2hp Lo-Fi Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor 2hp Lo-Fi (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 5 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
2hp Lo-Fi
2hp
OUT
IN
Lo-Fi
A
WOW
HISS
POP
Analog/Digital Degradation Emulator
Audio Input
Range: 10Vpp
Wow & Flutter
CV Input
Range: -5V to +5V
Wow & Flutter
Controls the variation and
amount of tape speed modu-
lation, resulting in undulating
pitch uctuations and dips.
The eect is o when the knob
is fully counter clockwise. Hiss
Controls the amount of tape
noise emulation. This eect
is a combination of noise,
amplitude modulation, and
dynamic ltering.
The eect is o when the
knob is fully counter clock-
wise.
Hiss CV Input
Range: -5V to +5V
Pops & Crackles
CV Input
Range: -5V to +5V
Pops & Crackles
Controls the amount of pops,
crackles, and dropouts on the
audio signal. The last 1/3 of
the knob introduces soft tape
saturation to the signal.
The eect is o when the knob
is fully counter clockwise.
Audio Output
Range: 10Vpp
Tech Specs
Width: 2HP
Depth: 45mm
Power Consumption:
+12V=85mA, -12V=7mA,
+5V=0mA
Watch The Demo
ANALOG MODE
Toggle to LEFT
*Digital Mode on page 2
Mode Toggle
Toggles between Analog and
Digital modes.
2hp
OUT
IN
Lo-Fi
Discover more at https://www.twohp.com/modules/lo-
Audio Input
Range: 10Vpp
Bitcrusher
CV Input
Range: -5V to +5V
Bitcrusher
Controls the amount of bit-
depth reduction on the audio
signal, from 32-bit to 1-bit.
The eect is o when the knob
is fully counter clockwise. Reduction
Controls the amount of
sample-rate reduction on
the audio signal. Maximum
reduction is fully clockwise.
The eect is at 48kHz when
the knob is fully counter
clockwise.
Reduction
CV Input
Range: -5V to +5V
Distortion
CV Input
Range: -5V to +5V
Distortion
Controls the amount of dis-
tortion on the audio signal.
Maximum distortion is fully
clockwise.
The eect is o when the knob
is fully counter clockwise.
Audio Output
Range: 10Vpp
DIGITAL MODE
Toggle to RIGHT
Mode Toggle
Toggles between Analog and
Digital modes.
Module Installation
• To install your 2hp module, locate a space with the appropriate HP in your rack for instal-
lation.
• Next, connect the module’s power cable to your power supply. The cables on this end are
keyed, though you should make sure to align the red stripes on both connectors to en-
sure safe and proper connection. Our illustration uses a ying bus cable, though the same
action applies for busboards/alternate power solutions. See the gure below for refer-
ence:
• Next, make sure your module’s power cable is properly connected to your module. For
2hp modules, conrm that your cable’s red stripe aligns with the white marker line on
the module’s PCB, just above the power header. You may notice that even though there
is only 1 row of 5 pins on your 2hp module, but 2 rows on the power cable. You can use
either row of 5 pin connectors on the cable with your module, so long as the red stripe is
properly aligned. See gure below for reference:
• Finally, mount your module to the rails
using 2.5mm mounting screws and the
included sliding mounting nuts. Your
module is now ready to be powered on and
patched!


Product specificaties

Merk: 2hp
Categorie: Niet gecategoriseerd
Model: Lo-Fi

Heb je hulp nodig?

Als je hulp nodig hebt met 2hp Lo-Fi stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd 2hp

2hp

2hp Swarm Handleiding

30 Januari 2025
2hp

2hp Lo-Fi Handleiding

30 Januari 2025
2hp

2hp Bell Handleiding

30 Januari 2025
2hp

2hp Trim Handleiding

30 Januari 2025
2hp

2hp Comb Handleiding

30 Januari 2025
2hp

2hp Rout Handleiding

30 Januari 2025
2hp

2hp S+H Handleiding

30 Januari 2025
2hp

2hp AVert Handleiding

30 Januari 2025
2hp

2hp Delay Handleiding

30 Januari 2025
2hp

2hp Verb Handleiding

30 Januari 2025

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd