ACE 3014727 Handleiding

ACE Deurbel 3014727

Lees hieronder de 📖 handleiding in het Nederlandse voor ACE 3014727 (4 pagina's) in de categorie Deurbel. Deze handleiding was nuttig voor 57 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
-1-
© 2000 598-1066-00
Your doorbell includes:
• Doorbell chime
• Doorbell button/transmitter w/battery
• Hardware pack
You'll need to buy 2 "C" alkaline batteries for the chime. In typical use,
alkaline batteries will last up to one year.
Model 3014727
Wireless Doorbell
Press the doorbell button to verify that the
doorbell and chime work properly. If the
chime does not sound see the troubleshooting
guide on page 3.
Doorbell button
Operation
Push
Button
3. Before mounting, test the doorbell range.
Put the chime where you want to mount it
and temporarily place the doorbell button on
the doorjamb. Press the doorbell button.
Battery
Battery
Battery
BatteryBattery
Battery
Battery
Battery
BatteryBattery
2. Install the 2 alkaline
"C" batteries. Make
sure the batteries are
oriented properly.
1. Open the chime
case. Press in catch
on the bottom of the
chime and lift the
case open.
®
-2-
4. Mount the doorbell button and chime.
Use either screws or double sided tape to mount the doorbell button.
To mount with screws, remove the back of the case by pushing in the tab on
the bottom with a small screwdriver and rotating the blade.
Attach the back of the case to the door jamb or wall. Snap the front of the
button back on.
When attaching the doorbell button using the double sided tape, make sure
the surface of the door jamb or wall is clean.
The chime can be mounted by using the 2 holes in the back of the case, or
by using 1 screw with the keyhole.
Holes for Wall
Mounting
Chime Back Case
Keyhole
Close Chime Case
From Top
1 "∑
Snap the front of the chime case back on. Start with the top edge of the case
aligned with the top of the back plate.
-3-
Inside
Doorbell
Button
NOTE: Most installations will not require you to change any of the jump-
ers on your doorbell. However, if you need to make changes to the
factory settings follow the instructions below.
SAME
For a backdoor chime sound,
add a jumper on the far right ter-
minal of doorbell button.
Trouble shooting
Chime doesn't sound:
• Make sure the doorbell button and the chime channels are the same (See
above).
• Check orientation of doorbell button battery (See page 4).
• Check the doorbell button and chime batteries, replace if necessary.
Batteries seem OK, but the chime doesn't work when installed:
• Don't mount the chime or doorbell button on metal or near metal studs.
This reduces the transmitter range. Use " to " wood shims to move the4 2
chime or doorbell button off the metal surface.
• Don't mount the chime too close to ground level concrete slabs. This may
also reduce the range. Mount the chime away from the floor.
• Try different locations for the chime closer to the doorbell button. Also try
to orient the chime at a different angle to increase the range.
The range of the doorbell depends on location, temperature and battery condition.
} {
Only if another doorbell
system is on the same
c hannel and interferes, set
the doorbell button and
chime to a new channel by
removing or adding the
same seven left jumpers on
both the button and chime.
Inside
Chime
Jumper
not used


Product specificaties

Merk: ACE
Categorie: Deurbel
Model: 3014727

Heb je hulp nodig?

Als je hulp nodig hebt met ACE 3014727 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Deurbel ACE

ACE

ACE 3014727 Handleiding

11 November 2022

Handleiding Deurbel

Nieuwste handleidingen voor Deurbel