Alto TS115W Handleiding

Alto Niet gecategoriseerd TS115W

Lees hieronder de 📖 handleiding in het Nederlandse voor Alto TS115W (20 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 36 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/20

QUICKSTART GUIDE

ENGLISH

GUÍA DE INICIO RÁPIDO

ESPAÑOL

GUIDE D'UTILISATION RAPIDE

FRANÇAIS

GUIDA RAPIDA

ITALIANO

SCHNELLSTART-ANLEITUNG

DEUTSCH

SNELSTARTGIDS

NEDERLANDS

www.a ltoprofess ional.com/wireles swww.a ltoprofess ional.com/wireles s

BOX CONTENTS

• Truesonic Wireless speaker

• Power cable

• Quickstart Guide

• Safety Instructions & Warranty Information Booklet

INSTALLATION

This speaker should be installed on a stand on the

floor, according to its maximum weight, or suspended

from its suspension points (M10 x 1.5PH, 30mm

length) (see example image). We do NOT recommend

suspending multiple speakers in a vertical array.

CONNECTION DIAGRAM

*Note: Microphones, mixer, and cables are not included. Second Truesonic Wireless

speaker sold separately.

Mixer*

Power

Microphones*

Speaker Speaker*

This diagram is a suggestion for setting up the speaker with audio connections. To pair

the speaker with a Bluetooth™ device, see the BLUETOOTH PAIRING & LINKING

section below.

Eyebolt

Dust cover

Suspension

point

Example:

BLUETOOTH PAIRING & LINKING

IMPORTANT:

• These steps are for wireless audio streaming only.

• When pairing or linking, do only one process at a time. Starting one process before the other is finished

will cancel the first.

• The tone sequences for pairing and linking are different, so you can easily distinguish between the two.

ABOUT RANGE

Truesonic wireless loudspeakers use an advanced, extended-range Bluetooth antenna design, allowing for

ranges far greater than traditional Bluetooth devices. The typical range is 60-80 feet (18-24 meters) with a

clear line of sight. However, the range may vary depending on your source device and the environment.

To maximize the range:

• Set your source device on a flat surface and make sure there are no obstacles between the

loudspeaker and your device (e.g., walls, furniture, etc.).

• Turn off your source device’s Wi-Fi.

• Turn off any unneeded 2.4 GHz devices in the nearby vicinity (e.g., other Bluetooth devices, baby

monitors, Wi-Fi access points, microwave ovens, etc.).

• Try using a different Bluetooth source device. Bluetooth signal strength varies between different

devices.

PAIRING

To pair the speaker to your Bluetooth device:

1. Do this on one loudspeaker only: With the loudspeaker powered on, press and release its PAIR

BUTTON. Its LED will flash, and you will hear a tone sequence from the loudspeaker. (If you are using

two Truesonic wireless loudspeakers, this one will be the "master." Also see the LINKING section

below.)

2. From your Bluetooth device’s settings page, enable

Bluetooth and select ALTO PRO WIRELESS

TS115W as the device. When paired successfully,

you will hear a final "confirmation tone" from the

loudspeaker and the PAIR BUTTON LED will light

continuously. (This process may take up to 60

seconds.)

Note: If your device prompts you to select the con reo speakers,” “advanced nection type, select “ste

audio,” or a similar option.

3. Turn the loudspeaker's BLUETOOTH VOLUME knob to its lowest setting.

4. On your Bluetooth device, play music. We recommend setting the playback volume at its maximum

setting. Then, adjust the loudpeaker’s BLUETOOTH VOLUME knob to the desired level.

5. Once your device is paired to the speaker, the speaker will remember the device even after power-

cycling it. To reconnect it, go to your device’s Bluetooth settings page and select “Connect” to re-

establish the connection.

LINKING

If you are using two Truesonic wireless speakers:

1. Make sure no audio is playing from your Bluetooth

device. If it is, pause/stop playback and wait 5

seconds.

2. Press and release the STEREO LINK BUTTON on

each speaker.

3. Both loudspeakers’ LEDs will flash while

"searching" for each other, and you will hear a tone

sequence from both loudspeakers. (This process may take up to 60 seconds. However, the very first

time you link the loudspeakers, the process may take up to 3 minutes.)

4. When they are successfully linked, you will hear a final "confirmation tone" from both loudspeakers and

the STEREO LINK BUTTON LEDs on both loudspeakers will light continuously.

Note: The stereo signal will be split between the two loudspeakers: the master loudspeaker will play the left

channel; the slave loudspeaker will play the right channel.

Tip: When using two loudspeakers, we recommend labeling the master loudspeaker so you can distinguish

between the two in future setups.

Bluetooth is a registered trademark of Bluetooth SIG.

Note: If your device prompts you to enter

a PIN code to pair it to the speaker, enter

0000 (four zeros).

Note: The loudspeaker that is connected

to your source device is the “master”; the

linked loudspeaker is the “slave.” The

source device sends its signal to the

master, and the master relays the signal to

the slave.

Product specificaties

Merk:	Alto
Categorie:	Niet gecategoriseerd
Model:	TS115W
Kleur van het product:	Zwart
Gewicht:	17690 g
Breedte:	429.2 mm
Diepte:	363.2 mm
Hoogte:	679.4 mm
Materiaal behuizing:	Polypropylene (PP), Steel
LED-indicatoren:	Ja
Bluetooth:	Ja
Connectiviteitstechnologie:	Bedraad en draadloos
Type stroombron:	AC
Gemiddeld vermogen:	800 W
Equalizer-instellingen:	Ja
Aanbevolen gebruik:	Universeel
Impedantie:	- Ohm
Geschikt voor buitengebruik:	Ja
Audio-uitgangskanalen:	1.0 kanalen
Speaker plaatsing:	Floor, Tabletop/bookshelf
Woofer:	Ja
Frequentiebereik:	42 - 20000 Hz
Soort magneet:	Neodymium
Bereik van Bluetooth:	9.14 m
Luidspreker soort:	2-weg
Versterker:	Ingebouwd
Diameter woofer:	15 "
Aantal woofer drivers:	1
Diameter hogetonenluidspreker:	0.75 "
AC-ingangsfrequentie:	50 - 60 Hz
Crossover frequentie:	2500 Hz
Versterker klasse:	D