Zortrax Inventure Handleiding

Zortrax 3D Printer Inventure

Lees hieronder de 📖 handleiding in het Nederlandse voor Zortrax Inventure (55 pagina's) in de categorie 3D Printer. Deze handleiding was nuttig voor 53 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/55
3D Printer User Guide
Inventure
Table of contents
Introduction 3
Intended Use of the Zortrax Inventure
3
General Safety Information 4
Warning and Safety Labels on Zortrax Devices
6
Learn More About the Zortrax Inventure 7
How does the Zortrax Inventure Work?
8
What’s in the Box
9
Main Components 10
Zortrax 3D Printing Technology Glossary
13
First Use Preparation 16
Firmware Installation 23
Navigating through the Zortrax Printer Menu
24
Operational Modes of Zortrax Inventure 26
Material Loading 27
Platform Leveling
29
Nozzle Alignment Calibration 31
Z-SUITE Installation 35
Starting and Removing a Print 35
Available Materials
40
Basic Maintenance and Service Work
40
Support and Troubleshooting 44
Specification 52
Recycling 54
©2020, Zortrax S.A. All rights reserved. All trade names, logos and trademarks mentioned in the following
document are registered trademarks of Zortrax and are subject to legal protection.
3
Introduction
Read this User Guide carefully and thoroughly before operating Zortrax products for the first
time. The User Guide includes basic information about the 3D printer, safety and protection
guidelines as well as advice on preparing the machine for the first printing and basic main-
tenance work. Ignorance and non-compliance with these instructions may result in property
damage, injuries, device failures or lower quality of 3D prints. It is also necessary to ensure
that every 3D printer user knows, fully understands and follows the instructions provided in
this User Guide.
The Manufacturer makes every effort to ensure that Zortrax products are safe in transporta-
tion, installation, usage, storage and disposal.
However, the Manufacturer is not responsible for damage, injuries, failures, and costs resulting
from improper transportation, installation, usage, storage, and disposal given the lack of direct
and indirect control over the device, and a number of other factors influencing the device and
those which are beyond the Manufacturer’s knowledge.
Furthermore, the users should take into consideration the risk of possible faults of the device
resulting from material and production defects.
Intended Use of the Zortrax Printers
The Zortrax Inventure works in the Layer Plastic Deposition (LPD Plus) technology, in which pre-
viously melted materials are deposited on a surface layer after layer in order to form a predesi-
gned shape. The extruder is equipped with several heating points which allow the materials to
exit the nozzles and be deposited onto the platform without causing blockages.
The users are responsible for qualifying and determining the intended use of the 3D printed
models. The Manufacturer takes no responsibility for any use of the printed objects, especially
when these objects constitute a part of safety equipment or strictly regulated medical, military
or space science equipment.
Due to the size and specificity, Zortrax devices are not intended for use by children under the
age of 14 and by people with reduced manual, motor and psychomotor skills. The Manufactu-
rer recommends providing assistance and guidance to people with disabilities and older adults
who wish to operate Zortrax printers.


Product specificaties

Merk: Zortrax
Categorie: 3D Printer
Model: Inventure
Kleur van het product: Zwart
Ingebouwd display: Ja
USB-poort: Nee
Ethernet LAN: Nee
Geïntegreerde geheugenkaartlezer: Ja
Compatibele geheugenkaarten: SD
Kijkglas: Nee
Vermogensverbruik (max): 300 W
Temperatuur bij opslag: 0 - 35 °C
Wifi: Nee
AC-ingangsspanning: 110 / 240 V
AC-ingangsfrequentie: 50 / 60 Hz
Bedrijfstemperatuur (T-T): 15 - 30 °C
Breedte mondstuk: 0.4 mm
Printmateriaal: ABS, Acrylonitrile Styrene Acrylate (ASA), Nylon, Polyethylene Terephthalate Glycol (PETG), Polylactic acid (PLA)
Ondersteunde filamentdikte: 1.75 mm
Maximaal afdrukformaat: 135 x 135 x 130 mm
Laagdikte (min): 0.15 mm
Laagdikte (max): 0.3 mm
Aantal printkoppen: 2
3D-scanner: Nee
Graveermodule: Nee

Heb je hulp nodig?

Als je hulp nodig hebt met Zortrax Inventure stel dan hieronder een vraag en andere gebruikers zullen je antwoorden