Altronix NetWay8 Handleiding

Altronix Netwerkkaart/adapter NetWay8

Lees hieronder de 📖 handleiding in het Nederlandse voor Altronix NetWay8 (8 pagina's) in de categorie Netwerkkaart/adapter. Deze handleiding was nuttig voor 65 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

Power over the Ethernet

PoE Solution for Standard

Network Infrastructure

Installation Guide

Models Include:

NetWay8 NetWay16

- Eight (8) Port PoE Midspan Injector - Sixteen (16) Port PoE Midspan Injector

DOC#: NET

Rev. 052110 More than just power.™

- 2 - NetWay8/NetWay16

Overview:

Altronix NetWay8/NetWay16 Midspans provide power and pass data for PoE and PoE+ compliant cameras/edge devices.

Cameras/edge devices may be located up to 100m from the NetWay unit. A NetWayXT (PoE) or NetWayXTX (PoE+) re-

peater module can be utilized to extend the distance an additional 100m for a total range of up to 200m. A maximum range

of 600m is possible using multiple repeaters, based on camera/device port requirement. NetWay Midspans are capable of

supporting non-PoE compliant fixed and PTZ IP cameras utilizing NetWay1512 or NetWay3012 adapters.

NetWay Specifications:

Common Specifications:

Installation Instructions:

Wiring methods shall be in accordance with the National Electrical Code (ANSI/NFPA70), local codes, and the authori-

ties having jurisdiction. These products are for indoor use only and must be installed within the protected premises.

NetWay units should be serviced by authorized personnel. Replace all fuses with same type and rating (4A/250V).

Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of

the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equip-

ment in an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer.

Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow required for safe

operation of the equipment is not compromised

Mechanical Loading - Mounting of the equipment in the rack should be such that a hazardous condition is not achieved

due to uneven mechanical loading.

Circuit Overloading - Consideration should be given to the connection of the equipment to supply circuit and the effect

that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate consideration of

equipment nameplate rating should be used when addressing this concern.

Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be

given to supply connections other than direct connections to the branch circuit (e.g. use of power strips).

NetWay is not intended to be connected to outside plant leads.

1. Attach mounting brackets to NetWay unit for rack installation (Fig. 7, pg. 7).

Affix rubber pads to NetWay for shelf installation (Fig. 8, pg. 7).

2. Secure the unit in a rack or place unit on a shelf as desired.

The following factors should be taken into consideration when installing these rack mount units:Note:

a. The unit is to be installed in a space where the maximum ambient temperature does not exceed 104ºF (40ºC).

b. Take care to insure there is sufficient air flow around the unit and that obstructions do not impede it.

c. When mounting units in rack, take care to avoid uneven loading which can cause a hazardous condition.

3. Set illuminated master power disconnect circuit breaker to the (OFF) position .(Fig. 1d, pg. 3)

4. Plug the grounded AC line cord (included) into the IEC 320 connector of the NetWay unit

. Plug unit into a reliable earth grounded socket. When using multiple units the sum of the individual (Fig. 1e, pg. 3)

name plate ratings should not exceed the supply circuit rating. Do not connect to a receptacle controlled by a switch.

5. Connect structured cables from port marked [IN] on NetWay to the corresponding inputs of an ethernet switch or

video server .(Fig. 1b, pg. 3, Fig. 5, pg. 5)

Agency Listings:

• UL/CUL Listed for Information Technology Equipment

(UL 60950-1).

• CE approved.

Power:

• Unit supplies PoE output voltage (55V), and up to

30W max. full power per port.

Total power: NetWay8 - 150W, NetWay16 - 300W.

• IEEE 802.3af (PoE) and IEEE 802.3at (PoE+) compliant.

• All output circuits are power-limited.

• Short circuit protection.

Functions:

• Auto detection and protection of legacy

non-PoE cameras/edge devices.

Features:

• Illuminated master power disconnect circuit breaker

with manual reset (switch).

• Individual port status LEDs.

