreased, turn the Gain

potentiometer.

3. If the picture is not sharp enough, turn the Peak potentiometer. (Increasing the

peak removes graininess.)

4. Repeat Steps 2 and 3 after adjusting the skew according to the steps below.

Skew and Volume

The adjust knob on the RX Module can be used to compensate for skew inherent in

UTP cable by adjusting the skew of the video signals. The knob also adjusts the

volume. A small screwdriver works well for turning and pressing the knob. The knob

does not have a mechanical start or stop point. If the LED blinks when the knob is

turned, the setting has reached its minimum or maximum point.

The RX Module ships with factory-defined default settings of “no-skew delay” for the

skew on R, G, and B and to “unity gain” on the volume. Once the adjustment process

has been successfully completed and saved, the new settings replace the factory-

defined settings. The system will restore the new settings whenever power is cycled.

To abort the adjustment procedure at any time, hold the Adjust knob down until the

LED blinks 3 times and the RX Module reverts to its previous settings. Cycling power

on the module during the adjustment procedure will have the same effect. The

individual settings are not stored in memory until all adjustments (Steps 2-10 below)

have been made.

To adjust the skew and volume:

1. Optional – Open the test image file on the PC.

2. Press the Adjust knob.

The LED turns red, and the module is placed in Red Skew Adjust mode.

3. Turn the Adjust knob clockwise or counter-clockwise.

The red color component shifts right or left.

4. Press the Adjust knob.

The LED turns green, and the module is placed in Green Skew Adjust mode.

5. Turn the Adjust knob clockwise or counter-clockwise.

The green color component shifts right or left.

6. Press the Adjust knob.

The LED turns blue, and the module is placed in Blue Skew Adjust mode.

7. Turn the Adjust knob clockwise or counter-clockwise.

The blue color component shifts right or left.

8. Press the Adjust knob.

The LED turns white, and the module is placed in Volume Adjust mode.

9. Turn the Adjust knob clockwise to increase volume or counter-clockwise to

decrease volume.

10. Press the Adjust knob.

The LED turns off, and the module saves all of the settings.

If the LED alternately blinks red and green, see “Troubleshooting” below.

Tip: To adjust the volume without changing the skew settings, press the Adjust knob

until the LED turns white and then complete Steps 9 and 10 above.

Troubleshooting

LED Blinks Red and Green

• If the LED alternately blinks red and green, a configuration failure has

occurred.

• If the blinking happens when the Adjust knob is pressed to save (see

Step 10 in the skew adjustment procedure above), the system failed to save

the settings. Any adjustments just made are still in effect, but will be lost the

next time power is cycled.

To save the adjustments, repeat Steps 2, 4, 6, 8, and 10 (i.e., cycle the colors

until the LED turns off).

If the blinking happens when power is cycled, the system could not find valid settings

and reverted to the factory-defined default settings. Complete Steps 2 through 10

again.

FIG. 3 Attach source device connectors, RJ-45 connector, and power to TX

FIG. 4 Attach destination device connectors and power to RX

FIG. 5 Connector pinouts for HD-15 TX In and for TX and RX Out

FIG. 6 Test Image file

Power HD-15 RJ-45

Audio

Power

RJ-45

Audio HD-15

Audio wiring

Black and white pattern

Sample text

Color bars

Product specificaties

Merk:	AMX
Categorie:	AV extender
Model:	AVB-TX-CATPRO-HD15-5T
Kleur van het product:	Zwart
Gewicht:	0.68 g
Soort:	AV-zender
LED-indicatoren:	Ja
Bluetooth:	Nee
Connectiviteitstechnologie:	Bedraad
Maximum resolutie:	1920 x 1080 Pixels
VGA (D-Sub)poort(en):	2
Aansluiting voor netstroomadapter:	Ja
Audio-ingangen:	1
Audio-uitgang:	1
Ondersteunde grafische resoluties:	720 x 400,832 x 624,1152 x 870,1024 x 768 (XGA),1152 x 864 (XGA+),1280 x 1024 (SXGA),1280 x 720 (HD 720),1280 x 800 (WXGA),1600 x 1200 (UXGA),640 x 480 (VGA),800 x 600 (SVGA)
VGA (D-Sub) invoer ports:	1
RJ-45 uitgang ports:	1
Afmetingen (B x D x H):	147.3 x 130.8 x 42.2 mm
VGA (D-Sub) uitgang ports:	1
Wifi:	Nee
Stroomverbruik (typisch):	6 W
Bedrijfstemperatuur (T-T):	0 - 43 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 90 procent
Ondersteundende kabel types:	Cat5, Cat5e, Cat6, Cat6e