Yamaha SPS-80 Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Yamaha SPS-80 (4 pagina's) in de categorie Geluid. Deze handleiding was nuttig voor 66 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/4
English
E-1
Français
Deutsch
595 (23-7/16”)
297 (11-11/16”)
900 (35-7/16”)
650 (25-9/16”)
153 (6”)
47(1-7/8”) 6 (1/4”)
M4 (3/16”)
300 (11-13/16”)
●This speaker stand is only for the speaker systems listed
in “USABLE SPEAKERS” below. Do not use the
speakers other than these listed.
●To prevent the speaker from falling, use the screws and
parts provided with the stand.
●To prevent the speaker stand from falling over, select a
location which is flat and stable.
●To avoid accidents resulting from tripping over loose
speaker cables and to prevent the speaker stand from
falling over, fix the speaker cables to the wall, etc.
●Do not let the children lean on the stand as this might
cause the serious accidents resulting from the falling
over of the speaker stand.
PRECAUTIONS
Dimensions (W x H x D): 300 x 650 – 900 x 300mm
(11-13/16” x 25-9/16”
– 35-7/16” x 11-13/16”)
Weight: 2.1 kg (4 lbs. 10 oz.)
YAMAHA
●NX-230P
(the main and rear speakers included in the NS-P230/
NS-P236 speaker package)
●NX-220P
(the main and rear speakers included in the NS-P220
speaker package)
●NX-S80S
(the front and rear speakers included in the AVX-S80
sound system)
●NX-S60S
(the front and rear speakers included in the DVX-S60
sound system)
●NX-S77E
(the rear speakers included in the AV-S77 sound
system)
●NX-VS10E
(the rear speakers included in the VS-10 sound system)
* Use a speaker of 1 kg or less.
* Use a speaker with a screw hole of 4 mm in diameter
for attaching the speaker mounting bracket.
DIMENSIONS
SPS-80
SPEAKER STAND
Read this before setup
Thank you for selecting this YAMAHA SPS-80 speaker stand.
●To prevent the speaker stand from discoloring and
warping, keep the speaker stand away from the stoves
and places where it will be exposed to direct sunlight,
etc.
●Do not attempt to clean the speaker stand with chemical
solvents as this might damage the finish. Use a clean,
dry cloth.
●Secure placement or installation is the owner’s
responsibility.
YAMAHA shall not be liable for any accident caused
by improper placement or installation of speakers.
SETUP
INSTRUCTIONS
SPECIFICATIONS
USABLE SPEAKERS
Top view
Side view
(When shortened to minimum) (When extended to maximum)
(mm/inch)
SPS-80 ENG(02.6.17)b 02.6.19, 11:57 AM1
E-2
䡵SETUP PROCEDURES
(You will need a screwdriver for the setup.)
1
Attach the support to the base by fastening the
three + face screws from the holes on the bottom
of the base.
* Do not overtighten the + self-machine screws. Doing
so may damage the screws or assembly.
2
Pass the speaker cable through the support from
the bottom.
* A speaker cable more than 4 mm x 2 mm in diameter
cannot be used. If you use such a cable, connect it to
the speaker’s terminals without passing it through the
pole.
NAME QUANTITY
1Pole 2
2Support 2
3Base 2
4+ face screws 6
(Diam. x Length: 4 x 8 mm)
5Hexagon socket set screws 5
(Diam. x Length: 4 x 6 mm)
6Wrench (hexagonal) 1
7Cable protection seal 2
8Rubber cap 2
SETUP PROCEDURES
Before beginning the setup, check the parts list
and make sure all the parts are included.
3
Remove the speaker mounting bracket from the
pole by removing the screw using the screwdriver.
4
Attach the speaker mounting bracket to the
speaker by screwing it into the screw hole on the
bottom of the speaker.
5
Pass the speaker cable through the pole from the
end without the cut.
Then pass the cable through the hole on the
speaker mounting bracket from the side with the
groove as shown in the figure.
Base
Support
Speaker cable
(not included)
Speaker
(not included)
Support
Speaker
mounting
bracket
Pole
Speaker
mounting
bracket
Pole
Speaker cable
Cut
Groove
Name plate
Front
Back
SPS-80 ENG(02.6.17)b 02.6.19, 11:57 AM2
English
E-3
6
Pull out the speaker cable in the length of 15 to 16
cm from the speaker mounting bracket. Then attach
the speaker mounting bracket to the pole so that
the speaker cable fits to the cut in the pole. This
will lock the speaker cable. After that, fasten the
screw.
