AMX CB-MXP10 Handleiding

AMX Flat panel steun CB-MXP10

Lees hieronder de 📖 handleiding in het Nederlandse voor AMX CB-MXP10 (2 pagina's) in de categorie Flat panel steun. Deze handleiding was nuttig voor 42 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Installation Guide

CB-MXP10 Rough-In Box and Cover Plate for Modero X 10” Panel

Overview

The CB-MXP10 Rough-In Box (FG039-17) is an optional accessory for the Modero X

Series 10” Wall Mount Touch Panel. It allows the panel to be mounted directly to the

studs/pre-wall.

The back of the Modero X Series 10” Wall Mount Touch Panel is contained within a

plastic outer housing or back box, and the back box attaches to the Rough-In Box. The

Rough-In Box kit includes a wall box, cover, and mounting screws.

Specifications

WARNING: In order to guarantee a stable installation of the touch panel, the distance

between the CB-MXP10 and the outer wall surface must be a minimum of .50 inches

(1.27cm) and a maximum of .1.50 inches (3.81cm).

• Refer to the 95-5968-34 diagram for detailed installation dimensions.

Pre-Wall Installation of the CB-MXP10 Rough-In Box

1. Remove the rough-in box cover (B in FIG. 1) before installation of the Rough-In

Box (A). Note: the cover MUST be removed before drywall installation. The

cover may be reinstalled after drywall installation using 4-40 screws (not

included).

2. Fasten the CB-MXP10 rough-in box to the stud through the holes on the Stud

Mounting tabs, using either nails or screws (not provided).

3. Additional framing or blocking may be desired for a more robust mounting.

4. Remove the appropriate wiring knockouts from the rough-in box to 

accommodate the cables being threaded through to the 19” or 20” Wall Mount

Touch Panel.

5. Thread the incoming Ethernet and USB wiring through the knockouts. Using the

left wiring knockouts for USB connector cables and the right wiring knockouts for

the LAN/PoE In cable is very highly recommended with this installation. Leave

enough slack in the wiring to accommodate installation of the docking station.

6. Install the drywall/sheetrock before inserting the back box for the CB-MXP10.

7. Cut out the opening for the Wall Mount Touch Panel back box where the wall has

been placed over the Rough-In Box. Cutting out the surface slightly smaller than

what is outlined in the installation drawings, so that you can make any necessary

cutout adjustments, is very highly recommended.

NOTE: The front cover of the CB-MXP10 (B in FIG. 1) should be installed after the

appropriate wiring is pulled to the Rough-In Box. The cover should then be removed

prior to the installation of the touch panel back box and discarded.

FIG. 1 CB-MXP10 Rough-In Box - with front cover

8.65”

(21.98 cm)

8.94”

(22.71 cm)

5.78”

(14.68 cm)

Rough-In Box

Rough-In Box With Cover

Cover

CB-MXP10 (FG039-17) Specifications

Dimensions (HWD) • Rough-In Box: 8 5/8" x 9 7/8" x 2 1/4" (22.0 cm x 22.7 cm x

5.7 cm)

• Rough-In Box Cover Plate: TBD

Weight • With cover: TBD

• Without cover: 1.80 lbs (0.82 kg)

Certifications • UL Listed

Included 

Accessories: • Cover Plate for Rough-in Box (FG039-20)

• Back Box to Rough-In Box Mounting Screws (4) 

( )80-5967-03

• Cover Plate to Rough-In Box Mounting Screws (4) 

( )80-5967-03

Recommended

Wall Cutout

for the CB-MXP10

5.5”

(13.97 cm)

8.75”

(22.23 cm)

For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).

4/12

AMX reserves the right to alter specifications without notice at any time.

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com

93-0039-17 REV: B

Cover

CB-MXP10

Rough-In Box

Without Cover

CB-MXP10

Rough-In Box

With Cover

(oblique angle)

Knock-outs

Front

(oblique angle)

Cover screws

2.24”

(5.68 cm)

8.94”

(22.71 cm)

2.24”

(5.68 cm)

5.78”

(14.68 cm)

2.39”

(6.08 cm)

6.48”

(16.6 cm)

2.39”

(6.08 cm)

8.94”

(22.71 cm)

Front

Product specificaties

Merk:	AMX
Categorie:	Flat panel steun
Model:	CB-MXP10
Kleur van het product:	Zilver
Breedte:	227 mm
Diepte:	57 mm
Hoogte:	220 mm
Montagewijze:	Muur
Maximale gewichtscapaciteit:	- kg
Certificering:	cTUVus, UL
Paneelmontage-interface:	- mm
Maximale schermgrootte:	10 "
Minimale schermgrootte:	- "