Akuvox E11R Handleiding

Akuvox Intercomsysteem E11R

Lees hieronder de 📖 handleiding in het Nederlandse voor Akuvox E11R (2 pagina's) in de categorie Intercomsysteem. Deze handleiding was nuttig voor 65 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Allen Wrench x 1

Rope x 1

E11X x 1

ST4x20 screw x 4 Screw fixing seat x 4

M2.5x6 screw x 2Back cover x 1

Installaon

With 86 embedded box in the wall

Fix the wall-mounting bracket on

embedded box with two M4x30

screws.

Mark the two holes of the

wall-mounting bracket on the

wall.

Take down two M4x30 screws

and remove the wall-mounting

bracket.

Fix the wall-mounting bracket with two

ST4x20 screws and two M4x30 screws.

Insert two screw fixing

seats into the holes.

Use a hand drill with 5mm diameter bit to

make two 25mm depth holes in the

marked positions.

Step 2: Back cover Installaon Applicaon Network Topology

Fasten the back cover with four

M3x6 screws, then fix four

wall-mounting screws on the

back of E11X.

Conﬁguraon

For convenient wiring, hang

E11X on the wall-mounting

bracket with rope.

Make cables go through the back

cover, connecting to the corresponding

interfaces of the main board.

Without 86 embedded box in the wall

Universal Accessories:

Wall-mounting screw x 4

Step 1: Bracket/Box Installaon

Wall Mounng

23 4

1. Access the Web UI: Input the IP address into web browser to configure the phone.

2. Account Registration: On web UI, go to the path: page Account -> Basic

more information)

3. Configure the Push Button: On web UI, go to the path: Intercom -> Basic -> Push Button

to configure the call number.

4. Configure the code to open the relay: On web UI, go to the path: Intercom -> Relay

-> Relay ID/DTMF and choose the DTMF code number in corresponding area.

Rubber Plug x 3 S,M,L（）

Camera

RF card reader

Call buon&Status LED

Mic

E11X

Infrared sensor

Infrared LED

Photosensive sensor

Mark the four holes of the

wall-mounting bracket on

the wall for the screws.

Use a hand drill with 5mm diameter

bit to make four 25mm depth holes

in the marked positions.

Fix the wall-mounting bracket

with four ST4x20 screws.

Insert four screw fixing seats into

the holes.

Cable locking plate x 1

Note: For more LED settings, please refer to E11X webUI: Intercom -> LED Setting.

Network Video Recorder

(third party)

SIP Video Phone

LAN

PoE PoE

E11X E11X

PoE PoE

E11X E11X

PC(third party)

PoE PoE

Indoor Monitor

Speaker

Select a suitable size rubber plug

to push all the cables into the back

cover. Fix cable locking plate to

the back cover with two M2.5x6

screws.

After successful installation,

check the stability of device.

Insert the four wall-mounting screws on

the device into the corresponding holes

on the wall-mounting bracket, and then

press down to slide the wall-mounting

screws into the groove. Then use the

Allen Wrench to tighten the device with

two M3x6 screws.

TZ-SM-002038

陈凌谨

余芳

赵欣

2019.11.12

Operaon

Indicators

IP Announcement

Make a call:

1. Press the call button to call indoor SIP Phone.

2. During the talk, called party can press pre-configured code number to unlock the door.

Receive a call:

E11X supports Auto Answer by default. Incoming call will be answered automatically.

1. While E11X starts up normally, hold the call button for several seconds after the Status

LED turns blue, voice system will enter IP announcement mode.

2. In announcement mode, the IP address will be announced periodically.

3. Press Call Button again to quit the announcement mode.

4. In announcement mode, phone announces "IP 0.0.0.0" if no IP address is gained.

M3x6 screw x 6

M4x30 screw x 2 Wall-mounting bracket x 1

E11XE11X

E11X

E11X E11X E11X

E11 AK版挂墙快速安装指南

AKUVOX (XIAMEN) NETWORKS CO., LTD.

ADD: 10/F, NO.56 GUANRI ROAD, SOFTWARE PARK II, XIAMEN 361009, CHINA

www.akuvox.com

Notice Information

Akuvox E11X firmware contains third-party open source software under the terms of the GNU General Public

License(GPL). Akuvox is committed to meeting the requirements of the GNU General Public License (GPL) and will

make all required source code available.

The source code of software under the terms of GNU GPL can be downloaded online: http://www.akuvox.com/gpl.

Information contained in this document is believed to be accurate and reliable at the time of printing. This document is

subject to change without notice, any update to this document can be viewed on Akuvox’ s website:

Product specificaties

Merk:	Akuvox
Categorie:	Intercomsysteem
Model:	E11R
Soort bediening:	Knoppen
Kleur van het product:	Zwart
Breedte:	85 mm
Diepte:	27.5 mm
Hoogte:	145 mm
Materiaal behuizing:	Kunststof
Kleur:	Ja
AC-adapter ingangsspanning:	12 V
Beeldschermdiagonaal:	- "
Stemcodecs:	G.711a, G.729
Connectiviteitstechnologie:	Bedraad
Ondersteunde video-modi:	720p
Minimale belichting:	0.1 Lux
Kijkhoek, horizontaal:	116 °
Kijkhoek, verticaal:	60 °
Nachtvisie:	Ja
Maximale beeldsnelheid:	30 fps
Luidspreker:	Ja
Aantal Ethernet LAN (RJ-45)-poorten:	1
Ingebouwde luidsprekers:	Ja
Aantal luidsprekers:	1
Omvang optische sensor:	1/2.7 "
Megapixels:	2 MP
Type beeldsensor:	CMOS
Maximale videoresolutie:	1280 x 720 Pixels
Ingebouwde microfoon:	Ja
Ethernet LAN, data-overdrachtsnelheden:	10, 100 Mbit/s
Bekabelingstechnologie:	10/100Base-T(X)
Netwerkstandaard:	IEEE 802.3af
Temperatuur bij opslag:	-40 - 70 °C
Aantal knoppen:	1 knoppen
Backlight toetsen:	Ja
Ondersteunde netwerkprotocollen:	802.3af
Ophangsysteem voor aan de muur:	Ja
Power over Ethernet (PoE):	Ja
Binnenunit inbegrepen:	Nee
Buitenunit inbegrepen:	Ja
Vermogen luidsprekers:	3 W
Beheerprotocollen:	IPv4, HTTP, HTTPS, FTP, SNMP, DNS, NTP, RTSP, RTP, TCP, UDP, ICMP, DHCP, ARP
Wifi:	Nee
Bedrijfstemperatuur (T-T):	-20 - 65 °C
Relatieve vochtigheid in bedrijf (V-V):	10 - 90 procent
Stroomtype van binnenunit:	DC
Video-codecs:	H.264