Allen & Heath GL3300 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Allen & Heath GL3300 (14 pagina's) in de categorie Mengpaneel. Deze handleiding was nuttig voor 19 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/14
Publication AP2564
&
FITTING INSTRUCTIONS
For information on using SYS-LINK please refer to APPLICATIONS NOTE AP2565
This option connects a GL3000 or GL3300 console as a channel expander to a
second console with just one or two interconnecting cables.
Interconnecting cables not supplied.
Issue 2 Dec 97
Kit Part No: GL3000-SL1
Single option to install SYS-LINK to one GL3000 console to allow
interconnection to a second console already fitted with SYS-LINK.
Kit Part No: GL3300-SL1
Single option to install SYS-LINK to one GL3300 console to allow
interconnection to a second console already fitted with SYS-LINK.
ALLEN & HEATH
GL3000 & GL3300 SYS-LINK OPTION2
FITTING THE SYS-LINK EXPANDER OPTION
D type connector
fixings already fitted.
8 x AB2189
Å’
SOLDER
1pt CROSS POINT
•TOOLS REQUIRED :
LONG NOSE
SOLDERING IRON
with small tip
Contents:
1x SYS-LINK circuit board assembly with interconnecting harness and mountings already fitted.
4x SYS-LINK ribbon harness with D type connector fixings already fitted.
1x SYS-LINK Fitting Instructions (AP2664)
1x SYS-LINK Application notes (AP2665)
fig. 1
CHECK THE CONTENTS :
Please check carefully the SYS-LINK circuit board assembly is the correct one for the console in which
it is to be installed.
ALLEN & HEATH GL3000 & GL3300 SYS-LINK OPTION 3
PRELIMINARY:
Ž
To fit the SYS-LINK option it is necessary to partially remove GROUP 1 circuit board assembly to enable
access to the SYS-LINK solder pads. It is not necessary to remove any other circuit board assemblies as
access to the SYS-LINK solder pads is easier and the solder connections can be made with the circuit
assemblies in place.
REMOVE THE KNOB CAPS:
•
Pull off the knob caps from Group 1 channel only. The switch caps can remain in place. Using a suitable
nut driver, remove the pot nuts.
Then invert the console and place it on its front.
D
A
B
Chan.1
Chan.24
CONSOLE FRONT
C
24 channel console inverted with the base cover removed.
fig. 2
’DISCONNECTING THE HARNESS ASSEMBLIES:
REMOVE THE BLANKING PLATE :
‘
The blanking plate is located below the input connectors on the rear panel of channels 9 to 16. Unscrew
the retaining screws and remove the blanking plate.
Disconnect the MAIN HARNESS (A) plugged into the connectors mounted along the edge of the circuit
boards. It is not necessary to disconnect channels 1 to 15.
Then disconnect the 16 way MASTER HARNESS (B) from the GROUP circuit board assemblies but not from
the MASTER CONNECTOR circuit board assembly (C). Drape the harness over the rear of the console.
Disconnect the flexible flat cables (D) plugged into the GROUP and LEFT circuit boards.
REMOVE THE CONSOLE BASE :
Refer to fig. 7.
•


Product specificaties

Merk: Allen & Heath
Categorie: Mengpaneel
Model: GL3300

Heb je hulp nodig?

Als je hulp nodig hebt met Allen & Heath GL3300 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Mengpaneel Allen & Heath

Handleiding Mengpaneel

Nieuwste handleidingen voor Mengpaneel