AJH Synth MiniMod VCF Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor AJH Synth MiniMod VCF (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 148 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
VCF User Guide
Thank you for purchasing the AJH Synth MiniMod VCF module, which like all AJH Synth Modules,
has been designed and handbuilt in the UK from the very highest quality components. We hope
that it will help and inspire you towards creating some great music and soundscapes!
The MiniMod VCF is a very faithful replica of the four pole 24db/octave low pass lter used in the
early Model D synthesiser. By using fully matched discrete ladder transistors along with audio-
phile grade capacitors and operational ampliers in the audio signal path, it captures the vintage
sound and vibe of this epic lter and combines it with the versatility of the Eurorack modular
format.
The front panel provides a three channel input mixer and a large lter cuto control, along with
1/3 and 2/3 CV inputs to emulate the action of the original VCF keyboard switches. There is also a
variable Exponential CV input which is about 30% more sensitive than the 1v/oct input, which
allows some nice over modulation eects.
Added features include Voltage Controlled Emphasis (Resonance) which uses a Vactrol as the
control element. This approach was chosen because it is a purely resistive element and impor-
tantly has no impact on the vintage sound of the lter. The fast acting Vactrol chosen allows
modulation speeds up into the audio range. The lter will of course self-resonate and act as a sine
wave oscillator too.
An overdrive facility can be selected using the onboard jumper which allows the input to the lter
core to be substantially overdriven - great for adding a bit of extra dirt to the sound!
Module width is 14 HP of Eurorack space and it is compatible with standard Eurorack cases. The
height of the panel is 128.5mm, and depth is 26mm . There are four mounting holes at the
corners of the module and we provide 4 of M3 rack xing screws, along with a Eurorack compat-
ible power cable. Current consumption is 45mA from the +12V supply rail and 30mA from the
-12V supply rail.
All AJHSynth modules are covered by a one year guarantee against manufacturing defects.
Note:
It is very important that the power supply ribbon cable is connected correctly, see theadjustment and
calibration” section for an illustration of the correct orientation.
Discrete Transistor Ladder Filter
mod
www.ajhsynth.com
IN 2
2/3 CV1V/Oct
IN 3IN 1
INPUT 1
FREQ CV EMP CV
INPUT 2 INPUT 3
EMPHASIS
FREQ-CV OUT
EMP-CV1/3 CV
-2
-4 4
2
TRANSISTOR LADDER FILTER
mod
2 8
4 6
010
2 8
4 6
010
2 8
4 6
010
28
46
0 10
28
46
0 10
28
46
0 10
FREQ
7 Cuto Freq.
9 Freq. CV Level
4 Input 1 Level
11 1/3 CV Input
10 1V/Oct Input
8 Freq. CV Input
1 Audio Input 1
Emph. CV Level 15
2 Audio Input 2
Input 2 Level 5
Input 3 Level 6
2/3 CV Input 12
Emp. CV Input 14
Audio Output 16
Audio Input 3 3
Emphasis Level 13
1 Audio Input 1 : Audio Input 1 forms part of a 3 input audio mixer which is attached to the front end of the
lter. This Input is mixed with Input 2 and Input 3 at a level set by Audio 1 Level control
(4). Typically the output from a VCO would be connected to this Input, but any AC signal
with a level of up to +/- 5 Volts is acceptable. .
All three Audio Inputs are for audio signals only, the lter signal path is AC coupled so DC
control voltages are not useful here but will not cause any problem if accidentally
connected.
2 Audio Input 2 : Audio Input 2 forms part of a 3 input audio mixer which is attached to the front end of the
lter. This input is mixed with Input 1 and Input 3 at a level set by Audio 2 Level control
(5). Signal levels of up to +/- 5 Volts are acceptable.
3 Audio Input 3 : Audio Input 3 forms part of a 3 input audio mixer which is attached to the front end of the
lter. This input is mixed with Input 1 and Input 2 at a level set by Audio 3 Level control
(6). Signal levels of up to +/- 5 Volts are acceptable.
4 Input 1 Level : Sets the amount of signal from Audio Input 1 (between 0% and 100%) that is mixed with
Audio Inputs 2 & 3 and sent to the lter core.
5 Input 2 Level : Sets the amount of signal from Audio Input 2 (between 0% and 100%) that is mixed with
Audio Inputs 1 & 3 and sent to the lter core.
6 Input 3 Level : Sets the amount of signal from Audio Input 3 (between 0% and 100%) that is mixed with