Features :(cont’d)

• IEC 320 - 3-wire grounded line cord (detachable).

• Unit can be rack or shelf mounted.

• 1U rack mount chassis for use in standard EIA 19” rack.

Accessories:

NetWay1512:

• 15W adapter for non-PoE compliant IP cameras.

(For UL 60950-1 applications only).

NetWay3012:

• 25W adapter for non-PoE compliant IP

fixed or PTZ cameras.

(For UL 60950-1 applications only).

NetWayXT:

• PoE repeater module extends range 100m

(For UL 60950-1 applications only).

NetWayXTX:

• PoE+ repeater module extends range 100m

(For UL 60950-1 applications only).

NetWay8:

• Eight (8) ports of cameras/edge devices over ethernet

(CAT5) cable up to a distance of 100m per port.

NetWay16:

• Sixteen (16) ports of cameras/edge devices over ethernet

(CAT5) cable up to a distance of 100m per port.

NetWay8/NetWay16 - 3 -

All cabling and wire must be UL Listed and/or Recognized wire suitable for their application.Note:

6. Connect structured cables from port marked [OUT] on NetWay to PoE compliant camera/edge

devices (Fig. 1a, pg. 3, Fig. 5, pg. 5).

For UL294 applications, the products are to be tested as part of a complete Access Control System and in Note:

accordance with UL Listed Access Control Devices.

All interconnected devices must be UL Listed.Note:

7. Upon completion of wiring set illuminated master power disconnect circuit breaker to the RESET (ON)

position (Fig. 1d, pg. 3).

8. Port status LEDs on the NetWay will initialize when PoE devices are connected as follows:

- LED will illuminate when devices are IEEE 802.3af compliant.

- LED will blink once and illuminate when devices are IEEE 802.3at compliant (PoE+).

Port Status and LED Flash Codes:

Port Status Flash Codes Description

All Ports Off Sequential LED Port Scan No devices connected

Port Off OFF LED OFF

Port On ON LED ON

Class 4 detection Port Blinks 2 times Enables power to PoE devices.

Non-compliant Device 2Hz Will prevent port from turning on.

Port Overload Fault 5Hz Will prevent port from turning on.

4 Port Overload Grouped 5Hz 4 LEDs

Will prevent ports from turning on.

8 Port Overload Grouped 5Hz LED’s 1-8 Power Supply Overload for ports 1-8.

LED’s 9-16 Power Supply Overload for ports 9-16.

Fig. 1

1a OUT 1-8 (NetWay8), OUT 1-16 (NetWay16): Structured cable to PoE compliant cameras/edge devices.

1b IN 1-8 (NetWay8), IN 1-16 (NetWay16): Structured cable to ethernet switch or video server.

1c LED(s) 1-8 (NetWay8), 1-16 (NetWay16): Port status LEDs.

1d Illuminated master power disconnect circuit breaker (switch):

• OFF position Circuit breaker tripped Switch not illuminated.

• RESET (ON) position Switch illuminated.

1e IEC 320 Connector: 115VAC 60Hz (grounded line cord included).

AC POWER

NetWay8 & Net y16 - Rear PWa anel

NetWay8 - Front Panel

NetWay16 - Front Panel

1a 1c1b

1d 1e

Product specificaties

Merk:	Altronix
Categorie:	Netwerkkaart/adapter
Model:	NetWay8
Gewicht:	2889 g
LED-indicatoren:	Ja
Stroom:	3 A
Aantal Ethernet LAN (RJ-45)-poorten:	8
Certificering:	UL 60950-1\nCE
Voldoet aan industriestandaarden:	IEEE 802.3af, IEEE 802.3at
Ingangsspanning:	115 V
Frequentie:	60 Hz
Rack-montage:	Ja
Maat:	19 "
Power over Ethernet (PoE):	Ja
Afmetingen (B x D x H):	486 x 216 x 42 mm
Rackcapaciteit:	1U
Stroom via Ethernet (PoE):	- V