7
Insert the pole to the support, and adjust the height
of the stand. After adjusting the height, fasten the
hexagon socket set screws into the two holes on
the support using the longer handle of the included
wrench, and attach the rubber cap to the support.
* The line on the pole shows the limit of the stand
height. Do not let the line of the stand height limit go
beyond the upper end of the support. Otherwise, the
hexagon socket set screw of the lower side becomes
ineffective and the fixation becomes unstable.
8
Adjust the speaker direction. Then put the wrench
into the hole of the speaker monting braket, and
tighten the bracket to the speaker by moving the
wrench counterclockwise.
9
Connect the speaker cable to the speaker’s
terminals correctly.
* Refer to the instruction manual of the speakers for
connecting the speaker cables.
10
Align the speaker cable to the grooved part of
the bottom of the base, and fix the cable on the
base by putting the protection seal on it.
The setup has completed.
In the same way, set up the other stand.
Make sure to note the following when stretching or
shortening the pole after the setup.
●Make sure to remove the cable protection seal before
stretching or shortening the pole.
●When stretching the pole, pull out the pole carefully with
the speaker stand laying along.
●When shortening the pole, retract the pole carefully
while pulling out the speaker cable slowly by hand from
the base side with the speaker stand laying along.
Wrench
(hexagonal)
15–16 cm
* Rubber cap
Hexagon
socket set
screw
Stand height
limit
Support
Cable
protection
seal
Cut
* The inside of the rubber cap has a space for
storing the wrench after the setup.
Screw
SPS-80 ENG(02.6.17)b 02.6.19, 11:57 AM3
Product specificaties
| Merk: | Yamaha |
| Categorie: | Geluid |
| Model: | SPS-80 |
Heb je hulp nodig?
Als je hulp nodig hebt met Yamaha SPS-80 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Geluid Yamaha
16 Augustus 2022
16 Augustus 2022
22 November 2021
15 Augustus 2022
2 Mei 2022
16 Augustus 2022
17 Augustus 2022
16 Augustus 2022
17 Augustus 2022
3 April 2022
Handleiding Geluid
- Geluid Philips
- Geluid Sony
- Geluid JBL
- Geluid Kenwood
- Geluid Motorola
- Geluid Nokia
- Geluid Olympus
- Geluid Onkyo
- Geluid Siemens
- Geluid Topcom
- Geluid Advance Acoustic
- Geluid Advanced Bionics
- Geluid Akg
- Geluid Aliph
- Geluid Alto Professional
- Geluid Amplicom
- Geluid Bang Olufsen
- Geluid Behringer
- Geluid Bellman
- Geluid Bellman Symfon
- Geluid Bluetrek
- Geluid Bose
- Geluid DAP Audio
- Geluid Datel
- Geluid Envivo
- Geluid Fender
- Geluid Fiio
- Geluid Focusrite
- Geluid Gear4
- Geluid Geemarc
- Geluid Gigabyte
- Geluid Gioteck
- Geluid Griffin
- Geluid HUMANTECHNIK
- Geluid Inakustik
- Geluid Ion
- Geluid Iqua
- Geluid Konig Electronic
- Geluid Korg
- Geluid Logitech
- Geluid MCS
- Geluid Mr Handsfree
- Geluid Native
- Geluid Nec
- Geluid Nxzen
- Geluid Phonak
- Geluid Plawa
- Geluid Plextor
- Geluid Power Dynamics
- Geluid Profoon
- Geluid Reflecta
- Geluid Roland
- Geluid Samson
- Geluid Sennheiser
- Geluid Sony Ericsson
- Geluid Speedlink
- Geluid Starkey
- Geluid Sweex
- Geluid T-Mobile
- Geluid TC Helicon
- Geluid Timewave
- Geluid Trust
- Geluid Velleman
- Geluid Velodyne
- Geluid Xqisit
- Geluid Zoom
- Geluid Jabra
- Geluid Cardo
Nieuwste handleidingen voor Geluid
2 Oktober 2023
2 Oktober 2023
2 Oktober 2023
2 Oktober 2023
2 Oktober 2023
2 Oktober 2023
2 Oktober 2023
2 Oktober 2023
2 Oktober 2023
2 Oktober 2023