Audio Inputs 1 & 2 and sent to the lter core.
Controls, Inputs and Outputs
7 Cuto Freq. : The Cuto Frequency control manually varies the cut o frequency of the low pass
lter. At the minimum setting (fully counter clockwise) the lter will cut o all frequencies
with no audio output and at the maximum setting the lter will pass all frequencies. It is
still active when using CV control, in which case it acts as an oset control.
(Audio)
(Audio)
(Audio)
8 Freq CV Input : Connect an external control voltage to this Input for voltage control of the lter cuto
frequency. The amount of signal passed to the lter core control circuitry can be adjusted
with the Freq. CV Level control (9)
9 Freq. CV Level : Sets the amount of control voltage (between 0% and 130%) which is sent from the Freq.
CV Input (8) to the lter cuto circuitry. It has a greater range than the 1 V/Oct Input so
that overmodulation eects are possible. 1V / Octave from the Freq. CV Input occurs
with this control knob pointing to position 7 ( 2 oclock).
10 1 V/Oct Input : A voltage applied to this Input changes the lter cuto at the rate of 1 volt per octave, or
if the lter is in full self oscillation (Emphasis Control fully clockwise) it will control the
pitch of the resulting sine wave at the rate of 1 V/Oct. When compared to the Model D this
emulates having “Keyboard Control” switches 1 and 2 “On.
11 1/3 CV Input : A voltage applied to this input changes the lter cuto at the rate of 333 mV per octave.
When compared to the vintage Model D this is the equivalent of having “Keyboard
Control” switch 1 “On and switch 2 “O.
12 2/3 CV Input : A voltage applied to this input changes the lter cuto at the rate of 666 mV per octave.
When compared to the vintage Model D this is the equivalent of having “Keyboard
Control” switch 2 “On and switch 1 “O.
13 Emphasis Level : This control manually regulates the amount of internal feedback applied to the lter core.
“Emphasis” is now more commonly known as resonance in the modular synth world, they
are just dierent words for the same eect.
At high levels of feedback (between positions 8 and 10) the lter will self-oscillate, so that
even without any audio input to the lter a sine wave output is generated and the
frequency can be controlled by applying control voltages to the 1V/Oct, Exp. CV, 1/3 or
2/3 inputs.
Like the Model D, when using the 1 V/Oct the sinewave can be played in the same
manner as a VCO with a tracking range of 3 - 4 octaves.
The CV scaling is not temperature corrected so it may drift with changes in ambient
temperature. Under normal circumstances it should track reasonably accurately over a
four octave range. Again, this correctly emulates the behaviour of the vintage Model D
lter.
14 Emp CV Input : Applying a control voltage to this Input will vary the Emphasis at the level set by the
Emp. CV Level control (15). Acceptable input voltage range is +/- 5V
15 Emp. CV Level : This varies the amount of control voltage passed from the Emp. CV Input (14) to the lter
core and it’s range is 0% to 100%. The manual Emphasis Level control (13) is still active
when using external CV control of Emphasis and acts as an oset control.
16 Audio Output : This is the audio output for the signal after passing through the lter core and would
typically be connected to the Audio Input of a VCA. The output level is dependent upon
the input level, with a single input of +/- 5V to (for example) Audio Input 1 and Audio 2
Level at 100% the gain would be unity, i.e. output would also be +/- 5V.
Removing this jumper increases the gain of the signal by around 70% BEFORE it is fed to
the lter core, which can give a nice overdrive eect. This can be used to emulate the
vintage Model D “trick” of plugging the headphone output back into the VCF External
Input.
With this jumper removed there is a proportionate (70%) increase in VCF output level and
this should be compensated further down the signal chain. So, if being fed into a VCA the
VCA Input Level control will need to be turned down to compensate for this higher signal
level.
E Gain Jumper :
(J1 on PCB)


Product specificaties

Merk: AJH Synth
Categorie: Niet gecategoriseerd
Model: MiniMod VCF

Heb je hulp nodig?

Als je hulp nodig hebt met AJH Synth MiniMod VCF stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd AJH Synth

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd